Product Range Overview 2010 Renewable Energies Heat Pumps Solar Thermal Systems Domestic Heating Products 2010 Heatpumps Solar Thermal Systems Domestic Heating Systems
Contents Heat pump for heating purposes – air source – outdoor installation High-efficiency air-to-water heat pump package solution...................................................................................................................... 4 High-efficiency air-to-water heat pump ......................................................................................................................................................... 5 Air-to-water heat pump package solution ............................
Heat pump for heating purposes – air source – outdoor installation High-efficiency air-to-water heat pump package solution Heating and domestic hot water preparation package Max. flow temperature for heating 58 °C Casing colour white aluminium Heat pump and HWK 332 Econ hydro tower HPL..TUW The Hydro Tower with integrated WPM EconPlus regulation enables the fast and simple connection of an air-to-water heat pump installed outdoors to a heating system with an unmixed heating circuit.
Heat pump for heating purposes – air source – outdoor installation High-efficiency air-to-water heat pump High-efficiency air-to-water heat pump LA9TU Max. flow temperature for heating 58 °C Casing colour white aluminium Heat pump for heating purposes for outdoor installation with wall-mounted WPM EconPlus heat pump manager.
Heat pump for heating purposes – air source – outdoor installation High-efficiency air-to-water heat pump Max. flow temperature for heating 60 °C Casing colour white aluminium with two performance levels LA60TU Heat pump for heating purposes for outdoor installation, with wall-mounted WPM EconPlus heat pump manager and two compressors for output reduction when operating at partial load.
Heat pump for heating purposes – air source – outdoor installation Pipe assembly for high-efficiency air-to-water heat pumps for connection from the side The pipe assembly, which can be screwed directly onto the heat pump, consists of two pipes which are specially curved and matched to the high-efficiency air-to-water heat pumps; these pipes have connecting flanges for the connection to the heating water system.
Heat pump for heating purposes – air source – outdoor installation Four-way reversing valve Special hydraulic accessories for cooling The four-way reversing valve (1¼⬙ internal thread and/or 1½⬙ internal thread) for integration into the heating flow allows optimised heating and cooling operation of the LA 35TUR+ reversible air-to-water heat pump. Switching takes place via an electromotive actuator (essential accessory) which is activated by the WPM EconR heat pump manager.
Heat pump for heating purposes – air source – outdoor installation Air-to-water heat pump package solution Heating package Heat pump and HPK 200S hydraulic tower HPL... The hydraulic tower (W = 680 mm; H = 1660; D = 775) with integrated WPM 2006 plus controller enables the fast and simple connection of an air-to-water heat pump (installed outdoors) to a heating system with an unmixed heating circuit.
Heat pump for heating purposes – air source – outdoor installation Hydro tower with external heat pump manager Compact installation for heating and domestic hot water preparation HWK332 The hydro tower enables the fast and simple connection of a heat pump for heating purposes to a heating system with an unmixed heating circuit.The heat pump manager included in the scope of supply of the heat pump is used for the electronic control of the components (external wiring required).
Heat pump for heating purposes – air source – outdoor installation Air-to-water heat pump for free-standing installation Low-temperature air-to-water heat pump Max. flow temperature for heating 55 °C Casing colour white aluminium for free-standing installation Air-to-water heat pumps for outdoor installation with external temperature controlled WPM 2006 plus heat pump manager. Sound-optimised through the use of low-noise crescent wing axial-flow fans and deflector hoods.
Heat pump for heating purposes – air source – outdoor installation Reversible air-to-water heat pump Max. flow temperature for heating 58 °C Flow temperature cooling min. 7 °C Casing colour white aluminium Optimised for heating operation with waste heat recovery LA11ASR Air-to-water heat pump for outdoor installation with external temperature controlled heat pump manager WPM 2006 R and reversible refrigerating circuit for heating and cooling.
Heat pump for heating purposes – air source – outdoor installation Medium-temperature air-to-water heat pump Max. flow temperature for heating 65 °C Casing colour white aluminium for free-standing installation Medium-temperature air-to-water heat pumps for outdoor installation with external temperature controlled WPM 2006 plus heat pump manager. Sound-optimised through the use of noise-reducing crescent wing axial-flow fans and air deflector hoods; energy-efficient hot gas defrosting.
Heat pump for heating purposes – air source – outdoor installation Special accessories for air-to-water heat pump installed outdoors Electric connecting line heat pump – heat pump manager Control line between the heat pump manager and the air-to-water heat pump for outdoor installation. Wired ready for use and with coded plug connections at both ends for installation in a protective tube (min. diameter 70 mm, non-confusable: Round plug for connection to the heat pump). EVL ... Order reference Art.-Nr.
Heat pump for heating purposes – air source – outdoor installation Connection heat pump – heating water connection line Optimised for connection to a heat pump VSF.. Flexible hose connection set, length 250 mm, for fast and simple connection of an air-to-water heat pump (installed outdoors) to a heating water connection line laid under the ground. Consists of two insulated stainless steel Wellflex pipes with cap nuts and screw connections. Order reference Art.-Nr.
Heat pump for heating purposes – air source – outdoor installation Special accessories cooling regulation Room climate control station for temperature and humidity measurement This accessory is essential for silent cooling using panel heating/cooling systems. Connection to a cooling controller to control the flow temperature based on the measured room temperature and humidity via a reference room. RKSWPM Order reference Art.-Nr.
