User Manual

Operating Instructions - See Fig. 2&3
Icon Display Funtion Description
A -
Power /
Standby
Press Once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
B
‘FLAME EFFECT’ button this turns the ame effect ON or OFF independently of the
products other features.
+
Flame
Up
This Button will increase the brightness of the ame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
-
Flame
Down
This Button will decrease the brightness of the ame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
-
Flame
Cycling
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the ame effect to cycle from F2 to F5 in a continuous Loop.
-
Off
This will turn the ame effect off. If the heater is ON, the display will activate and remain
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
C
Sleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the ‘SLEEP TIMER’ displa
ys. (This icon is Green in Colour)
D
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the ame effect is ‘ON’ the display will turn off after 5 seconds, however if the
heater is being used independently of the ame effect. The low heat or high heat icon
will appear continuously in the display.
Low
Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW
HEAT’ icon. To Adjust the temperature setting the Temp Down or Temp Up buttons de-
scribed below must be used.
(This icon is Orange in Colour)
High
Heat
This icon in the display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH
HEAT’ icon. To Adjust the temperature setting the Temp Down or Temp Up buttons de-
scribed below must be used.
(This icon is Red in Colour)
Cool
Blow
This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by
the ‘COOL BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
- Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
E -
Temp
Up
Press multiple times to increase the heater temperature in 1
0
C in-
crements. The highest temperature that can be set 30
0
C .
When High Heat is selected, the letters ‘HH’ appear in the display, this means
the heat will remain ON continusously and is not controlled by the thermostat.
F -
Temp
Down
Press multiple times to lower the heater temperature in 1
0
C in-
crements. The lowest temperature that can be set is18
0
C .
-
‘Top light’ button this turns the top light ON or OFF independently of the products other
features.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (
0
C) to Fahrenheit (
0
F)
Press both Temp down ( ) and Temp up ( ) on the unit and hold until
beep is heard and display flashes. (To revert back to Celsius repeat this action)
Disable/Enable Heat Options
on product and remote control
Hold both Heat Cycle ( ) and Temp Up ( ), on the prod-
uct, for 5 seconds, when the heater has been disabled the display
will read “--” and beep 1 time. To enble heat repeat this action.
Disable/Enable Heat Options
on product only
Hold both Flame Cycle ( ) and Heat Cycle ( ), on the product, for 5 sec-
onds, when the heater has been disabled the product will beep. This will
disable heat control functions on the product only. To enble heat repeat this
action.Note: the remote control will still be able to operate heat functions.
G