PARTS & SERVICE MANUAL FOR THE CORNER WALL MOUNT FIREPLACE MODEL NUMBER: EWMC-CC-SS
TABLE OF CONTENTS OPERATION PAGE 1 PARTS LIST DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 LIGHT BULB REPLACEMENT PAGE 6 MAIN ON/OFF SWITCH REPLACEMENT PAGE 7 MANUAL SELECTION SWITCH REPLACEMENT PAGE 8 THERMOSTAT CONTROL REPLACEMENT PAGE 9 FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 10 HEATER ASSEMBLY REPLACEMENT PAGE 12 CIRCUIT BOARD REPLACEMENT PAGE 14 POWER CORD REPLACEMENT PAGE 16 MIRROR REPLACEMENT PAGE 18
EWMC-CC-SS OPERATION MANUAL CONTROLS The controls are located inside the door panel on the lower right hand side of the corner wall mounted electric fireplace. (FIGURE 1) A. MAIN POWER SWITCH The MAIN on/off switch supplies power to the circuit board. When the Main ON/OFF switch is switched to the ON position the Level 1 indictor light will flash. B A C FIGURE 1 Manual Selection Switch Main Power Switch Level 3 Indicator Level 2 Indicator Level 1 Indicator FIGURE 2 B.
EWMC-CC-SS REMOTE CONTROL The corner wall mounted electric fireplace is supplied with a radio frequency remote control. This remote control has a range of approximately 50 feet (15.25m), it does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with one of 243 independent frequencies to prevent interference with other units. The frequency designation is indicated on the back of the transmitter (FIGURE 3).
EWMC-CC-SS 18 2 15 16 1 17 8 12 5 14 6 7 13 11 10 4 3 9 3
EWMC-CC-SS REPLACEMENT PARTS CORNER WALL MOUNT FIREPLACE MOD. LEVEL REPLACEMENT PART 1. LOGSET ASSEMBLY 2. TOP ASSEMBLY 3. BASE ASSEMBLY 4. HEATER ASSEMBLY 5. THERMOSTAT 6. MANUAL SELECTION SWITCH 7. MAIN POWER SWITCH 8. WIRE ASSY LAMPHOLDER 9. REMOTE CONTROL 10. CIRCUIT BOARD 11. CORD SET 12. REFLECTOR ASSEMBLY 13. FLICKER MOTOR 14. FRONT GLASS 15. MIRROR 16. THERMOSTAT KNOB 17. LATCH DOOR ASSEMBLY 18.
EWMC-CC-SS WIRING DIAGRAM THERMOSTAT WHITE FLICKER MOTOR BLACK N WHITE I 0 0 II LEDs YELLOW I ORANGE MAIN SWITCH HEATER SWITCH BLUE MARR BLACK MARR RL1 5 AC120V RL2 RED WHITE ROUGH WHITE SMOOTH POWER CORD CIRCUIT BOARD RL3 BLACK BLACK BLACK BLACK BLACK WHITE WHITE BLOWER MOTOR GREEN LIGHT HARNESS WHITE RED ELEMENT BLACK
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are two bulbs under the log set which generate the flames and embers.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE MAIN POWER SWITCH 1. Open latched door. 2. Remove the 3 mounting bracket screws and set aside mounting bracket. 3. Remove the 2 log set screws and remove the log set. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE MANUAL SELECTION SWITCH 1. Open latched door. 2. Remove the 3 mounting bracket screws and set aside mounting bracket. 3. Remove the 2 log set screws and remove the log set. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE THERMOSTAT CONTROL 1. Remove unit from corner and lay unit on its side. 2. Open latched door. 3. Remove the 3 mounting bracket screws and set aside mounting bracket. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE FLAME MOTOR/FLAME ROD 1. Open latched door. 2. Remove the 3 mounting bracket screws and set aside mounting bracket. 3. Remove the 2 log set screws and remove the log set. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE FLAME MOTOR/FLAME ROD WARNING: Ensure wires do not come in contact with moving parts by securing wires in wiring tie wraps.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE HEATER ASSEMBLY 1. Remove the wall mounted unit from corner and lay unit on its side. 2. Open latched door. 3. Remove the 3 mounting bracket screws and set aside mounting bracket. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. Remove wall mounted unit from corner and lay unit on its side. 2. Open latched door. 3. Remove the 3 mounting bracket screws and set aside mounting bracket. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD NOTE: When installing the replacement circuit board ensure the red heat indicator lights are installed into their original mounting locations.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE POWER CORD 1. Remove wall mounted unit from corner and lay unit on its side. 2. Open latched door. 3. Remove the 3 mounting bracket screws and set aside mounting bracket. 4.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
EWMC-CC-SS If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE MIRROR 1. Remove wall mounted unit from corner and lay unit on its side. 2. Open latched door. 3. Remove door chain bolt and nut from back panel assembly. 4.