Heat pump for heating purposes – air source – outdoor installation Air-to-water heat pump with simplified regulation Air-to-water heat pump with simplified controller Max. flow temperature for heating 58 °C Casing colour white aluminium Compact design LAK10M Air-to-water heat pumps for close-to-wall outside installation and integrated heat pump control.
Heat pump for heating purposes – air source – outdoor installation Air-to-water swimming pool heat pump Air-to-water swimming pool heat pump Casing colour white aluminium with titanium heat exchanger Air-to-water heat pump for outdoor installation for heating swimming pool water.
Heat pump for heating – air source – indoor installation Air-to-water heat pump with 90° air deflection Low-temperature air-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Compact design LIK8TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating – air source – indoor installation Low-temperature air-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design LI9TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating – air source – indoor installation Air-to-water heat pump with straight air flow Low-temperature air-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating – air source – indoor installation Reversible air-to-water heat pump Optimised for heating operation with waste heat recovery LI11/16TER+ Max. flow temperature for heating 58 °C Flow temperature cooling min. 7 °C Casing colour white Heat pump for heating and cooling for indoor installation with integrated WPM 2007 R controller.
Heat pump for heating – air source – indoor installation High-temperature air-to-water heat pump Max. flow temperature for heating 75 °C Casing colour white Universal design with low- and high-temperature levels Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating – air source – indoor installation Special accessories for air-to-water heat pump installed indoors Airducts Optimally suited for air-to-water heat pump air circuits; GFRC exterior; thermally insulated and sound-insulated on the inside to prevent the formation of condensate and considerably reduce sound transmission. The ducts must be protected against driving rain and can, if necessary, be cut to length and/or painted with waterproof emulsion paint on site.
Heat pump for heating – air source – indoor installation Air duct hose set Air circuit for internally installed air-to-water heat pumps for use in rooms with low temperatures and low humidity. The set contains a 5m length of thermally-insulated and sound-insulated air hose which can be used for both the air intake and the air outlet side. The air intake and air outlet can be established via a light well or wall opening which must be constructed and insulated on site.
Heat pump for heating – air source – indoor installation Special accessories cooling regulation Room climate control station for temperature and humidity measurement This accessory is essential for silent cooling using panel heating/cooling systems. Connection to a cooling controller to control the flow temperature based on the measured room temperature and humidity via a reference room. RKSWPM Order reference Art.-Nr.
Heat pump for heating purposes – ground source Package solution for brine-to-water heat pump in compact design Heating and domestic hot water preparation package Heat pump and WWSP 229E built-under hot water cylin- HPK..TEW Max. flow temperature for heating 58 °C Casing colour white Consisting of compact brine-to-water heat pump, WWSP 229E built-under hot water cylinder and connection set for quick and easy connection of the individual components to the heating system.
Heat pump for heating purposes – ground source Passive cooling station for WPM EconPlus Passive cooling station Module for passive cooling via borehole heat exchangers. Consisting of heat exchanger, brine circulating pump, temperature sensor, passive cooling controller and enclosed 3-way distribution valve (DN25) with electrothermal actuator. Cooling operation mode is added to the existing heat pump manager by an electronic connection between the heating and cooling controller.
Heat pump for heating purposes – ground source Domestic hot water preparation for compact brine-to-water heat pump Supplementary package for DHW preparation Hot water cylinder The 400 l hot water cylinder is heated by the heat pump for heating purposes and offers convenient hot water preparation, also during longer shut-off times. It matches the height and design of the compact brine-to-water heat pump with built-under buffer tank. Order reference WWSP TE HPK(H) ... WWSP 442E Art.-Nr.
Heat pump for heating purposes – ground source Brine-to-water heat pump in a compact design Low-temperature brine-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Compact design SIK7TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground source Design tank for compact brine-to-water heat pump Design built-under buffer tank Nominal content 100 l; in brine-to-water heat pump design to enable space-saving installation on top of the built-under buffer tank; polyurethane insulation for minimal downtime losses (can be used for heating and cooling); 1½“ bush for immersion heaters (up to CTHK 635); 1¼“ heating water connections; colour: white; brown red design screen. PSP100E Order reference Art.-Nr.
Heat pump for heating purposes – ground source Brine-to-water heat pump in universal design Low-temperature brine-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design SI5TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground source High-temperature brine-to-water heat pump Max. flow temperature for heating 70 °C Casing colour white Universal design with high coefficients of performance SIH6TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground source Low-temperature brine-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design SI22TU Heat pump for heating purposes for indoor installation with integrated WPM EconPlus. Variable connection options for brine and heating connections on the rear wall of the casing. Integrated solid-borne sound insulation for direct connection to the heating system.
Heat pump for heating purposes – ground source Low-temperature brine-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design with two performance levels SI24-37TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground source Low-temperature brine-to-water heat pump Max. flow temperature for heating 58 °C Casing colour white Universal design with two performance levels SI50-130TE Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground source Brine package for brine-to-water heat pump with two performance levels Brine accessory package for ground heat collectors consisting of membrane safety valve, large-capacity breather with micro air bubble deposition, low-noise brine circulating pump with flange connection, manometer, expansion vessel, cap valve, ball valves, couplings and seals. SZB:Breather Order reference Art.-Nr.
