Owner’s Manual Model DF2608 NBDF2608 DF2622SS DF2622BLK IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. To view the full line of Dimplex products, please visit www.dimplex.
Table of Contents Welcome & Congratulations. . . . . . . . . . . . . . . . . 3 Important Instructions . . . . . . . . . . . . . . . 4 Fireplace Installation . . . . . . . . . . . . . . . . . . . . . . . 7 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . .
Welcome & Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex, the world leader in electric fireplaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.
Important Instructions ① Read all instructions before using the electric fireplace. ② This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation. ③ Extreme caution is necessary ⑨ Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the electric fireplace has been dropped or damaged in any manner. Contact Dimplex Technical Service 1-888-3467539.
Important Instructions ⑯ Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage to the heater. ⑰ Although this unit is of zero ⑳Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you must use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less then 1875 Watts.
Important Instructions ! NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Fireplace Installation WARNING: Ensure the power Fireplace Assembly cord is not installed so that The only assembly required is it is pinched or against any to slide the Front Glass onto the sharp edges and ensure that fireplace and install hardware to the power cord is stored or keep it in place. secured to avoid tripping or 1. Remove fireplace and glass snagging to reduce the risk of carefully from the carton, fire, electric shock or injury to discard the plastic bag and persons. foam packaging.
Fireplace Installation the fireplace (Figure 2). 5. Place the Front Glass onto the track of the fireplace (Figure 2) and slide it along the front until it reaches the far left of the unit. 6. Re-attach the right hand trim piece using the three (3) Philips screws from step 4. the fireplace near an existing outlet (refer to NOTE 1). 3. Store the fireplace in a safe dry and dust free location. CAUTION: Clearance for air circulation beneath the fireplace is provided by two (2) spacers.
Fireplace Installation Dimensions without trim are 26 ¼ inch (663 mm) wide x 22 ⅞ inch (580 mm) high x 8 ¾ inch (222 mm) deep. The fireplace does not require any additional venting (Figure 3). Fireplace Insert Installation Install the fireplace assembly into the mantel (refer to mantel assembly instructions). New Wall Construction 1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic. 2.
Fireplace Installation Option #2: A new outlet can be installed inside the framing construction. Plug the unit into a 15 Amp, 120 Volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 Watts. Existing Fireplace 1. Seal all drafts and vents with a non-fibrous insulation material to prevent any chimney debris from falling onto the fireplace. Do not install into an existing fireplace that is prone to dampness. 2.
Operation Figure 5 A B C Electric Fireplace Manual Controls (Figure 5) The manual controls for the fireplace are behind the access panel located at the bottom of the fireplace. A. Three Position On/Off Switch The switch has two (2) on positions marked with “ I ” and “ II ”. The “ I ” position is for manual operation. In this position the built-in remote control is bypassed. The “ II ” position is for operating the unit with the provided remote control.
Operation To turn the heater off, rotate the knob fully counter clockwise. Resetting the Temperature Cutoff Switch This unit is equipped with a thermostat which controls the temperature of the room by turning the heater on and off. The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset.
Operation ON button located on the remote control transmitter. ! NOTE: You will have only 10 seconds to perform this last step. Failure to do so will result in these steps needing to be followed again. This will synchronize the remote control transmitter and receiver. Figure 6 OFF Button ON Button Battery Cover Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons.
Maintenance Figure 7 Figure 8 Trim Log Set Assembly Front Glass the number of times you need to open the unit to replace light bulbs. Care must be taken when removing the Log set assembly as it contains LED’s and wires (DF2608 only). 1. Slide fireplace out of mantel. 2. Lay unit on it’s back for safe removal of front glass. 3. Remove three (3) Phillips screws from the right side of trim. 4. Remove trim. 5. Slide glass to right side of fireplace to remove (Figure 7). 6.
Maintenance clockwise. 12. Replace light filter bracket and flicker rod. 13. Install the log set assembly by placing the front, bottom edge of the ember bed in the track behind the control panel. Once in place, push down on the back edge of the ember bed until the rear tab snaps into place under the mirror (Figure 8). ! NOTE: Ensure the log set Assembly is installed tightly under the bottom edge of the mirror to prevent light leakage. 14.
Maintenance 6. 7. 8. 9. 10. 11. 16 of the fireplace to remove (Figure 7). Upper bulbs are located in the upper left and upper right corners of fireplace, behind the light block bracket (Figure 9). Remove the four (4) Phillips screws that attach the light block to the firebox (Figure 9). Unscrew bulbs counter clockwise. Insert new bulbs and screw in clockwise. Re-attach light block bracket. Lay unit on it’s back, slide front glass back into position and attach Trim.
Warranty Two Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to your newly purchased Dimplex electric fireplace. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser of the product only and is not transferable.
Warranty operation with an incorrect power source. refund the purchase price for such product or part. This limited warranty entitles the purchaser to on-site or inhome warranty services.
Warranty costs. Such costs shall not be the responsibility of Dimplex. • • For surrounds (mantels) and trims for the period ending at midnight on the first anniversary of the date of first purchase, Dimplex will in its sole discretion either repair or replace such defective surrounds (mantels) and trims or part thereof without charge.
Replacement Parts Log Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0439560100RP Flicker Motor.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000240200KIT Heater Assembly (Built-in Cutout). . . . . . . . . . . . . . . . . . . . . . 2000330100RP Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2300150100RP Main On/Off Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
