Service Manual 30” Self Trimming Fireplace Purifire™ and Mid-line Remote Model Numbers: DF3015 - MOD / to C DFB8842 - MOD / REV Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www.dimplex.com In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
Table Of Contents Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 DF3015 Exploded Parts Diagram and Parts List. . . . . . . . . . . . . . . . . . . . . . . . Page 5 DF3015 Wiring Diagram and Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 DFB8842 Exploded Parts Diagram and Parts List . . . . . . . . . . . . . . . . . . . . . . . Page 7 DFB8842 Wiring Diagram and Schematic. . . . . . . . . . . . . . .
Operation 4. Replace the battery cover. The manual controls for the fireplace are located in the lower right hand corner (Figure 1). Figure 1 ! NOTE: When the “BAT” symbol is present on the remote control it is recommended to replace the batteries promptly, to maintain full functionality of the remote/ fireplace. The remote transmitter has a battery backup time of only several hours. A Figure 2 Batteries Child Lock Remote Control Initialization 1. Plug cord into a 120 Volt wall outlet. 2.
Remote Control Functions B I K M O Q A C D E F H function on. When the Purifire™ function is on, the Purifire™ symbol will flash. When off, the symbol will be solid. The default setting for the Purifire™ is set at low speed. Press the Q. Purifire™ Speed Down or the R. Purifire™ Speed Up buttons to change between low and high speeds. Press the G. Purifire™ On/Off button to turn the Purifire™ function off. J L H. Flame & Heat On/Off Button Press the H.
DF3015 Exploded Parts Diagram 15 4 3 13 9 12 14 10 5 1 7 16 6 2 11 Replacement Parts List DF3015 Part Number 6903020159 Replacement Part: 1. Log Set Assembly . . . . . . . . . . . . . . . . .0439070100RP 2. Flicker Motor . . . . . . . . . . . . . . . . . . . . 3000240200KIT 3. Heater Assembly . . . . . . . . . . . . . . . . .2200490600RP 4. Cutout . . . . . . . . . . . . . . . . . . . . . . . . . .2300270300RP 5. Main On/Off Switch . . . . . . . . . . . . . . . 2800070700RP 6.
Log Set Assembly Heater Assembly Cord Set 6 Flicker Motor Remote Control Receiver Main On/Off Switch DF3015 Wiring Diagram
DFB8842 Exploded Parts Diagram 8 17 15 14 4 2 3 9 6 7 5 13 16 10 12 11 1 Replacement Parts List DFB8842 Part Number 6903020359 Replacement Part: 1. Log Set Assembly . . . . . . . . . . . . . . . . .0438550100RP 2. Flicker Motor . . . . . . . . . . . . . . . . . . . . 3000240200KIT 3. Heater Assembly . . . . . . . . . . . . . . . . .2200490600RP 4. Cutout . . . . . . . . . . . . . . . . . . . . . . . . . .2300270300RP 5. Main On/Off Switch . . . . . . . . . . . . . . . 2800070700RP 6.
Heater Assembly Cord Set Flicker Motor Remote Control Receiver Main On/Off Switch DFB8842 Wiring Diagram 8
Front Glass Replacement Upper Bulb Replacement Procedure 1. 2. 3. 4. 5. If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Slide firebox out of mantel. Lay unit on it’s back for safe removal of Front Glass. Remove four (4) Phillips screws from right side of Trim. Remove Trim.
6. Pull the front edge of the plastic Ember Bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the Mirror (Figure 6). Figure 6 Mirror Replacement Log Ember Bed If the fireplace was operating prior to servicing allow at least five (5) minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
Main On/Off Switch and Remote Switch Board Replacement 11. To replace the Remote Switch Board, properly orientate the replacement board and re-attach to plastic switch housing using the two (2) screws removed in step 10. Re-assemble firebox following steps 1 through 9 in reverse order. To replace Main On/Off Switch, continue to step 12. 12. Remove the Main On/Off Switch by squeezing the two (2) retaining clips on either side of the switch and from within the firebox, then push out the front of the unit.
Figure 10 Support bracket ! NOTE: In the event that multiple Flicker Motors were already replaced within unit, or if required wiring has been cut too short, it may be necessary to replace Flicker Motor and the attached cable as a whole. To do so: i) Follow steps 1 through 12 and 14. ii) Follow steps 1 through 8 from Mirror Replacement procedure (page 8) to remove Mirror.
taken when handling the glass. Figure 12 6. Pull the front edge of the plastic Ember Bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the Mirror (Figure 6, page 8). Antenna wire Cable connector to upper and lower light harness ! IMPORTANT: Only handle the Log Set Assembly by the Ember Bed or plastic grate. ① 5 color cable to Flicker Motor ② ③ ! NOTE: Log Set Assembly fits tightly into firebox, some force may be necessary to remove. 7.
Figure 13 Heater Assembly Cutout and screw (1) iv) Referring to Figure 14, connect the new Cutout’s two (2) wires to the Remote Receiver board and Heater Element and Motor. v) Follow steps 1 through 3 in reverse order to reassemble firebox. 5. To replace Heater Assembly: i) Remove the one (1) small Phillips screw that attaches the Cutout to the Heater Assembly as shown in Figure 13 and stow Cutout safely aside. ii) Remove the Phillips retaining screw using a short handled driver.
14. Disconnect the black wire from the Remote Receiver board (Figure 15). 15. Using pliers, squeeze the sides of the plastic wire clamp on the Power Cord from inside the chassis and push it through the sheet metal. 16. Release clamp from the Power Cord and remove Power Cord from the firebox. 17. Run replacement Power Cord through the firebox as above and connect wire ends as described in Figure 15. 18 Leave two (2) inches of slack in cord and secure in place with clamp. 19.