Heat pump for heating purposes – ground source Special accessories for brine-to-water heat pump Connection package brine manifold The AP SVT connection package makes the connection of a maximum of 8 circuits possible. The AP SVT 16 connection package makes the connection of a maximum of 2 x 8 circuits possible using a tee joint. APSVT Order reference Art.-Nr.
Heat pump for heating purposes – ground water source Water-to-water heat pump Water-to-water heat pump Max. flow temperature for heating 55 °C Casing colour white with stainless steel coil heat exchanger Heat pump for indoor installation with integrated regulation WPM 2007 plus. The control panel is integrated into a brown-red design screen and can also be used as wired remote control using the wall mounting set (special accessories MS PGD).
Heat pump for heating purposes – ground water source Package solutions for brine-to-water heat pumps for using ground water as a heat source Low-temperature brine-to-water heat pump package Max. flow temperature for heating 60 °C Casing colour white Using ground water as a heat source The package solution for indirect use of water as a heat source with intermediate heat exchanger and brine-to-water heat pump (intermediate circuit with monoethylene glycol).
Heat pump for heating purposes – ground water source Special accessories for water heat source Plate heat exchanger for the use of polluted heat sources Screwed stainless steel plate heat exchanger. Max. operating pressure 10 bar, max. temperature 80 °C. Intermediate heat exchanger for polluted heat sources or heat sources with poor water quality. Connection for the cold and warm side with external thread, exception: WTE 130 – connecting flange with rubber bushing. WTE 20 Order reference Art.-Nr.
Heating and cooling – ground / ground water as heat source Passive cooling with brine-to-water or water-to-water heat pump Passive cooling station with cooling controller PKS.. Module for passive cooling via borehole heat exchangers.Consisting of heat exchanger, brine circulating pump, temperature sensor, passive cooling controller; 3-way distribution valve with electrothermal actuator included in the scope of supply.
Heating and cooling – ground / ground water as heat source Active cooling with brine-to-water heat pump Reversible brine-to-water heat pump Max. flow temperature for heating 58 °C Flow temperature cooling min. 7 °C Casing colour white Optimised for cooling operation SI11MER Heat pump for heating and cooling with integrated regulation installed indoors. Variable connection options for brine and heating connections on the rear wall of the casing.
Heating and cooling – ground / ground water as heat source Reversible brine-to-water heat pump Max. flow temperature for heating 58 °C Flow temperature cooling min. 7 °C Casing colour white Optimised for heating and cooling with waste heat reco- SI130TUR+ Heat pump for heating and cooling with integrated regulation installed indoors. Variable connection options for brine and heating connections on the rear wall of the casing.
Heating and cooling – ground / ground water as heat source Special accessories cooling regulation Room climate control station for temperature and humidity measurement This accessory is essential for silent cooling using panel heating/cooling systems. Connection to a cooling controller to control the flow temperature based on the measured room temperature and humidity via a reference room. RKSWPM Order reference Art.-Nr.
Accessories for heat pump for heating purposes Buffer tanks and accessories Built-under buffer tank Order reference PSP100E PSP100E PSP140E Art.-Nr.
Accessories for heat pump for heating purposes Immersion heater For electrical supplementary heating in mono-energy operation; consisting of individual heating elements with temperature controller, safety temperature limiter, degree of protection IP 54, 1½” external thread with plastic cover, fulfils the requirements of EN 60335, Part 1. Not suitable for enamelled steel hot water cylinders. CTHK ... Order reference Art.-Nr. CTHK 630 363610 CTHK 631 336180 CTHK 632 335910 2.9 CTHK 633 322140 4.
Accessories for heat pump for heating purposes Hot water cylinders and accessories Hot water cylinder with foil cladding and temperature sensor Steel cylinder (special inside enamelling) with protection anode and 3 supporting feet, polyurethane insulation with minimal stand-by losses, temperature sensor for connection to the heat pump manager included in the scope of supply, colour white, heating connection 1¼“, hot water connection 1“ external thread, circulation connection “.
Accessories for heat pump for heating purposes Design hot water cylinder Nominal content 400 l, in brine-to-water heat pump design, tube heat exchanger (internal), three supporting feet, steel cylinder (special inside enamelling) with protection anode, polyurethane insulation with minimal stand-by losses (approx. 2.7 kWh/24 h), integrated temperature sensor for connection to the heat pump manager, colour white, brown red design screen. WWSP 442E Order reference Art.-Nr.
Accessories for heat pump for heating purposes Hydro tower / combination tank Hydro tower with external heat pump manager Compact installation for heating and domestic hot water preparation HWK332 The hydro tower enables the fast and simple connection of a heat pump for heating purposes to a heating system with an unmixed heating circuit.The heat pump manager included in the scope of supply of the heat pump is used for the electronic control of the components (external wiring required).
Accessories for heat pump for heating purposes Heat pump/solar combo tank Combo tank for the integration of solar energy DHW heating in flow principle PWD750 Floor-mounted cylinder for heating and domestic hot water preparation with central flow, with three internally tin-plated heat exchangers (external pipework necessary); consisting of a buffer tank for heating and a buffer tank for DHW; heating buffer tank used as a preheating stage for DHW preparation.
