Digitus DN-11009 2 USB 2.0 Hi-Speed-Port Multifunction Router User’s Manual Version 1.
Table of Contents CHAPTER 1 INTRODUCTION.....................................................................................................3 1.1 HARDWARE SPECIFICATION ..........................................................................................................3 1.2 FEATURES .....................................................................................................................................3 CHAPTER 2 PRODUCT OVERVIEW ........................................................
Chapter 1 Introduction 1.1 Hardware Specification Digitus DN-11009 is a multifunction router. Besides the basic functions of router, Digitus DN-11009 has two additional USB host ports to support FTP server, print server, and webcam server. The following list shows the hardware specification for Digitus DN-11009. z z z z z z WAN Port x 1 LAN Port x 4 USB 2.0 Host Port x 2 LED x 9 Init Button (factory default and firmware upgrade) Power Adaptor Connector (DC 12V/1A) 1.
Chapter 2 Product Overview 2.1 Package Contents z Digitus DN-11009 z Power adaptor z CD 2.2 Hardware Description 2.2.1 Rear Panel The rear panel includes a Power Inlet, a Init Button, four LAN Ports and one WAN Port. Power Inlet: use DC IN 12V/1A adaptor. Init Button: reset the parameters to the factory default values. LAN Port: for twisted pair category 5 cable. The 4 LAN ports are for the connection to internal PCs. WAN Port: for twisted pair category 5 cable.
Off LAN2 On Off LAN3 On Off LAN4 On Off USB1 On Blinking Off USB2 On Blinking Off No physical connection to network (LAN1) Network Connected (LAN2) No physical connection to network (LAN2) Network Connected (LAN3) No physical connection to network (LAN3) Network Connected (LAN4) No physical connection to network (LAN4) USB device connected (USB1) Connected USB device not supported (USB1) No physical connection to USB device (USB1) USB device connected (USB2) Connected USB device not supported (USB
Chapter 3 Installation 3.1 Hardware Connections Make sure that your USB devices are powered off and that the Router’s Power Adapter is disconnected. Connect your PC to one of the Router’s LAN port with a twisted-pair category 5 cable, 10baseT or 100baseTX. Connect the Router’s WAN port to an ADSL modem with a twisted-pair category 5 cable, 10baseT or 100baseTX. Connect the Power Adapter to the Router. The power indicator will light up and USB1 and USB2 indicators will flash in turn.
At control panel, double click Network Connections. All your connections will be displayed on the window. Go to Local Area Connection and click mouse right button. A menu will appear, select Properties.
At Local Area Connection Properties window, select the General tab. Select Internet Protocol (TCP/IP) and then click Properties. If you use DHCP to get IP automatically, select Obtain an IP address automatically and then click OK to finish the setting.
the router can automatically get IP address. If you get IP manually, select Use the following IP address. The factory default router LAN IP address is 192.168.1.100. Therefore, we use an IP address located in 192.168.1.x block to get connect to the router. Here we use 192.168.1.11 as an example. Click OK to finish the setting. 3.3 Access Router Home Page from Web Browser This router can be configured through its web pages. Follow the steps below to access the router web pages.
If you login successfully, the router main web page will appear and you can start to configure the router from web pages. 3.4 Enable UPnP on Windows The UPnP (Universal Plug and Play) enables communication between any two devices under the command of any control device on the local network. PCs that have enabled UPnP function are informed when a device, this Router, for example, is connected to the local network.
Go to desktop and click Start Æ Control Panel. At Control Panel window, double click Add or Remove Programs.
Click Add/Remove Windows Components. Select Network Services and then click Details.
Tick Universal Plug and Play and then click OK. Back to this window, click Next. Windows will install the component automatically. z Depends on the version of your OS, the original Windows CD might be required after this step. If so, please insert your original Windows CD.
Click Finish. Once the UPnP is enabled, the computer will be informed by this icon when a new device is connected to the local network. You can click this icon to get the UPnP-supported device list.
Chapter 4 Settings 4.1 Quick Setup Quick Setup supports 4 WAN Connection Types - ADSL Dialup (PPPoE), ADSL Static IP, Automatic IP and Cable Modem (DHCP). If you do not know your WAN type, consult your ISP. Start quick setup by selecting your WAN Connection Type from the drop-down list. 4.1.1 ADSL Dialup (PPPoE) If your ISP provides you the ADSL Dialup, please follow the following steps to setup your WAN connection. [Page 1] Select ADSL Dialup from the drop-down list.
