INSTRUCTION MANUAL 40cm HV Pedestal Fan Model: DCPF40C & DCPF40MB For domestic household use only.
IMPORTANT THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE. Note also the information presented on the appliance CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/ OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY Please read the operating instructions carefully before using your fan for the first time and keep them in a safe place. WARNING – This appliance must not be used in a bathroom.
• • • • • • • • Children should be supervised to ensure they do not play with the appliance. WARNING: To avoid danger of suffocation please remove all packaging materials particularly plastic and EPS and keep these away from vulnerable people, children and babies. NEVER drop or insert any object or fingers into any openings. Do not use the appliance in locations where paint, petrol or other flammable liquids are used or stored.
Exposed to the weather outdoors 4 Near water If the power cable wires are frayed or cut Where small children may be left unattended If an extension lead may become overloaded Where the power cable may be damaged On a slope or uneven surface Where there is risk of fire or close to a naked flame Where it may be damaged by chemicals Where there is a risk of interference by foreign objects This product is not made for DIY repair If there is a risk of water falling on the unit
Specification Model no. Colour DCPF40C DCPF40MB Chrome Matte Black Power supply 220-240V~, 50Hz Rated power 60W Speed settings 3 Modes - Timer - Air volume Adjustable height 141m3/min Yes - Max height 1.25m Tilt adjustable head Y Horizontal oscillation Y Noise level Weight (net) Dimensions (w x d x h) 77dB(A) 5.6kg 450 x 410 x 1250mm • For greater precision, please always refer to the rating label placed on the product.
Parts 2. Blade locking cap 6. Motor shaft 7. Rotary switch 4. Guard knob 8. Oscillation knob 1. Front grille 9. Motor housing 17. Safety screw 10. Power cord 11. Fixing screw A 12. Upper pillar 3. Fan blade 5. Rear grille 13. Fixing screw B 14. Main pillar 15. Base 17.
Assembly 1. Remove the pole fixing nut (16) from the main pillar (14) and insert the main pillar (14) into the base (15) then tighten the fixing nut (16). 2. Release fixing screw B (13) and adjust height to a suitable length. Re-tighten the fixing screw B once ready. 3. Release the fixing screw A (11), connect the motor housing with the upper pillar (12), fasten it with the fixing screw A (11). 4.
Cleaning Over time, dust can accumulate on the front & rear grille cover and fan blades, which can affect the fans performance. It is recommended to clean the fan at least once a month. 1. Turn the unit OFF and disconnect the appliance from the power supply. 2. Remove any dust build up with a soft brush. 3. Wipe the surface of the unit with a soft damp cloth. Mild detergent can be used for any stubborn marks.
Maintenance If the unit fails to operate efficiently, is broken or other problems arise, unplug and do not operate. Ask for advice by calling your local after sales service agent or the Customer Care Centre on 1300 556 816 (AU) / 0800 666 2824 (NZ). Warranty Please refer to the warranty card in the box for warranty information. For any troubleshooting advice, please contact the relative Customer Care Centre below.
Customer Care: 1300 556 816 customer.care@glendimplex.com.au www.dimplex.com.au Supplied by Glen Dimplex Australia 1340 Ferntree Gully Road, Scoresby, Victoria, 3179 © Glen Dimplex Australia. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex Australia.