Accessories for heat pump for heating purposes Distribution system for heat pumps Module for connecting the buffer tank and ensuring the heating water flow KPV with UP 60 EBKPV DDV.. Compact manifold Combinable module with insulation jackets for installation-friendly connection of the heat pump, buffer tank, hot water cylinder and hot water distribution system.
Accessories for heat pump for heating purposes Electronic circulating pump for consumer circuit UPE60 Electronically controlled circulating pump UPE 60 Electronically-controlled heat circulating pump with integrated flexible capacity via freely-adjustable rotational speed, micrometer 180 mm, low energy consumption thanks to energy efficiency class A (fulfils the requirements of EnEV, §14 (3)), automatic lowering of temperature at night, type of regulation (controlled or constant rotational speed) and the
Accessories for heat pump for heating purposes Domestic hot water preparation distribution system modules Hot water module Combinable module with insulation jackets for connecting DHW or swimming pool water preparation. Can be used for a heating water flow rate of up to 2.5 m³/h.
Accessories for heat pump for heating purposes Solar station for hot water Solar back-up for domestic hot water preparation Heat exchanger solar station consisting of solar separation system and pump assembly with insulation jackets for integrating solar installations up to 10 m² into the DHW heating system. The solar station enables efficient hot water heating via the heat pump as well as via the solar installation.
Accessories for heat pump for heating purposes Heat pump regulation and accessories Heating controller – heat pump manager Controller for the heat pump heating system for installation in frost-free rooms, with large back-lit LC display, time-controlled lowering and raising of the heating characteristic curves, time functions for DHW preparation according to need using the heat pump, with optional targeted reheating via flange heater.
Accessories for heat pump for heating purposes General accessories for the heat pump manager Order reference AP PGD Art.-Nr. Short text Features For connection to the wall-mounted WPM 2006 heat pump manager with integrated display or as an additional remote control for WPM 2007/ Remot e control for WPM 2006/2007/EconPlus/R EconPlus/R.The remote control has an LC-Display with identical menu navigation an backlightingl. The AWPM 900 connecting line must be ordered separately.
Fan convectors SmartRad fan convectors Fan convectors heating SmartRad Smart Rad fan convector with integrated electronic thermostat for mounting on the wall. Manual and automatic operation, maximum fan level can be preset; automatic regulation of fan level according to heat requirement. Water connection can be on the left or right. Heating and lowering times as well as frost protection can be individually adjusted using various RX programming cassettes which can be connected to the device.
Heat pump – air / waste heat as a heat source Heat pump module – heat source indoor air Air-to-water heat pump Max. flow temperature for heating 65 °C for utilisation of waste heat A heat pump module for utilisation of waste heat; integrated radial fan, exhaust and outgoing air stubs for optional connection of a duct system DN 160 (maximum length 10m), infinitely variable return set temperature.
Heat pump – air / waste heat as a heat source Hot water heat pump with sheet-steel casing Air duct connection and additional heat exchanger Hot-water temp. up to max.
Swimming pool dehumidifier Swimming pool dehumidifier SE...T Degree of protection IP 34 Lower operating limit heat source (heating operation) 15 °C Upper operating limit heat source (heating operation) 38 °C Cabinet unit for dehumidifying rooms with swimming pools in recirculating air operation with active heat recovery using the heat pump. The integrated control can be used to control the humidity and, depending on the scope of supply, the temperature.
Notes 62 www.dimplex.
Contents Solarthermie Solar collectors and accessories .......................................................................................................................................................................64 Solar hot water cylinders ....................................................................................................................................................................................66 Solar packages for domestic hot water preparation ..........................
Solar collectors and accessories Solar collector High-performance flat plate collector for mounting onto roofs and flat roofs or for free-standing installation, laser-welded full surface absorber with highly-selective coating. Collector for universal use can be used for larger surface areas as well as for single mounting. The connections make fast and hydraulically safe mounting possible. System is operated with pre-mixed SOLHT 20 solar fluid, providing the required frost protection.
Solar collectors and accessories Mounting accessories for SOLC 220 solar collectors Mounting set for roof mounting (pantiled roof, plain tile, corrugated sheet) and free-standing installation of SOLC 220 solar collectors. Consisting of the basic set for the first collector and an extension set for each additional collector. The sets include profile rails and stop anchors for collector mounting onto the respective type of roof as well as components for the hydraulic integration. Order reference Art.-Nr.
Solar collectors and accessories Solar hot water cylinders Solar hot water cylinders for heat pumps Solar domestic hot water cylinder made of steel (special enamelling inside) with protection anode, two internal bare-tube heat exchangers for solar and heating, thermometer, polyurethane insulation for minimal stand-by losses, colour white, TK150/DN110 flange. Permissible operating pressure 10 bar; Order reference WWSP 432 SOL Art.-Nr.
Solar packages for domestic hot water preparation Solar package with 2 collectors Solar package with 2 collectors for hot water preparation for a household of 2 – 4 people. • 1 x SOLCU 180 solar controller • 1 x SOLCU 1 solar controller • 1 x SOLPU S solar station • 1 x SOLHT 20 heat carrier fluid • 1 x SOLVK 1 expansion vessel connection • 1 x basic set for collector installation • 1 x SOLEV 12 expansion vessel • 1 x expansion set for collector installation SOLP 2 ... Order reference Art.-Nr.
