9" TFT LCD CONSOLE WITH KVM SWITCH (8-PORT/16-PORT) User Manual DS-72303GE / DS-72303US DS-72402GE / DS-72402US
LCD MONITOR SPECIFICATIONS Size Screen Type Contrast Brightness View Angle Resolution Response Time Display Color 19 inch TFT 700:1 300 cd/m2 160° 1280x1024@75Hz 6 ms 16.2 M OPERATION Keypad Define Power key: Use this key to turn on or off the LCD monitor. Menu key: Use this key to open the OSD menu and enter to next menu or to highlight a confirmed function.
OSD Control Function List 1. Color: Contrast Brightness Color Adjust Color Temp.: 9300, 6500, 5800, 5RGB, USER Exit 2. Image Setting: Clock Phase Gamma Sharpness Exit 3. Position: H.Position V.Position Exit 4. OSD Menu: OSD H.Pos OSD V.Pos OSD Timer Exit 5. Language: English, Français, Deutsch, Español, 繁體中文, 简体中文, 日本語 6. Misc.: Signal Source Reset Factory Mode Exit 7.
BRIEF INTRODUCTION The KVM Switch allows you to control several sets of personal computers by a keyboard, a mouse and a monitor. In the meantime, you just need to connect the cable and turn on the power to control up to 256 sets of personal computers without installing any additional interface card or software. Easy Installation The 3-in-1 CPU Connector (VGA, Keyboard and Mouse) can save the installation time and space and assure the correct signals.
FEATURES ‧ ‧ ‧ ‧ ‧ ‧ ‧ ‧ ‧ ‧ The keyboard, mouse and 19” LCD monitor were built-in on the KVM switch. Standalone machine controls up to 4/8/16 sets of PCs. Cascade controls 64/128/256 sets of PCs. Through OSD, you can use the hot key, mouse clicking and push button on front panel to switch PCs. Monitors PC status by Auto Scan function. Supports resolution of 1280x1024, 75Hz and independently supports EDID & DDC2 of each PC.
SPECIFICATIONS CPU Connecter 3-in-1 HD-15 (Female) Monitor Console Mouse Connector Keyboard Port Selection Keys on Front Panel Port LEDs Power OSD Video Resolution Dimensions Weight Operating Temp Storage Temp Humidity 8-port 16-port 8 16 19” TFT LCD Touch pad module Standard 104 keys 8 16 8 1 16 1 Built-in 1280x1024@75Hz 600x450x48 mm 13.35 Kg 13.
CONFIGURATION 8-Port Front View 16-Port Front View 1. Port Selection Switches Press the push button to directly switch to the corresponding PC. • In the cascade architecture, if the port is connected to KVM but not PC, then the push button will not respond. • Simultaneously press Push Buttons 1 and 2 to directly enter the OSD Control Mode. 2. Port LEDs These Port LEDs are built in the Port Selection Switches.
-Port Rear View 16-Port Rear View 1. CPU Port Install the cable connected to a PC here. 2. Update Port The port provides a firmware update function. 3. AC Power Jack The AC Power is applicable for 100~240VAC, 50Hz~60Hz 4. Power Switch Power On/Off the LCD KVM.
INSTALLATION • Standalone 1. Make sure that the power switch at the rear panel of the KVM is OFF. Plug an end of the AC power cord into the KVM and the other end to an AC power supply. 2. Make sure to power off the PC and then install the 3-in-1 cable to each of the PC one by one.
7. Power on the PC. Note It is not necessary to power down the whole system for install a new PC or KVM thereafter. All you need is to make sure that the new PC or KVM is OFF during the installation. If the KVM powers down due to external factors (such as power failure or the power of the KVM is turned off), we recommend you to reinstall the whole system. Note: It is noteworthy that there are two levels available. • Expansion 1.
OPERATION Port Selection The LCD KVM provides fours switching methods: Manual Key, Hot Key, Mouse Clicking and OSD. • Manual Key It is the simplest switching method. You just need to press the Port Selection Switch on the front panel of the KVM. The Selection LED (Red) is on, indicating that you are switching to the corresponding port. Note: 1. The Port Selection Switch functions only when connected to a PC. 2.
• • Operation You can operate the options by keyboard or mouse. For the keyboard operation, besides the common Up and Down keys, there are special function keys such as Enter, Space Bar, Function Key (F1,F4…) under the OSD remark field. For the mouse operation, the left key refers to Enter and the right key refers to Exit. For example, move the mouse point to your desired PC, and click the left key. The selection bar will move to that position and then click the left key again for the execution.
1. This field provides the information of the currently connected PC. As shown in the figure above, 03 refers to the Port Number of the Master; 04 refers the Port Number of the Slave; and Mail Ser 4 is the name of this PC defined by Users. If a PC connects to the Master, then the number consists of the first two digits. If a User has not given a name for the PC, the name field will be blank. 2. This field shows the list of the Master KVM or a certain set of Slave KVM currently displayed on the OSD.
4. Instruction Hint Field: ↑↓: Move; Use the ↑↓ keys on the keyboard or the mouse to move the selection bar. SPACE: Edit; The “Space BAR” on the keyboard is used to start editing the name of the PC or KVM. ESC: Exit; Use the “Esc” key on the keyboard to exit the current option or exit OSD. F4: Auto Scan; Use the F4 key to run Auto Scan, and you can set the residing time, channel display time and mode of the Auto Scan from System Setting.
Item Description For Port Switching, Auto Scan and OSD Channel Display Close, the Monitor will show the Channel Mode information and mode selection. Channel Display It shows the time for displaying channel Time information. For Auto Scan, it shows the residing time Auto Scan Time for each port. Select to turn on the hot keys of the OSD OSD Entry Hot Key control screen. Turn on/off the “Ctrl” hot keys on the Hot Key Switching keyboard for switching computer functions.
• Auto Scan Mode: You can start the OSD first and press “F4” to enter the Auto Scan Mode. If you want to scan the PC, you must use the Smart View Setting to select the Auto Scan Time in the System Setting for the residing time, which includes 5 sec, 10 sec, 20 sec, 30 sec and 60 sec. You can adjust the Channel Display Mode and Channel Display Time from the Channel Display mode. By then, all keys on the panel, keyboard and mouse are not operable. You can only use the ESC key to exit the Auto Scan Mode.
TROUBLESHOOTING Confirm whether or not the cable is good and connected properly Q1 : What should we do if the keyboard has no response? A1a: Reboot the PC. A1b: For Auto Scan Mode, press [Esc] to exit. Q2 : A2a: A2b: What should we do if the mouse has no respond? Reboot the PC. For Auto Scan Mode, press [Esc] to exit. Q3 : A3a: What should we do if the OSD cannot display normally? If the KVM switch is a standalone, then power off the PC.
