Technical data

www.dimplex.de/en
23
2010
Max. flow temperature for heating 75 °C
Casing colour white
High-temperature air-to-water heat pump
Universal design with low- and high-temperature levels
LIH 22/26TE
Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design
screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD). The integrated air flow
enables corner or wall installation with air ducts at the air intake and the air outlet side. Sound-optimised through low-noise axial-flow
fan and vibration-isolated compressor. High coefficients of performance using an evaporator optimised for heating operation and
energy-efficient defrosting by reverse circulation. Universal design with low-temperature and high-temperature levels, optional DHW
preparation and the possibility of flexible expansion for:
• Bivalent or bivalent-renewable operating mode
• Distribution systems with unmixed and mixed heating circuits
In the summer a maximum heating flow temperature of 58 °C is available for domestic hot water preparation. Integrated soft starter, flow
and return-flow sensors; external sensor (standard NTC-2) included in the scope of supply.
Lower operating limit heat source (heating operation) -25 °C ; Upper operating limit heat source (heating operation) 35 ° C ;
Refrigerant R404A ; Refrigerant R134a ; Connection heating 1¼ ⬙ ; Connection voltage 3/N/PE ~400 V, 50 Hz
Order reference Art.-Nr. Heat output with 1 compressor /
COP A2/W35
Heat output with 2 compressors
/ COP A-7/W45
Width x Height x
Depth
mm
Weight
kg
LIH 22TE 352730
13.6 / 3.1 (3.0) 13.5 / 2.1
750 x 1710 x 1030
370
LIH 26TE 352740
15.9 / 3.2 (3.0) 15.2 / 2.2 377
Heat output and COP according to EN 255 (EN 14511) at A2/W35 (A2 = air intake temperature +2 °C, W35 = heating water outlet temperature +35 °C).
Heat output with 2 compressors and COP acc. to EN 14511 at A-7/W45 (A-7 = air intake temp. -7 °C, W45 = heating water outlet temp. +45 °C)
The maximum flow temperature of 75 °C is reached at an air intake temperatur
e from -25° C to +10° C (high-temperature level).
At outdoor temperatures above 10 °C, the maximum flow temperature is +58 °C (low-temperature level) .
LIH 22TE 352730 4015627352735
LIH 26TE 352740 4015627352742
Max. flow temperature for heating 58 °C
Casing colour white
Low-temperature air-to-water heat pump
for wall installation with two performance levels
LI 40AS
Heat pump for heating purposes for indoor installation with wall-mounted WPM 2006 plus heat pump manager and two compressors
for output reduction when operating at partial load. The air is drawn in via the heat pump installed directly in front of the wall. The air
circuit on the air outlet side is established via air ducts. Sound-optimised through low-noise, low-speed axial-flow fan and encapsulated
compressor housing; energy-efficient defrosting by reverse circulation. High COPs through high-performance evaporator and compli-
ance with the requirements of EN 14511 for larger volume flows on the heat consumption side. Universal design with two compressors
for modulating operation, optional DHW preparation and the possibility of flexible expansion for:
• Bivalent or bivalent-renewable operating mode
• Distribution systems with unmixed and mixed heating circuits
Integrated soft starter and flow sensors; return flow and external sensors (standard NTC-2) included in the scope of supply.
Electrical connection line EVL 996-1 (10m) between heat pump and heat pump manager included in the scope of supply.
Lower operating limit heat source (heating operation) -25 °C ; Upper operating limit heat source (heating operation) 35 ° C ;
Refrigerant R404A ; Connection heating 1½ ⬙ ; Connection voltage 3/N/PE ~400 V, 50 Hz
Order reference Art.-Nr. Heat output with
1 compressor /
COP A2/W35
Heat output with
2 compressors /
COP A2/W35
Air outlet Width x Height x
Depth
mm
Weight
kg
LI 40AS 358300
17.1 / 4.0 (3.9) 30.4 / 3.9 (3.8) fan side 1735 x 2100 x 890 590
Heat output and COP according to EN 255 (EN 14511) at A2/W35 (A2 = air intake temperature +2 °C, W35 = heating water outlet temperature +35 °C) .
LI 40AS 358300 4015627358300
Heat pump for heating – air source – indoor installation