[Page 3] Click the services that you want to block and input the time period that you want the selected services to be blocked. If you don’t want to block any services, leave all options empty. 4.1.2 Static IP If your ISP provides you the static IP, please follow the following steps to setup your WAN connection. [Page 1] Select ADSL Static IP from the drop-down list.
[Page 2] Input the IP Address, Subnet Mask, Default Gateway, and DNS Server provided by your ISP. [Page 3] Click the services that you want to block and input the time period that you want the selected services to be blocked. If you don’t want to block any services, leave all options empty. 4.1.3 Automatic IP If your ISP provides you the automatic IP, please follow the following steps to setup your WAN connection.
[Page 1] Select Automatic IP from the drop-down list. [Page 2] Click the services that you want to block and input the time period that you want the selected services to be blocked. If you don’t want to block any services, leave all options empty. 4.1.4 Cable Modem (DHCP) If your ISP provides you the Cable Modem (DHCP), please follow the following steps to setup your WAN connection. [Page 1] Select Cable Modem (DHCP) from the drop-down list.
[Page 2] Click the services that you want to block and input the time period that you want the selected services to be blocked. If you don’t want to block any services, leave all options empty. 4.2 IP Configuration IP Configuration allows you to configure some basic functions including IP Setup, DHCP Server, Routing Table and Miscellaneous. 4.2.1 IP Setup You can use IP Setup section to configure your WAN connection and LAN IP.
WAN Connection Type: Select ADSL Dialup (PPPoE) from the drop-down list. WAN DNS Setting: Select Yes to get DNS Server automatically. PPPoE Account: Input the user name and password provided by your ISP. The MTU value can be changed if required. WAN MAC Address Setting: This has a default value given by the manufacturer and you are recommended not to change this value. LAN IP Setting: There is a default LAN IP given by the manufacturer. You can change this as required.
WAN Connection Type: Select ADSL Dialup (PPPoE) from the drop-down list. WAN IP Setting: Input the IP Address, Subnet Mask and Default Gateway provided to you by your ISP. WAN DNS Setting: Select No to set the DNS manually and input the DNS Server IP. If you don’t know, please check with your ISP. The MTU value can be changed if required. WAN MAC Address Setting: This has a default value given by the manufacturer and you are recommended not to change this value.
WAN Connection Type: Select Automatic IP from the drop-down list. WAN DNS Setting: Select Yes to get DNS Server automatically. WAN MAC Address Setting: This has a default value given by the manufacturer and you are recommended not to change this value. LAN IP Setting: There is a default LAN IP given by the manufacturer. You can change this as required. Please note that you should use the new IP address to login to this router. Apply/Cancel: Click Apply to save the settings or click Cancel to aboard.
WAN Connection Type: Select Automatic IP from the drop-down list. WAN DNS Setting: Select Yes to get DNS Server automatically. WAN MAC Address Setting: This has a default value given by the manufacturer and you are recommended not to change this value. LAN IP Setting: There is a default LAN IP given by the manufacturer. You can change this as required. Please note that you should use the new IP address to login to this router. Apply/Cancel: Click Apply to save the settings or click Cancel to aboard. 4.2.
DHCP Server supports up to 253 IP addresses for you local network. Follow the instructions to configure DHCP Server. Enable DHCP Server: Select Yes to enable or No to disable DHCP Server. Domain Name: Domain Name is the name which you had registered from NIC (Network Information Center). Ignore this part if managers don’t apply for a domain name. IP Pool Starting/Ending Address: You can use this to set the IP range that the DHCP server can offer.
Routing Table page allows you to set routing rules to this router. This includes static routing and dynamic routing. Static Route: Input the IP address of a destination network or a host of the routing rule. It could be a host address like 192.168.123.100 or a network address, such as 192.168.0.0. Click Add to add the rule to the routing table or select a rule from the table and then click Del to delete the rule. Dynamic Route: If you don’t want to set any dynamic routing rule, select Disable.
Miscellaneous includes web server port setting, access control from WAN and DDNS setting. You can enable or disable some services when clients access from WAN. Enable the DDNS Client: Select Yes to enable or No to disable the DDNS client. DDNS Server: Select a DDNS server from the drop-down list or click Free Trial to link up a free trial address. User Name or E-mail Address: User name or e-mail address is used as an identity to login to some DDNS services.
