54Mbps IEEE 802.
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits.
Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency (RF) signal. CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.
TABLE OF CONTENT Introduction..................................................................................................... 1 Overview of this User’s Guide...................................................................... 1 Unpacking and Setup....................................................................................... 3 Unpacking..................................................................................................... 3 Setup .................................................
INTRODUCTION Congratulations on your purchase of this 54Mbps IEEE 802.11g Wireless LAN Adapter. This manual helps to get familiar with the 54Mbps IEEE 802.11g Wireless LAN Adapter. This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. With a Wireless LAN Adapter, a laptop computer or a station can communicate with another computer in a wireless way.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the 54Mbps IEEE 802.11g Wireless LAN Adapter. Unpacking Open the box of the 54Mbps IEEE 802.11g Wireless LAN Adapter and carefully unpack it. The box should contain the following items: u One 54Mbps IEEE 802.11g Wireless LAN Adapter u One Driver & Utility with User’s Guide CD-ROM If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION LED Indicator for CardBus Link The Link LED indicator lighted green when the 54Mbps IEEE 802.11g Wireless LAN Adapter is connected to wireless network successfully. ACT (Activity) The ACT LED indicator blinking green when the 54Mbps IEEE 802.11g Wireless LAN Adapter is transmitting or receiving data. LED Indicator for PCI Link The Link LED indicator lighted green when the 54Mbps IEEE 802.11g Wireless LAN Adapter is connected to wireless network successfully.
SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the Wireless LAN Adapter. Windows 98/ME/2000/XP Utility and Driver Installation 1. Insert the 54Mbps IEEE 802.11g Wireless LAN Adapter Driver & Utility CDROM into computer’s CD-ROM Drive and it will automatically run a setup menu and install the driver and the utility. In some specific setting on Windows system, you may need to proceed the software manually, go to your Windows Start menu and choose Run, type “D:\Setup.
WIRELESS UTILITY SETTING Link Information The default page is as below after launching the Utility program. Status: Shows the BSSID associated, which can be used to identify the wireless network. SSID: Shows current SSID, which must be the same for the wireless client and AP in order for communication to be established. Frequency: Shows the current frequency used for wireless network. Wireless Mode: Shows the current wireless mode used for wireless communication.
Configuration This is the page where changes the basic settings of the wireless LAN adapter with the minimum amount of effort to implement a secure wireless network environment. SSID: Service Set Identifier, which is a unique name shared among all clients and nodes in a wireless network. The SSID must be identical for each clients and nodes in the wireless network.
Power Mode: There are 3 modes to choose. · Continuous Access Mode (default) – the wireless LAN adapter is constantly operating with full power and it consumes the most power. · Maximum Power Save – the wireless LAN adapter consumes the least power and only operates when there is wireless network activity. · Power Save – the wireless LAN adapter consumes the moderate level of power. Preamble: Select Long or Short Preamble type.
Advanced This is the page to configure Security settings of the 54Mbps IEEE 802.11g Wireless LAN Adapter. Auth Mode: Select the authentication type from drop down list for Disable, Open System, Shared Key, WPA, WPA-PSK, WPA2 and WPA2-PSK. Open System / Shared Key WEP Key 1~4: choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space.
Key Length: select 64 or 128 bits as the length of the keys. If you select 64bit in Hex format, you must type 10 values in the following range (0~F, hexadecimal), or 64bit in ASCII format, you must type 5 values in the following range (0~9, A~Z and a~z Alphanumeric); If you select 128bit in Hex format, you must type 26 values (0~F, hexadecimal), or 128bit in ASCII format, you must type 13 values in the following range (0~9, A~Z and a~z Alphanumeric). Default Key: select one of the 4 keys to use.
Site Survey This page allows user to enable the Site Survey function to scan for the available wireless network (wireless clients and Access Points) and establish wireless communications with one. Available Network –displays the wireless networks (wireless clients and Access Points) that are in signal range. Select any one of them to establish communications by simply mouse double-click or click on the “Connect” button. Click “Refresh”button to start scanning for available network again.
About This page displays some information about the 54Mbps IEEE 802.11g Wireless LAN Adapter utility, which includes the version numbers for Driver, Firmware and Utility. When there is new version of software available for upgrade, users will be able to identify by version numbers.
TECHNICAL SPECIFICATIONS General Radio Technology IEEE 802.11b Direct Sequence Spread Spectrum (DSSS) IEEE 802.11g Orthogonal Frequency Division Multiplexing (OFDM) Interface PC Card: 32-bit CardBus, PCI Adapter: 32-bit PCI bus Data Transfer Rate 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps Receiver Sensitivity 54Mbps: Typical -70dBm @ 10% PER (Packet Error Rate) 11Mbps: Typical -86dBm @ 8% PER (Packet Error Rate) Transmit Power 802.11b: 15±2dBm 802.
