Instructions / Assembly

ManualsBrandsDimensions ManualsLumber & CompositesPallet Board Holiday Snowflake Kit

THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR

USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE

CONSTRUCTION OR USE OF THIS PRODUCT. THE CONSUMER OR CONTRACTOR SHOULD TAKE ALL NECESSARY STEPS TO ENSURE THE SAFETY OF EVERYONE INVOLVED IN THE PROJECT,

INCLUDING, BUT NOT LIMITED TO, WEARING THE APPROPRIATE SAFETY EQUIPMENT. UNIVERSAL FOREST PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING

CONSEQUENTIAL DAMAGES.

RECLAIMED PALLET BOARD SNOWFLAKE KIT

ASSEMBLY INSTRUCTIONS

2801 E. Beltline NE, Grand Rapids, MI 49525 800.598.9663 (WOOD) 7/19

DimensionsDIY.com

Step 2: Assemble snowﬂake

Items needed for assembly

• 3 – Crosspieces

(#1 in Fig. 1)

• 6 – 2-piece wingtip

assemblies (#2 in Fig. 1)

• 1 – Pre-cut dowel (Fig. 3)

• 1 – Wood glue

packet (included)

• Place each of the (3) crosspiece/wingtip assemblies so that they're

all lying the same way, either facing up or down.

• Apply a small amount of wood glue to the pre-cut dowel (Fig. 3).

Coat dowel evenly using either your ﬁnger or a small brush.

NOTE: Do not over-apply glue. This may cause excess glue to

seep onto the faces of the crosspieces and cause any optional

ﬁnishes to coat unevenly, detracting from the overall appearance

of your completed project.

• One by one, slide the pre-drilled dowel holes over the glue-covered

dowel (Fig. 4). If needed, use a small rubber mallet to tamp them

down into place.

• Moving quickly, place the crosspieces at the desired angles,

adjusting as needed until even spacing and alignment is

achieved.

• Clamp if desired and allow glue to dry completely before adding

any custom ﬁnish(es).

Note: Finish your Giant Reclaimed Pallet Board Snowﬂake with

paint, stain, glitter, stencils, etc., or leave unﬁnished and enjoy its

natural, rustic ﬁnish. Match any décor, indoors or out, any way

you like. For outdoor use, protect your project with a water-

proof/weather-proof sealant.

• As noted above under Items needed, ﬁnish (or not) as you wish.

• Purchase the mounting hardware of your choice, including, if

necessary, the appropriate wall anchors for the wall material on

which you wish to display your snowﬂake. Hang and enjoy.

• Drop cloth or covered

work surface

• Rag for glue clean-up

• OPTIONAL – Rubber

mallet

• OPTIONAL – Clamps

Step 1: Assemble wingtip/crosspieces

Step 3: Finish & mount

• For your protection, wear safety glasses and gloves when

working with wood.

• Divide the (12) wingtip pieces (#2 in Fig. 1) into (6) pairs.

Place (1) pair at each end of each crosspiece.

Abutt the angled ends of each pair as indicated by the

red arrows in Fig. 2.

Use the red circle in Fig. 2 to help positioning the wingtips

at the end of each crosspiece.

NOTE: Placing the wingtips exactly as shown in Fig. 2

will result in slightly larger gaps between each crosspiece/

wingtip assembly, as shown in Fig. 5.

If less gapping (or no gapping) is desired, simply place

the wingtips an inch lower on the crosspiece (toward

the center), as shown in Fig. 6.

• Once comfortable with the position of the wingtips, evenly apply

provided wood glue to both wingtip pieces, reposition at each

end of each crosspieces, and apply even pressure until glue

is completely dry. Use clamps if desired.

Summary of content (2 pages)

PAGE 1
RECLAIMED PALLET BOARD SNOWFLAKE KIT ASSEMBLY INSTRUCTIONS Items needed for assembly • 3 – Crosspieces (#1 in Fig. 1) • Drop cloth or covered work surface • 6 – 2-piece wingtip assemblies (#2 in Fig. 1) • Rag for glue clean-up • 1 – Pre-cut dowel (Fig. 3) • 1 – Wood glue packet (included) • OPTIONAL – Rubber mallet • OPTIONAL – Clamps Note: Finish your Giant Reclaimed Pallet Board Snowflake with paint, stain, glitter, stencils, etc., or leave unfinished and enjoy its natural, rustic finish.
PAGE 2
RECLAIMED PALLET BOARD SNOWFLAKE KIT ASSEMBLY INSTRUCTIONS → O ← Fig. 2 Fig. 1 Fig. 4 Fig. 3 With gaps Fig. 5 Without gaps Fig. 6 THE DIAGRAMS AND INSTRUCTIONS IN THIS BROCHURE ARE FOR ILLUSTRATION PURPOSES ONLY AND ARE NOT MEANT TO REPLACE A LICENSED PROFESSIONAL. ANY CONSTRUCTION OR USE OF THE PRODUCT MUST BE IN ACCORDANCE WITH ALL LOCAL ZONING AND/OR BUILDING CODES. THE CONSUMER ASSUMES ALL RISKS AND LIABILITY ASSOCIATED WITH THE CONSTRUCTION OR USE OF THIS PRODUCT.