PARTS AND SERVICE MANUAL FOR DIMPLEX MULTIFIRE™ ELECTRIC FIREPLACE MODEL NUMBER: DF3015 Valued Customer, We are pleased that you have chosen to purchase an electric fireplace manufactured by Dimplex North America Ltd.Over the years, valuable memories will occur around the warmth and comfort of your hearth. Thank you for allowing our product to be the backdrop for those special moments.
TABLE OF CONTENTS OPERATION PAGE 2 PARTS DRAWING PAGE 7 PARTS LIST PAGE 8 LOWER LIGHT BULB REPLACEMENT PAGE 9 UPPER LIGHT BULB REPLACEMENT PAGE 10 MAIN ON/OFF SWITCH REPLACEMENT PAGE 11 SWITCH CIRCUIT BOARD REPLACEMENT PAGE 11 FLAME MOTOR/REFLECTOR ROD REPLACEMENT PAGE 12 HEATER ASSEMBLY REPLACEMENT PAGE 13 CIRCUIT BOARD REPLACEMENT PAGE 14 POWER CORD REPLACEMENT PAGE 15 1
DF3015 OPERATION ELECTRIC FIREPLACE MANUAL CONTROL The manual controls for the fireplace are located in the lower right hand corner. A. Main On/Off Switch Supplies power to the 3 position manual control switch. B. 3 Position Manual Control Switch Remote (right position): The unit is operated with the remote control. Flame (center position): The flame effect is turned ON. Flame & Heat (left position): The flame effect and heater are turned ON simultaneously.
CAUTION If you need to continuously reset the heater, unplug the unit and call Dimplex North America Limited at 1-800-668-6663 and press 4 for technical support. Please have your model and serial number ready when calling. REMOTE CONTROL The remote control has a range of approximately 50 ft. (15.25m), it does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with 243 independent frequencies to prevent interference with other units.
2. “COD” will appear in place of the sleep timer digits. 3. Release the “SLEEP TIMER DOWN” button and the “PURIFIRE LOW SPEED” button. 4. Press the initialization button on the unit. 5. press the button on the remote. Your remote will now have a different frequency communicating with the fireplace.
SET TEMPERATURE 1. Press “Flame Heat On/Off” button to turn fireplace on. 2. Press “Temperature Up” to raise thermostat. 3. Press “Temperature Down” to lower thermostat. 4. Press both “Temperature Up” and Temperature Down” to change °F to °C. FLAME SPEED 1. Press the “Flame/Heat On/Off” button to turn the Flame/Heat ON. 2. Press the “Flame Speed Up” to increase the speed of the flame. 3. Press the “Flame Speed Down” to decrease the speed of the flame. LIGHT DIMMER 1.
PURIFIRE™ The Purifire™ includes a high efficiency filter to help improve the quality of air. 1. Press the button for the Purifire™ function. 2. Press the “Purifire Low Speed” button or the “Purifire High Speed” button to select LOW or HIGH. 3. Press the OFF. button to turn the Purifire™ ON, press the button to turn the Purifire™ SLEEP TIMER The Sleep Timer automatically shuts off the fireplace after a preset time (from 30 minutes to 8 hours). 1.
DF3015 2 3 10 13 7 4 8 12 11 1 9 5 6 14 7 15
DF3015 REPLACEMENT PARTS FIREBOX, 30" - DIMPLEX CATALOGUE NO. PART NO. MOD LEVEL: MADE IN: DF3015 6903020159 NONE CHINA REPLACEMENT PART 1. 30” URETHANE LOG SET ASSEMBLY 2. HEATER ASSEMBLY 3. UPPER LIGHT HARNESS 4. LOWER LIGHT HARNESS (left and right bulbs) LOWER LIGHT HARNESS (center bulb) 5. FLAME MOTOR 6. REMOTE CONTROL – SENDER 7. REMOTE CONTROL RECEIVER 8. CORD SET 9. REFLECTOR ROD 10. MIRROR, SEMI-SILVERED 11. FRONT GLASS 12. FOOT 13. FILTER 14. MAIN ON/OFF SWITCH 15.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE MAIN ON/OFF SWITCH/SWITCH CIRCUIT BOARD 1. 2. 3. 4. Slide fireplace out of mantel 2-3 inches. Remove 4 Phillips screws from the right side of trim. Slide glass to right side of fireplace to remove.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/REFLECTOR ROD 1. 2. 3. 4. Slide fireplace out of mantel 2-3 inches. Remove 4 Phillips screws from the right side of trim. Slide glass to right side of fireplace to remove.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ASSEMBLY 1. 2. 3. 4. 5. 6. 7. 8. 9. Slide fireplace out of mantel 2-3 inches. Remove 4 Phillips screws from the right side of trim. Slide glass to right side of fireplace to remove.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. 2. 3. 4. 5. 6. 7. 8. 9. Slide fireplace out of mantel 2-3 inches. Remove 4 Phillips screws from the right side of trim. Slide glass to right side of fireplace to remove.
DF3015 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE POWER CORD 1. 2. 3. 4. Slide fireplace out of mantel 2-3 inches. Remove 4 Phillips screws from the right side of trim. Slide glass to right side of fireplace to remove.