Solar packages for supplementary heating and domestic hot water preparation Solar package with 5 collectors Solar package with 5 collectors for hot water preparation and supplementary heating. • 5 x SOLC 220 solar collector • 1 x SOLCU 1 solar controller • 1 x SOLPU V solar station • 2 x SOLHT 20 heat carrier fluid • 1 x SOLVK 1 expansion vessel connection • 1 x basic set for collector installation • 1 x SOLEV 35 expansion vessel • 4 x expansion set for installation SOLP 5 ... Order reference Art.-Nr.
Contents Storage heaters Dimplex storage heaters .....................................................................................................................................................................................70 PERMATHERM® storage heaters .......................................................................................................................................................................74 Accessories ....................................................................
Storage heaters Dimplex storage heaters ThermoComfort duo-electronic storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Compact design VFDi...C • Digital electronic duo charge controller with 2 control inputs for optional connection to DC charge controls (0.91–1.
Storage heaters ThermoComfort storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Compact design VFMi ...
Storage heaters ThermoComfort duo-electronic storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Slim Line Casing FSD...C • With wall bracket for mounting on load-bearing brickwork included as standard • Digital electronic duo charge controller with 2 control inputs for optional connection to DC charge controls (0.91–1.
Storage heaters ThermoComfort duo-electronic storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Low series VNDi ... C • Digital electronic duo charge controller with 2 control inputs for optional connection to DC charge controls (0.91–1.
Storage heaters ThermoComfort duo-electronic storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Hearth design • Can be integrated, mounted under a worktop or panelled with solid kitchen panelling • Digital electronic duo charge controller with 2 control inputs for optional connection to DC charge controls (0.91–1.
Storage heaters PERMATHERM® storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Slim Line Casing Optima • Storage heater in flat design • High-grade hard-shell core thermal insulation of natural vermiculite with Microtherm® • D ynamic discharge • Thermomechanical AC charge controller • AC control system 230 V AC, 80 % operating time ESF ... K Order reference Art.-Nr.
Storage heaters PERMATHERM® storage heaters Connection voltage 1/N/PE ~230 V, 50 Hz Two-circuit unit in slim line casing Optima ESFZ ...
Storage heaters PERMATHERM® storage heaters Connection voltage 3/N/PE ~400 V, 50 Hz Hearth design can be integrated • Hearth design can be panelled with solid kitchen panelling • High-grade hard-shell core thermal insulation of natural vermiculite with Microtherm® • D ynamic discharge • Thermomechanical AC charge controller • AC control system 230V AC, 80 % operating time • built-in room temperature controller Order reference ESK ... K with EZK ES Art.-Nr.
Storage heaters Integrated room temperature controller Order reference RTID 31 Art.-Nr. for device type 324530 VFDi 20C – VFDi 70C FSD 12C – FSD 48C VNDi 30C – VNDi 50C VTDi 45C – VTDi 75C RTID 31 / RTED 30 RTED 30 324520 RTEV 99 333990 VFDi...C & ESS...K FSD...C & ESF...K VNDi...C & ESN...K VTDi...C & EST...
Storage heaters Floor brackets For wall/floor mounting if the brickwork cannot bear loads and for free-standing installation. Painted profile angle with unscrewable ground support and fixing accessories. 10.4 cm ground clearance, (package contents: set = 2 items) Order reference Art.-Nr. Casing colour WKO 18 324470 FSD12C – FSD 48C bir ch grey EZ KK F IC251133 ESF12.. K – ESF 48..
Storage heaters Water-proofing kit Enables installation of storage heaters according to VDE regulations. Do not use in combination with special accessories for the integrated room temperature controller. Degree of protection IP X4 (splash water protection). WS 25 i Order reference Art.-Nr.
Storage heaters Components storage heaters Electronic charge controller Order reference Art.-Nr. Features LRD 2000 plus 338830 Digital electronic DC/AC charge controller with two control inputs for ThermoComfort duo-electronic VFDi..(C), VFD.., FSD..(C), VNDi..(C), VTDi..(C), and VKD.. storage heaters, optional connection to DC charge control (0.91–1.
Direct heating devices Radiant panel heater FPE series Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 20 Protection class l horizontal model Wall mounting using wall bracket, connection cable for fixed connection, high-quality metal casing, aluminium surface heating element, electronic infinitely variable room thermostat, protection against overheating, function switch for ON / OFF/ Antifreeze / Lower. Lowering can be centrally regulated using an external regulator e. g.
Direct heating devices Design wall convector GFP series GFP 200 B Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP X4 Protection class l Design convector with precise electronic room temperature regulation, infinitely adjustable +5 °C to +30 °C, antifreeze setting, connecting lead for fixed connection, high-grade metal casing with easy-care glass front, ON/OFF switch, temperature lowering using a programming module or external control of the control line possible, e. g.
Direct heating devices Wall convectors EPX series Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP X4 Protection class l electronically regulated Precise electronic room temperature control, infinitely variable from 5 °C to 30 °C, antifreeze setting, connection cable for fixed connection, ON/OFF switch, temperature lowering using a programming module or external control of the control line e. g. timer or switch possible.
