Technical data

www.dimplex.de/en
30
2010
Brine-to-water heat pump in a compact design
Max. flow temperature for heating 58 °C
Casing colour white
Low-temperature brine-to-water heat pump
Compact design
SIK 7TE
Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design
screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD). Integrated brine compo-
nents enable direct connection of the heat source:
• Brine circulating pump (note the free compression)
• Expansion vessel (8 l)
• Safety valve and pressure manometer
Sound-optimised through insulated metal casing and double vibration-isolated compressor. Integrated solid-borne sound insulation
for direct connection to the heating system. Economiser for high coefficients of performance. Compact design with optional domestic
hot water preparation and integrated components for direct connection of an unmixed heating circuit (must not be used for bivalent
systems):
• Heat circulating pump (note the free compression)
• Overflow valve and safety module
• Expansion vessel (24 l)
Soft starter (from SI(K) 9 upwards), integrated flow and return sensors; external sensor (standard NTC-2), dirt filter and large-capacity
breather (1½“) with micro air bubble deposition for brine circuit included in the scope of supply.
Lower operating limit heat source (heating operation) -5 °C ; Upper operating limit heat source (heating operation) 25 ° C ;
Refrigerant R407C ; Connection heating 1¼ ⬙ ; Heat source connection 1¼ ⬙.
Order reference Art.-Nr. Heat output with 1 compressor /
COP B0/W35
Connection voltage Width x Height x
Depth
mm
Weight
kg
SIK 11ME 352990
11.8 / 4.4 (4.2)
1/N/PE ~230 V, 50 Hz
650 x 1115 x 680
191
SIK 16ME 353000
15.8 / 4.2 (4.0) 203
SIK 7TE 352810
6.9 / 4.3 (4.1)
3/N/PE ~400 V, 50 Hz
179
SIK 9TE 352820
9.2 / 4.4 (4.2) 180
SIK 11TE 352830
11.8 / 4.4 (4.2) 191
SIK 14TE 352840
14.5 / 4.5 (4.3) 203
Heat output and COP according to EN255 (EN 14511) at B0/W35 (B0 = brine inlet temperature 0 °C, W35 = heating water outlet temperature +35 °C) .
With borehole heat exchangers, the free compression values in the device information are to be adhered to (max. heat exchanger depth
at DN 32: 80 m)!
SIK 11ME 352990 4015627352995
SIK 16ME 353000 4015627353008
SIK 7TE 352810 4015627352810
SIK 9TE 352820 4015627352827
SIK 11TE 352830 4015627352834
SIK 14TE 352840 4015627352841
Max. flow temperature for heating 70 °C
Casing colour white
High-temperature brine-to-water heat pump
Compact design with high coefficients of performance
SIKH 6/9TE
Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design
screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD). Integrated brine compo-
nents enable direct connection of the heat source:
• Brine circulating pump (note the free compression)
• Expansion vessel (8 l)
• Safety valve and pressure manometer
Sound-optimised through insulated metal casing and double vibration-isolated compressor. Integrated solid-borne sound insulation for
direct connection to the heating system. High COPs through economiser and compliance with the requirements of EN 14511 for larger
volume flows on the heat consumption side. Compact design with optional domestic hot water preparation and integrated components
for direct connection of an unmixed heating circuit (must not be used for bivalent systems):
• Heat circulating pump (note the free compression)
• Overflow valve and safety module
• Expansion vessel (24 l)
Soft starter (from SI(K) 9 upwards), integrated flow and return sensors; external sensor (standard NTC-2), dirt filter and large-capacity
breather (1½“) with micro air bubble deposition for brine circuit included in the scope of supply.
Lower operating limit heat source (heating operation) -5 °C ; Upper operating limit heat source (heating operation) 25 °C ; Refrigerant
R134a ; Connection heating 1¼ ⬙ ; Heat source connection 1¼ ⬙.
Order reference Art.-Nr. Heat output with 1 compressor /
COP B0/W35
Connection voltage Width x Height x
Depth
mm
Weight
kg
SIKH 6TE 356070
6.4 / 4.7 (4.5)
3/N/PE ~400 V, 50 Hz 652 x 1115 x 688
180
SIKH 9TE 356080
9.4 / 4.7 (4.5) 203
Heat output and COP according to EN255 (EN 14511) at B0/W35 (B0 = brine inlet temperature 0 °C, W35 = heating water outlet temperature +35 °C).
phase out
The maximum flow temperatures (up to 70 °C) are available for DHW preparation all y
ear round, and allow DHW temperatures of up to 60 °C to be
achieved without electrical reheating using a flange heater.
SIKH 6TE 356070 4015627356078
SIKH 9TE 356080 4015627356085
Heat pump for heating purposes – ground source