PARTS & SERVICE MANUAL FOR THE 30” FIREPLACE MODEL NUMBER: EF3003 SF3003 DF3003
TABLE OF CONTENTS OPERATION PAGE 1 PARTS DRAWING PAGE 5 PARTS LIST PAGE 6 WIRING DIAGRAM PAGE 9 LIGHT BULB REPLACEMENT PAGE 10 LED/SWITCH HARNESS REPLACEMENT PAGE 12 LIGHT DIMMER SWITCH REPLACEMENT PAGE 13 FLAME SPEED CONTROL REPLACEMENT PAGE 14 FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 15 HEATER ON/OFF SWITCH REPLACEMENT PAGE 17 HEATER ASSEMBLY REPLACEMENT PAGE 18 CIRCUIT BOARD REPLACEMENT PAGE 19 POWER CORD REPLACEMENT PAGE 20
EF3003, SF3003, DF3003 OPERATION Initializing The Remote Control 1. Turn on the electrical power at the circuit breaker. 2. Slide open the battery cover on the back of the remote transmitter. 3. Install three AAA batteries into the remote control. Replace the battery cover. Note: The LCD display will flash when new batteries are inserted. 4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press any button on the remote control.
EF3003, SF3003, DF3003 Timer Mode 1. You can set the timer to the length of time you want the unit to operate 2. (1 to 120 minutes). 3. Press the TIMER button once. The timer display will blink --4. Press the UP and DOWN buttons to adjust the timer display in minutes. 5. Press the TIMER button once to set the timer. 6. The timer setting can be reset by pressing the TIMER button and using the DOWN button until the timer display reads ----, press the TIMER button once to set the timer. 7.
EF3003, SF3003, DF3003 3
EF3003, SF3003, DF3003 Electric Fireplace Manual Controls A. Manual on/off switch 1. The fireplace has a manual power ON/OFF switch located on the control panel of the fireplace. 2. To operate press the switch once, to turn the unit on. A red light will illuminate to indicate the power is on. Press the switch again to turn the unit off. NOTE: When the manual power switch is used the heater will run. The manual ON/OFF switch is to be used only when the remote transmitter is OFF. B.
EF3003, SF3003, DF3003 17 16 20 20 8 12 6 7 18 15 3 22 2 5 1 14 17 13 4 9 10 11 19 21 5
EF3003, SF3003, DF3003 REPLACEMENT PARTS FIREPLACE 30” CATALOGUE NO. PART NO. MOD LEVEL: MADE IN: EF3003, SF3003, DF3003 6901110259, 6901110359, 6901110459 A CHINA REPLACEMENT PART REPLACEMENT PART NO. 1. LOG SET 0438550100RP 2. GRILLE 1009070159RP 3. HEATER ASSEMBLY 2200490201RP 4. LOWER LIGHT HARNESS 2500190500RP 5. UPPER LAMPHOLDER ASSEMBLY 4200120900RP 6. HEATER ON/OFF SWITCH 2800070200RP 7. CIRCUIT BOARD 3000210100RP 8. LED/SWITCH HARNESS 3000210400RP 9. REMOTE CONTROL 3000211600RP-ELECTRAFLAME 10.
EF3003, SF3003, DF3003 REPLACEMENT PARTS FIREPLACE 30” CATALOGUE NO. PART NO. MOD LEVEL: MADE IN: EF3003, SF3003, DF3003 6901110259, 6901110359, 6901110459 NONE CHINA REPLACEMENT PART REPLACEMENT PART NO. 1. LOG SET 0438550100RP 2. GRILLE 1009070159RP 3. HEATER ASSEMBLY 2200490200RP 4. LOWER LIGHT HARNESS N/A 5. UPPER LAMPHOLDER ASSEMBLY 4200120900RP 6. HEATER ON/OFF SWITCH 2800070200RP 7. CIRCUIT BOARD 3000210100RP 8. LED/SWITCH HARNESS 3000210400RP 9. REMOTE CONTROL 3000211600RP-ELECTRAFLAME 10.
EF3003 REPLACEMENT PARTS FIREPLACE 30” CATALOGUE NO. PART NO. MOD LEVEL: MADE IN: EF3003 6901110159 NONE CANADA REPLACEMENT PART REPLACEMENT PART NO. 1. LOG SET 0438550100RP 2. GRILLE 1009070159RP 3. HEATER ASSEMBLY 2000170300RP 4. LOWER LIGHT HARNESS 2500190100RP 5. UPPER LAMPHOLDER ASSEMBLY 2500080100RP 6. HEATER ON/OFF SWITCH 2800070200RP 7. CIRCUIT BOARD 3000210100RP 8. LED/SWITCH HARNESS 3000210400RP 9. REMOTE CONTROL 3000211600RP-ELECTRAFLAME 10. REMOTE CONTROL 3000211500RP-SYMPHONY 11.
EF3003, SF3003, DF3003 WIRING DIAGRAM 9
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE LED/SWITCH HARNESS 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2. Remove the firebox from mantel.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE LIGHT DIMMER SWITCH 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME SPEED CONTROL 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/FLAME ROD 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/FLAME ROD 14. Pick up wire connector and place (1) yellow wire into each terminal. (total of 2 yellow wires) 15. Secure wire connector by crimping the 3M symbol with slip joint pliers. 16.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ON/OFF SWITCH 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ASSEMBLY 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2. Remove the firebox from the mantel.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2.
EF3003, SF3003, DF3003 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE POWER CORD 1. Remove the trim by turning the retaining fasteners counter clockwise ¼ turn until the trim releases from the firebox using a slotted screwdriver. 2. Remove the firebox from the mantel.