Direct heating devices Wall convectors DXW series Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 20 Protection class l Infinitely variable thermostat, fold-down wall bracket, sheet-steel casing, connection cable for fixed connection, ON/OFF switch, 2 heating levels, (DXW 315 to DXW 330). Order reference DXW 330 Art.-Nr.
Direct heating devices Towel dryer/bathroom fan heater TRFB Connection voltage 1/N ~230 V, 50 Hz Degree of protection IP 24 Protection class ll Combination of radiant panel heater, towel dryer and bathroom fan heater, electronic room thermostat, electronic timer for ventilation operation 0. 5 hour / 1. 0 hour / 2.
Direct heating devices Unique wall convectors Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 24 Protection class l To be mounted using a wall bracket with outlet for fixed connection, electronic thermostat, lowering using control line or radio module, high-quality aluminium finned heating element, galvanised and powder-coated casing, colour white similar to RAL 9010, On/Off switch. Order reference Art.-Nr.
Direct heating devices Radiant panel heaters Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 21 Protection class l Flat radiators with encapsulated tubular radiator for a uniform surface temperature and heat transfer as radiant heat, electronic room thermostat with temperature lowering using a control line or an optional radio module, controlling range 5 °C to 30 °C, antifreeze setting, wall bracket with outlet, connected with a fixed connection, ON / OFF switch, powder-coated casing, col
Industrial heaters Industrial fan heaters IHP series Degree of protection IP 24 Protection class l portable Fan heaters in metal design with carrying handle for portable use. Controls integrated directly in the device, room temperature control with antifreeze setting, wall mounting using the accompanying wall bracket in not easily reachable heights possible. Casing colour blue, air outlet grid black. IHP30 Order reference Art.-Nr.
Hot-aircurtain Air Curtains AC...N series Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 20 Protection class l Electric operation Mounting above doors or on ceilings, adjustable air output direction, 2 heating levels, 1 cold air level. Controllable on the device itself or with a remote control (only AC 3RN) only. Door width covered adjustable from 600 mm (AC 3 and AC 45) to 900 mm (AC 6). Rated power W Air volume flow m3/h Max.
Hot-aircurtain Air barrier DAB series Connection voltage 1/N/PE ~230 V, 50 Hz Protection class l hot water operation DAB 10 W V2 DHW operation, mounting above doors, on ceilings or hidden (optional installation kit needed), modular design allows simple placing of devices in a row, mounting height up to 4. 0 m, adjustable direction of flow, 2 ventilator levels, controllable using wall-mounted lowvoltage control or by connecting to a building management system.
Handdryer Handdryer Order reference HD 701 AM HD 701 AM HD 601 AM Art.-Nr. Rated power W Width x Height x Depth mm Weight kg Robust metal casing with epoxy coating, colour white, similar to RAL 9010, infrared safety proximity switch with adjustable sensitivity, rated air flow 470 m3/h with approx. 96 km/h, air outlet temperature approx.
AKO direct heating devices Radiant panel heaters WW... series Connection voltage 1/N ~230 V, 50 Hz Degree of protection IP 24 Protection class ll Free-standing installation on casters, or wall-mounted. Metal heating plate, mech. thermostat, antifreeze, protection against overheating, indicator lamp for heating operation, colour white, splash water protection, TÜV GS certification. Order reference WW 150 Art.-Nr. Rated power W WW 100 AKO150611 1000 3performance levels: OFF / 0.65 / 1.
AKO direct heating devices Infrared heater (compact range) Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 24 Protection class l Infrared heaters (compact range) with quartz heating elements for horizontal wall mounting, switchable via a pull switch on the device, pivoting angle 0° – 40°, fixed connection, VDE certification. BS 1201 S BS 1801 S Order reference Art.-Nr.
AKO direct heating devices Patio radiators UWS 75 RD 1/E BA1200 Order reference UWS 75 RD 1/E Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP X4 Protection class l Art.-Nr. AKO106169 Rated power W 1300 2 BA1900 354870 354880 UWS 75 RD 1/E BA1200 1900 Patio radiator for horizontal wall or ceiling mounting, fixed connection, pivoting angle (one-sided) 25°, 3 control levels OFF / 0.65 / 1.3 kW, switching via an external switch (e.g.
AKO direct heating devices Design fan heaters Order reference H401 TSD Connection voltage 1/N ~230 V, 50 Hz Degree of protection IP 20 Protection class ll Art.-Nr. 2000 H400 TS 352580 352570 Art.-Nr. SH302 TLU AKO151156 SH301 TLS AKO151151 Features Rated power W 1.4 Width x Height x Depth mm Wall-mounted or floor-mounted fan heater with axial fans, carrying handle/recess, cable compartment, 24-hour timer, thermostat, antifreeze, cold air level, indicator lamp, five levels OFF/ Cold / 0.
Floor heating systems Under tile heating mats HM...TS Connection voltage 1/N/PE ~230 V, 50 Hz with single-sided, sleeveless connection, self-adhesive Ready for installation and connection, heating pipe with protective jacket for connecting to the fault current protective switch, heating pipe made of resistance alloy according to DIN 17470 and/or DIN 17471 with teflon insulation, surface-related consumption 150 W/m2, heating pipe diameter approx.