NAT Setup contains three functional items including Port Trigger, Virtual Server and Virtual DMZ. 4.3.1 Port Trigger Application-triggered port forwarding opens a port only when a program needs to use it. You can set a trigger port to open an incoming port. When trigger ports are used, the system opens the specified incoming ports. To setup port trigger, follow the instructions below. Enable Port Trigger: Select Yes to enable or No to disable port trigger.
and input the port number by yourself. Trigger Ports: Input the port number that will trigger the action. If this port was active by a program, the system will open the corresponding incoming port. Incoming Ports: Input the port number that will be open if the trigger port is active. Protocol: Select from the list whether this rule should be applied to TCP or UDP or both. Description: You can input some description of this rule.
Enable Virtual Server: Select Yes to enable or No to disable virtual server. Well-Know Applications: The drop-down list has listed some well-know applications, you can get the port number of an application by selecting from the drop-down list. Or you can also select User Defined from the list and input the local port number and server port number by yourself. Local IP: Input the local server IP. For example, the IP address of your web server on you network. Local Port: Input the port number.
the rule table. If you want to delete a rule from the table, select the rule and click Del. Then the high-lighted rule will be removed from the list. Apply/Cancel: Click Apply to save the settings or click Cancel to aboard. 4.3.3 Virtual DMZ You can redirect every connection from the Internet to a computer on your network by setting up a virtual DMZ. Every connection your WAN IP form the Internet will be redirected to the specified IP address on your network.
4.4.1 IP Filter IP Filter blocks connections according to their IP addresses and ports. You can also set start time and end time if you only want to apply the filter rules during a specific period in a day. Enable Firewall: Select Yes to enable or No to disable firewall. Enable Firewall Log: Select Yes to enable or No to disable firewall log. Source IP and Port Range: Input the source IP address and port range for the filtering rule.
apply to TCP or UDP or both. Start Time/End Time: Set a period of time to drop or accept the connection. Type: Select from the drop-down list for dropping or accepting the connection. Add/Del: After fill up all your requirement of a rule, click Add to add the rule to the rule table. If you want to delete a rule from the table, select the rule and click Del. Then the high-lighted rule will be removed from the list.
Enable MAC Filter: Select Yes to enable or No to disable MAC filter. MAC Address specified will be: Select DROP or ACCEPT from the list to mean all the connections to the MAC addresses on the list should be dropped or accepted. MAC Address: Input the MAC address that you want to apply to this rule. Start Time/End Time: Set a period of time to drop or accept the connection. Add/Del: After fill up all your requirement of a rule, click Add to add the rule to the rule table.
Enable URL Filter: Select Yes to enable or No to disable URL filter. URL Keyword: Input a full URL or a keyword of an URL. For example, input “www.abc.com.tw” will only block the URL perfectly matches this URL while input “abc” will block all the connections that contain “abc” in its URL. Start Time/End Time: Set a period of time to drop or accept the connection. Add/Del: After fill up all your requirement of a rule, click Add to add the rule to the rule table.
The FTP server function allows you to share files on the network. This product supports a file format of FAT12/16/32. Please follow the steps below to configure FTP server. Enable FTP Server: Select Yes to enable or No to disable FTP Server. Allow Anonymous User to Login: Select Yes to allow users use anonymous to login or select No to forbid users use anonymous to login.
Select Yes to enable or No to disable user log in to FTP as super user. Maximum Users Allowed to Login: Input the maximum amount that the system can allow users to login at the same time. FTP Port: The default FTP Port is 21, you can change it if necessary. Add/Del: To add a user account, input user name, password, max login and file access right of the new user and then click Add. To delete a user account, select the user from the account list and then click Del.
4.5.2 Print Server The Print server function allows you to share printers on the network. Digitus DN-11009 support LPR printing protocol. Please follow the steps below to configure print server.
Enable Print Server: Select Yes to enable or No to disable print Server. Printer1 Name: This is the printer name of the first printer. There will be a default printer name. You can change it if you want. Remember this name will be the one you should use when adding printer on Windows. Printer1 Model: The model of the first printer. Printer2 Name: This is the printer name of the second printer. There will be a default printer name. You can change it if you want.
Click Add a printer. Click Next.
Select Local printer attached to this computer then click next. Select Create a new port and set type of port to Standard TCP/IP Port. Click next.
A wizard of adding a new standard TCP/IP port will appear. Click Next. Give a name to this new port. Then click Next.
Select device type to Custom. Then click Settings. Set protocol to LPR and set queue name as the printer name you set on router web site. Here we use USSB1_LQ for example. Click OK.
