SERVICE MANUAL FOR COMPACT STOVE Model CS1205 7400290000R03
CS1205 Table of Contents OPERATION ............................................................................................................................. 2 REPLACEMENT PARTS ........................................................................................................... 4 WIRING DIAGRAM ................................................................................................................... 5 TO REPLACE LIGHT BULBS.................................................................
CS1205 OPERATION Compact Stove Controls A. Main on/off switch 1. The fireplace has a manual power ON/OFF switch located on the lower right side of the stove. 2. To operate, press the switch to turn the unit on or off B. Low Heat Switch Press this switch to turn the stove to low heat. C. High Heat Switch Press this switch to turn the stove to high heat.
CS1205 8 9 1 7 2 11 3 12 10 4 3 5 6
CS1205 REPLACEMENT PARTS COMPACT STOVE, DIMPLEX PART NO. REPLACEMENT PART 1. 2. 3. 4. 5. 6. 6902340100 REPLACEMENT PART NO. Log Set Assembly Flame Motor 120V Heater Assembly (comes with cutout) Main On/Off Switch Heater Switch Cord Set 120V (When 4100090103RP is gone use 7. Moulded Lampholder 8. Flame Rod 9. Mirror 10. Foot 11. Terminal Block 12.
CS1205 WIRING DIAGRAM 5
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE LAMPHOLDERS 1. Remove the light access panel from the bottom of the rear panel of the stove. 2. Remove the light bulb from the socket by turning counter clockwise. 3. Turn the stove over onto its top.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE ON/OFF AND HEATER SWITCHES 1. Turn the stove over and place it top down. 2. Remove the bottom heater assembly cover being careful not to damage any of the wiring. 3.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ASSEMBLY 1. Turn the stove over and place it top down. 2. Remove the bottom heater assembly cover being careful not to damage any of the wiring. 3.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE TERMINAL BLOCK 1. Lay the stove on its back with the front window facing upward. 2. Remove the bottom heater assembly cover being careful not to damage any of the wiring and lay it on the floor. 3.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/FLAME ROD 1. 2. 3. 4. Remove the 8 fastening screws on the top panel and remove the top of the stove. Lift glass out and store in a safe place.
CS1205 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE POWER CORD 1. Turn the stove over and place it top down. 2. Remove the bottom heater assembly cover being careful not to damage any of the wiring. 3.
CS1205 TROUBLESHOOTING GUIDE GENERAL Problem Cause Solution Circuit breaker trips or fuse blows when unit is turned on Improper circuit current rating Additional appliances may exceed the current rating of the circuit breaker or fuse.
CS1205 TROUBLESHOOTING GUIDE HEATER Problem Heater is not turning off Heater is not turning on Cause Solution Service Manual Reference Defective heater on/off switch Replace heater on/off switch Page 8 Improper operation Refer to Operation Section Page 2 Loose wiring Trace wiring in unit Page 5 Defective heater on/off switch Replace heater on/off switch Page 8 Defective heater assembly Replace heater assembly Page 9 Improper operation Refer to Operation Section Page 2 Loose wiring T
CS1205 TROUBLESHOOTING GUIDE NOISE Problem Service Manual Reference Cause Solution Dirty blower assembly Clean blower assembly Defective blower assembly Replace heater assembly Page 9 Moving flame rod hitting or rubbing against internal components Flame rod replacement Page 11 Defective flame motor Replace flame motor Page 11 Excessive noise with the heater on Grinding or excessive noise with the heater off 15