Floor heating systems Under tile mats set HM…TS set BT Connection voltage 1/N/PE ~230 V, 50 Hz with floor temperature controller BT 401 UN HM ... TS Set BT Ready for installation and connection, heating pipe with protective jacket for connecting to the fault current protective switch, heating pipe made of resistance alloy according to DIN 17470 and/or DIN 17471 with teflon insulation, surface-related consumption 150 W/m2, heating pipe diameter approx.
Floor heating systems Floor heating mats HM … R for installation in or under Connection voltage 1/N ~230 V, 50 Hz concrete For use as underfloor direct heating, underfloor storage heating or edge zone direct heating with PVC outer surface, manufactured ready for mounting, fixed to a carrier netting for installation in/under the screed, heating pipe diameter approx. 7 mm. including waterproof sleeves and colour-coded cooling pipes 4m per side, heating pipe design: NH2GMY-90 according to VDE 0253/12.
Floor heating systems Floor heating mat HM...
Trace heating Self-regulating electric band heaters – per metre Connection voltage 1/N/PE ~230 V, 50 Hz Gutter heater or pipe trace heater made of self-limiting electric band heater, used for frost protection on (vertical) pipes, in gutters or on roof surfaces. Made of two parallel tin-plated stranded copper wires and an intermediate heating element, protective jacket of tin-plated copper, polyolefin outer surface, VDE certification. Different heat output and operating range, depending on the design.
Control and regulation devices Control and regulation devices for electric band heaters and exterior surface heating Electronic ice and snow detector Order reference EM1773 EM1773 Art.-Nr. 361710 Digital ice and snow detectors for use in combination with one or two combined humidity and temperature sensors (type EF 3354 / EF 3351) for gutters, flat roofs and parabolic aerials.
Control and regulation devices DC charge controls for storage heating systems Universal DC charge control with timer function Control voltage 1 0.91 to 1.43 V Control voltage 2 -3,6 to -2,85 V Dimplex PROTOMATIK ® ZW05DCU Universal DC microprocessor-driven charge control with timer function for backward, intermediate and forward control, two control voltage outputs 0.91 to 1.43 V DC and –3.6 to –2.
Control and regulation devices AC charge controls for storage heating systems AC charge control with timer function Control voltage 1 ~230 V Operating time system 37 % – 80 % adjustable Dimplex PROTOMATIK ® ZWM05AC For storage heaters with thermomechanical AC charge controller and duo-electronic storage heaters.
Control and regulation devices Room temperature controller Order reference Art.-Nr. Features 355480 Electromechanical temperature controller (bimetal) with thermal feedback, switching capacity 230 V / 2 (1) A, IP 30, controlling range 5 °C to 30 °C, temperature lowering at night by remote control (approx. 4 K), extremely thin casing, colour alpine white, temperature range limitation in the casing cover, surface mounting.
Control and regulation devices Room temperature controller with plug Order reference Art.-Nr. RT 104 ST 348180 Features Width x Height x Depth mm Plug thermostat (bimetal) suitable for plugging into a socket, controlling range 5 °C to 30 °C, temperature range limitation in the casing cover, switching capacity 250V AC / 13 (4) A, max.
Control and regulation devices Integrated room temperature controller Order reference RTID 31 Art.-Nr. for device type Features Integrated electronic speed controller (wave packet control), complete kit, can be plugged into the duo charge controller, with switch for “lowering the temperature at night” and switch for “supplementary heating” with control lamps, control panel in control recess, 230 V / 60 VA (fan) / 10 A (supplementary heating), controlling range 8 °C to 30 °C.
Control and regulation devices Floor temperature controller with timer Order reference BTU 401 UN Art.-Nr.
Control and regulation devices Heating/cooling ON/OFF room temperature controller In flat switch mounting frame for flush mounting Order reference RTK 601U Art.-Nr.
Domestic hot water devices Instantaneous water heater ecotronic Connection voltage 3/PE ~400 V, 50 Hz Degree of protection IP 25 Instantaneous water heater with electronic output adjustment, infinitely variable temperature setting via symbols using a rotary encoder. Bare wire heating system for instant DHW heating and high resistance to lime scaling. Reduced switch-on volume flow of 2.
Domestic hot water devices Compact hot water cylinder for mounting under a worktop Connection voltage 1/N/PE ~230 V, 50 Hz Degree of protection IP 24 Pressure-less design, temperature setting range 35 °C to 85 °C energy-saving and antifreeze settings, connection cable and plug, water connections metal 3/8“ thread, safety temperature limiter with reset function. Order reference ACK 5 U Art.-Nr.
Domestic hot water devices Single-circuit wall-mounted cylinder Degree of protection IP 24 Single-circuit wall-mounted cylinders for closed or open use, infinitely variable temperature adjustment from 25 °C to 85 °C, inner container made of steel with special enamelling, anti-corrosion bar (protection anode), CFC-free thermal insulation for minimal heat loss, three individual heating elements in an enamelled protection tube (can be replaced without emptying the device), sheet steel outer surface.