Once the device type is configures, the wizard will back to this page. Click Next. Click finish to complete the add printer port wizard.
Select printer driver. Here we use HP LaserJet 1200 Series PCL for example. Click Next. Give this printer a name. This name is used for Windows display. There will be a default printer name, you can change if necessary.
Select whether you want to print a test page or not. Here we select Yes as an example. Click finish to complete the add printer wizard.
If the test page is printed, click Ok. Otherwise, click Troubleshoot. There will be a new printer added to your printer list. 4.6 System Setup 4.6.
router. Input the new user name and password that is to be used as the administrator of the router. Retype the password and click Apply to save the settings or Cancel to aboard. *Note that you should use the new user name and password to login to the router web site once applied. 4.6.2 Time Setup You can set the router clock to your local time and daylight saving time. You can get current time from NTP (Network Time Protocol) server or from your local computer.
Current Router Time: This field displays your current router time. Using NTP to Get Time: Select this if you want to get time from NTP server. NTP Server: Select a NTP server from the drop-down list. Time Zone: Choose your local time zone from the drop-down list. Daylight Saving Time: Select an option to enable or disable daylight saving time. User Setup: Select this if you prefer setup time manually. Input the time for each field or you can also get time from your local computer.
This page displays the current firmware information of your router. You can always keep your router updated to the latest version from this page as well. Please follow the steps below to upgrade router firmware. Product ID: This field displays product ID of your router. Firmware Version: This field displays the firmware version that your router is using currently. New Firmware File: Click Browse to get the new firmware that you would like to upload. Upload: Click Upload to upgrade the firmware. 4.6.
Click Here to save your current settings into a file for backing up. If you want to get your original settings back, click Browse to get your saved settings and click Upload to apply. The system will reboot automatically, all the settings will be restored to the original value after reboot. 4.6.5 Restore Default You may restore the router to factory default settings from this page. To restore default settings, simply click the Restore button. The system will reboot automatically.
For computers connected on this router’s LAN port, the Wake on LAN function allows you to turn on a computer through its MAC address. The computer must support Wake on LAN. Please check the BIOS setup in your computer. To wake up a computer, please enter the MAC address of the computer, and then click Wake Up to turn on the computer or click Cancel to aboard and clear the setting. 4.7 Status & Log Status & Log provides many useful information of the system.
System Up Time: This field shows the lasting time from the last time this system up to current. WAN Interface Connection Type: This field shows the WAN connection type this system is using. IP Address: This field shows the IP address of the system WAN port.
Subnet Mask: This field shows the subnet mask of the system WAN port. Default Gateway: This field shows the gateway of the system WAN port. DNS Servers: This field shows the DNS server IP address of the system WAN port. MAC Address: This field shows the MAC address of the system WAN port. Connection Status: This field shows the current WAN connection status. The value would be Connected or Not connected. LAN Interface IP Address: This field shows the IP address of the system LAN port.
IP addresses to other network devices. This page shows the IP address offered and to which MAC address does this IP address offered. Refresh: Click Refresh to get the latest information of the DHCP leases 4.7.3 System Log The system records some of its activities automatically. An alerting email could be send to inform users when the system log is full. The logged information can be saved to computer manually.
System Log: The log records the time, type of services and description of router activities. Send an alert when logs are full: Select an option to enable or disable alerting email. If enabled, the system will send an email to the designated email address when logs are full. Email Address: Input the email address that you want the alerting email to be sent to. Outgoing Mail Server: Input the outgoing mail server address.
Input the password of your mail server authentication. Save: Click Save to save the logs to your computer. Mail Now: Click Mail Now to send an alerting email immediately. Refresh: Click Refresh to get the latest log status. 4.8 Logout To logout from router web page, click Logout at the very right of the main menu. A page will inform you that your logout has completed. If you want to login again, click Login.
Appendix Factory Default Values IP Configuration WAN Connect Type: WAN DNS: PPPoE’s MTU: LAN IP: LAN Subnet Mask: DHCP Server: DHCP Server Starting IP Address: DHCP Server Ending IP Address: RIP: Web Server Port: Ping from WAN: Web Access from WAN: Print Server Access from WAN: FTP Access from WAN: Webcam Access from WAN: DDNS: Automatic IP Automatic 1492 192.168.1.100 255.255.255.0 Enabled 192.168.1.1 192.168.1.
NTP Server: Time Zone: time.nist.
