Accessory Manual, May 2007 5/22/07 8:27 AM Page 1 Instruction Manual, May 2007 Case Preparation Tools & Reloading Accessories illon recision Products, Inc.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 3 Case Preparation & Accessory Instruction Manual Table of Contents Page Case/Media Separators 1 Case Lube, Rapid Polish 290 & Media 2 Rapid Trim 1200B Case Trimmer 3&4 SS-600 Super Swager 5&6 Pistol & Rifle Case Gages 7&8 Kinetic Bullet Puller 9 Eliminator Beam Scale 10 Akro Bins & Utility Boxes 11 Pistol & Rifle Ammo Boxes 12 WARRANTY INFORMATION All electrical/electronic components in Dillon equipment are covered by a one year warrant
Accessory Manual, May 2007 5/22/07 8:27 AM Page 4 Dillon Large & Small Case/Media Separator Dillon’s small and large case/media separators. Large Separator, #20675 Small Separator, #21045 TO ASSEMBLE: Open the blue separator basket by pulling the spring loaded latch(es). Using the 1-1/4” bolts, fasten the crank handle across the bottom half of the basket (the half without the latches). Be certain the crank handle is in the down position. (See above photo.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 5 Dillon Case Lube, Dillon Case Lubricant and Rapid Polish 290. Case Lube - 8 oz #13733 Case Lube - case 20 bottles #20256 #13804 Rapid Polish 290 - 8 oz Rapid Polish 290 - case 20 bottles #20255 10 Bottles of Each #21375 Walnut Media - 15 lb. bag #13287 Corn Cob Media - 10 lb. bag #13496 1 Bag each Corn & Walnut Media #21553 Dillon Case Lube: Lay your cases out in a single layer and spray lightly with one or two passes.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 6 Dillon Rapid Trim 1200B Case Trimmer TO OPERATE: You will need a case gage to set the size/trim die properly. (See page 10) For best results you need to clean and lube your brass before sizing and trimming. Install the size/trim die (without the trim motor) into the toolhead on your reloading machine. Screw it down until it touches the shellplate and then back it out 1/2 turn. The size/trim die is adjustable.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 7 Dillon Rapid Trim 1200B Case Trimmer Connect the power cords and turn the Size/Trim Die Part # motor on. .222 Rem #21363 Trim a case and check it for overall length .223 Rem #20107 in a case gage. To check for overall length, set .220 Swift #21364 the case firmly into the case gage and set the .22-250 #20110 gage on a clean, flat surface. The case mouth .243 Win #20109 should be between the high and low step of .25-06 #21367 .
Accessory Manual, May 2007 5/22/07 8:27 AM Page 8 Dillon SS-600 Super Swager Most military brass has a crimped primer pocket and therefore requires swaging. The crimp must be removed prior to repriming and reloading the case. TO OPERATE: First make sure all of your brass has been deprimed. Use the proper diameter case locator rod. The unit comes with the .223 rod installed. The larger rods are for .30 cal, .38 and 9 mm. For .45 ACP, use the bushing (not pictured) over the .30 caliber rod.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 9 Dillon SS-600 Super Swage A properly swaged pocket should have a smooth radius (see photograph B). Set the locator rod for minimal swage and swage a case. Examine the edge of the primer pocket to be Photo “B”: The case on the left shows a sure it is smooth, then seat a properly swaged primer pocket. primer in it. Repeat this process until enough swage is achieved to seat a primer easily.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 10 Dillon Case Gages B A low step high step C D low step72high step & 73 Figs Fig 1 A B Fig 2 A B How to use the Case Gage: The way the case gage works is this: Once you’ve made a preliminary adjustment to your sizing die drop the sized case all the way into the case gage, Fig 1. Look at the base of the case. If the base of the case is below the high step (see “B” Fig 2) and above the low step (see “A” Fig 2) then the sizing die is properly adjusted.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 11 Dillon Case Gages, cont… NOTE: Before inserting any case into a case gage, make sure it is wiped clean of any lubricant. Otherwise, the lubricant will accumulate inside the case gage and cause it to become coated with grit and dust. This will cause the case gage to give inaccurate readings. Always refer to a reliable loading manual for case dimensions. RIFLE case gages have “steps” on the top and base.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 12 Kinetic Bullet Puller Cap Chuck Nose Kinetic Bullet Puller, #17999 IMPORTANT For use on CENTERFIRE CARTRIDGES only. Not for use with rimfire cartridges or explosive-projectile ammunition. Before you begin make sure the FLAT side of the metal chuck assembly sits on the flat surface of the puller body and the cap is threaded on. Also note that the rubber strip is crimped to the chuck jaws, it is not a ring.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 13 Dillon Eliminator Scale Copper Damper Vane Poises End Loop Leveler Foot Eliminator Scale, #13480 TO OPERATE: Be sure that the gold-colored powder pan is set on top of the silver-colored pan support before zeroing the scale. The scale has three poises: 0 - 500 grains in 10 grain increments; 0 10 grains in 1 grain increments; 0 - 1 grain in .1 grain increments.
Accessory Manual, May 2007 5/22/07 8:27 AM Page 14 Dillon Akro Bins and Utility Boxes Akro Bins Square Deal Cartridge Bin #13756 10 Pack Blue Bins #20913 #20914 24 Pack Blue Bins 48 Pack Blue Bins #20952 RL550/XL650 Cartridge Bin#13839 #20917 10 Pack Blue Bins 24 Pack Blue Bins #20918 48 Pack Blue Bins #20953 RL1050 Cartridge Bin 6 Pack Blue Bins 12 Pack Blue Bins 24 Pack Blue Bins SL900 Cartridge Bin 6 Pack Blue Bins 12 Pack Blue Bins 24 Pack Blue Bins #13484 #20915 #20916 #20954 #17125 #97042 #9704
Accessory Manual, May 2007 5/22/07 8:27 AM Page 15 Dillon Ammunition Boxes Pistol Ammunition Boxes 9mm (50 rd) 9mm (100 rd) .38/357 (50 rd) .38/357 (100 rd) .44 (50 rd) .44 (100 rd) .45 ACP (50 rd) .45 ACP (100 rd) One Box #13784 #13645 #13476 #13766 #13568 #13680 #13715 #13574 Note: “.38” series boxes fit .38 Super, .38 Special & .357. “9” series boxes fit .30 Luger, 9x21 and .380. “44” series boxes fit .41 Mag, .44-40 and .45 LC. “.45” series boxes fit 10mm and .40 S&W.
Accessory Manual, May 2007 5/22/07 illon recision Products, Inc. Manufacturers of the World’s Finest Loading Equipment 8:27 AM Page 16 8009 E. Dillon’s Way Scottsdale, AZ 85260 (480) 948-8009 Fax: (480) 998-2786 For technical assistance or orders: (800) 223-4570 To place an order by stock numbers or to quickly check the status of an order only.