Index Type Order reference EAN code 2NC8 042 4X 2NC80424X 7036088801195 87 2NC8 062 2F 2NC80622F 7036088800648 87 2NC8 062 4B 2NC80624B 7036088801560 87 AWPM 900 2NC8 062 4F 2NC80624F 7036088800426 87 2NC8 102 2F 2NC81022F 7036088800662 87 B 2NC8 102 4B 2NC81024B 7036088801584 87 2NC8 102 4F 2NC81024F 7036088800440 87 2NC8 102 4S 2NC81024S 7036088801379 87 2NC8 152 2F 2NC81522F 7036088800686 87 BK 1201 S 356670 4015627356672 94 2NC8 152 4F 2NC81524F 7036088800
Index Type Order reference EAN code Page Type Order reference EAN code Page DRW 36NC 344440 4015627344440 80 ESFZ 3636 K IC260390 4021481260390 76 DRW 43NC 344450 4015627344457 80 ESK 2419 K IC251318 4021481259455 77 DRWi 20C 344370 4015627344372 80 ESK 2424 K IC251320 4021481259448 77 DRWi 30C 344380 4015627344389 80 ESN 3024 K IC251288 4021481259363 76 DRWi 40C 344390 4015627344396 80 ESN 3030 K IC251293 4021481259370 76 DRWi 50C 344400 4015627344402 80
Index Type Order reference EAN code Page Type Order reference EAN code Page FPE 101 H 348750 4015627348752 82 HM 1130 SF 150 326170 4015627326170 98 FPE 101 V 348780 4015627348783 82 HM 120 R 140 319280 4015627319288 99 FPE 151 H 348760 4015627348769 82 HM 120 R 160 327260 4015627327269 99 FPE 201 H 348770 4015627348776 82 HM 120 R 180 326690 4015627326699 99 FPE 201 V 348790 4015627348790 82 HM 120 RS 160 327310 4015627327313 100 FSD 12C/HS 1207 345430 401
Index Type Order reference EAN code Page Type Order reference EAN code Page L HPK 11TE 353440 4015627353442 28 HPK 11TEW 362610 4015627362611 27 LA 11AS 339950 4015627339958 11 HPK 14TE 353450 4015627353459 28 LA 11ASR 342730 4015627342736 12 HPK 7TE 353420 4015627353428 28 HPK 7TEW 362590 4015627362598 27 LA 11MAS 363760 4015627363762 10 HPK 9TE 353430 4015627353435 28 LA 11MS 342420 4015627342422 11 HPK 9TEW 362600 4015627362604 27 HPKH 6TE 356150 40
Index Type Order reference EAN code Page Type Order reference EAN code Page LKL 600 339740 4015627339743 24 R LKL 700 339770 4015627339774 24 RAR 20-90 316360 4015627316362 102 LKL 800 339800 4015627339804 24 RBG WPM 339700 4015627339705 57 LKL 900 358260 4015627358263 24 RBS 12U 358830 4015627358836 7 LR 100 338840 4015627338845 81 RBS 17U 358840 4015627358843 7 LR 90 338850 4015627338852 81 RBS 25U 358850 4015627358850 7 LRD 2000 plus 338830 40156273
Index Type Order reference EAN code SG 2 Page Type Order reference EAN code Page 326360 4015627326361 112 SOLCU 1 356220 4015627356221 65 SH 300 T AKO151146 4011652507621 96 SOLCU 2 356560 4015627356566 65 SH 301 TLS AKO151151 4011652507638 96 SOLEV 12 356240 4015627356245 65 SH 302 TLU AKO151156 4011652507645 96 SOLEV 18 356250 4015627356252 65 SI 100TE 352950 4015627352957 36 SOLEV 24 356980 4015627356986 65 SI 11ME 353040 4015627353046 32 SOLEV 35 356
Index Type Order reference EAN code Page Type Order reference EAN code Page TRFB 150 354900 4015627354906 86 VFMi 40C/HFi 425 345300 4015627345300 71 TRFW 101 348710 4015627348714 85 VFMi 40C/HFi 432 345310 4015627345317 71 TRFW 151 348720 4015627348721 85 VFMi 40C/HFi 440 345320 4015627345324 71 TRFW 201 348730 4015627348738 85 VFMi 40C/HFi 452 * 345330 4015627345331 71 TUE 430 337430 4015627337435 15 VFMi 50C/HFi 540 345340 4015627345348 71 TUE 440 337440
Index Type Order reference EAN code Page WPG 25 356030 4015627356030 54 WPG 32 356040 4015627356047 54 WPM 2006 plus 352550 4015627352551 56 WPM Econ PK 360000 4015627360006 42 WPM EconPlus 355950 4015627355958 56 WPM PK 348190 4015627348196 42 WS 25 i 328590 4015627328594 80 WSH 12 362120 4015627362123 6 WSH 25 358970 4015627358973 6 WSH 40 358240 4015627358249 6 Type WSH 9 362110 4015627362116 6 WSI 110TE 361580 4015627361584 40 WSI 150TE 361590 4015
Notes 2010 Sortimentsliste_GB_2010_121-122.indd 121 www.dimplex.de/en 121 15.11.
Notes 122 Sortimentsliste_GB_2010_121-122.indd 122 www.dimplex.de/en 2010 15.11.
Subject to colour deviations and technical modifications without notice · AU 11/10.1 · AKOM360 Munich · DIM 763V1 Visit www.dimplex.de and www.heating-with-heatpump.com for further up-to-date information Glen Dimplex Deutschland GmbH Dimplex Division Am Goldenen Feld 18 95326 Kulmbach, Germany Phone: +49 9221 709-201 Fax: +49 9221 709-233 09221709233@dimplex.de www.dimplex.
