SQUARE DEAL ‘B’ Instruction Manual Version 4.5 illon recision Products, Inc.
Square Deal B Parts List Stock # 11628 11734 *12124 12864 13028 13328 13355 *13427 13429 13433 13437 13444 13445 13461 13479 *13504 13594 13597 13621 13622 13624 13644 13651 13657 13659 13673 13689 13690 13691 13705 13707 13712 13714 13718 13721 13722 13726 13739 13754 13756 13757 13764 13776 13789 13790 13793 13797 13798 13799 13801 13809 13815 13818 13822 13823 13828 13843 13845 13847 13850 13853 13857 Description Bullet Seater Insert Crimp Insert Seating Stem Carbide Sizer Insert Square Deal B Manual Sh
Square Deal B Schematic 17085, large 17086, small *13879 IMPORTANT The shellplate bolt (#13328) and linkarm bearings (#18077) require occasional lubrication. 22200 14040 12124 *20059 13908 13764 14037 (2) 13815 13815 13712 16523 (4) 13721 See page 4 for more detail. *13999 13822 *14003 See page 5 for more detail. 13896 13828 13461 13976 18077 13989 13328 13504 14037 Pre 1998 #13800 (old) 7/98 - Current #18077 13445 13433 13756 13860 See 13690 page 4 14019 for more detail.
Automatic Primer System SDB Automatic Primer System 20253 Large – 20012 Small 13957 13621 13657 13673 13689 13722 13726 13754 13757 13790 13798 13809 13823 13957 13961a 13961b 13964 13967 13979 13982 13989 14037 14051 20900 13673 Primer Cup – Large Primer Cup – Small Primer Magazine – Large Primer Slide Roller Primer Slide Bearing Return Spring Roll Pin Primer Slide Primer Punch – Small Primer Slide Return Pin Return Spring Roller Bolt Primer Punch Set Screw Primer Shield Cap Primer Feed Adjustment Scre
Automatic Powder System 20001 SDB Automatic Powder System 13644 13691 *13782 13793 13799 13801 13818 13845 13848 13853 13865 13871 13882 13893 13895 13904 13921 13943 13951 13958 13986 14023 14033 14036 14041 14202 14808 16340 16814 20063 20062 20642 20780 21353 22273 Powder Measure Spacer Powder Measure Tube Powder Funnel – Pistol Powder Measure Roller Stripper Wing Nut Tinnerman Insert Powder Bar Insert – Small Collar Sleeve Bellcrank Bushing Powder Bar Insert – Large Powder Die Bellcrank Cube 13691 Powd
black powder cartridges requires specialized loading equipment and techniques. Failure to do so can result in severe injury or death. • PRIMERS: Never force primers. If they get stuck in the operation of the machine, disassemble it and gently remove the obstruction. Never attempt to clear primers that are stuck in either the primer pickup tube or the primer magazine tube. Never, under any circumstances, insert any type of rod to attempt to force stuck primers out of these tubes.
13355 13594 Fig. 4 Fig. 4 – Install the return bracket (#13355) between the bottom of the shaft (#13437) and the spent primer chute (#13594). The spent primer cup (#13651) simply hooks on the bottom of the chute. Fig. 2 Fig. 2 – Using the machine itself as a template, mark the three mounting holes. Allow about one foot on both sides of your Square Deal “B” for working room. Make sure your bench is sturdy and does not shake, as this may disturb your powder charge and primer system. Fig. 5 Fig. 3 Fig.
Fig. 9 Fig. 7 Fig. 7 – Remove the cap from the top of the powder die (#13865). The cap retains the expander/powder funnel during shipping. Fig. 9 – With the cap removed and the expander/powder funnel in position, you are now ready to install the powder measure. Place the powder measure on top of the powder die. Fig. 8 Fig. 10 Fig. 8 – Make sure the expander/powder funnel is free to move in the powder die and reinsert it as shown. Fig.
To install the failsafe rod (#16814) remove the blue stripper wingnut (#13799), rod spring (#14033) and washer (#18086). (Note the order of parts.) See Fig. 11 Fig. 11 Insert the bottom end of the rod between the bench and the Square Deal “B” through the hole in the return bracket (#13355). Then, using your thumb and index finger of your right hand, move the locklink (#17838) down to align the hole with the slot on the Powder Measure bellcrank (#17839).
Now that you’ve seen the Square Deal “B” function, read the following description of what is happening at each station. Fig. 14 Understanding the Machine Station 1: When a cartridge is fired, it expands. The carbide resizer returns it to factory dimensions. The primer decap pin knocks out the old primer and deposits it into the spent primer cup. No adjustments are ever necessary at this station.
primer pick-up tubes have different colored tips. They have been color coded to help you identify size more easily. The color code is as follows: Blue Red Yellow Green Small Primer Magazine Orifice Large Primer Magazine Orifice Small Primer Pick-up Tube Large Primer Pick-up Tube tube until the follower rod touches the primers. You are now ready to reload. When you are nearly out of primers (approximately three remaining) the follower rod will activate the buzzer.
Technical Support & Order Line 1-800-223-4570 FAX (480) 998-2786 Fig. 18 Square Deal “B” Conversion Instructions Changing calibers on your SDB is a simple procedure. First, you must decide whether you need to change the priming system that is now set up on your machine. Small calibers use small pistol primers and large calibers use large pistol primers. Skip step one if there are no changes needed. Step 1: Changing The Priming System 4.
The short end of the ejector wire fits behind the shellplate bolt (#13328). Note: The correct positioning of the ejector wire is important or serious damage to the sizing die could result. See Fig. 14. Step 3: Changing and Adjusting Dies Use of Dillon’s Bench Wrench is suggested when changing or adjusting dies. Remove screw (#13895) and remove the powder measure. Remove screws (#13815) and (#14037) and remove the toolhead assembly. Lift out the three die inserts (#12864, #11628, #11734) from the frame.
On the cover… The Square Deal B is pictured with optional accessories: SDB Strong Mount #22223 Low Powder Sensor #16306 Other accessories available for the Square Deal B include: Bullet Tray #22214 Machine Cover #13795 Maintenance Kit & Spare Parts Kit #97015 The Blue Press, Dillon’s monthly catalog, has a complete listing of accessories available for all machines. Dillon Precision Products, Inc. 8009 E. Dillon’s Way Scottsdale, AZ 85260 (480) 948-8009 FAX (480) 998-2786 www.dillonprecision.
