Owner`s manual

“Private” Call Pass Thru (Code 74)

Using Code 74 can allow “Private” type calls with No Number displayed to ring through to the TEL phone

port while still blocking Out of Area and stored numbered calls. To enable Private Call Pass Thru, enter

programming: then enter 74, when “Enter Code” displays. To turn this feature Off, when the prompt for

“Enter Code” displays enter 75, display shows function.

“Out of Area” Call Pass Thru (Code 76)

Using Code 76 can allow “Out of Area” type calls with No Number displayed to ring through to the TEL

phone port while still blocking Private and stored number calls. To enable Out of Area Call Pass Thru,

enter programming: then enter 76, when “Enter Code” displays. To turn this feature Off, when the

prompt for “Enter Code” displays enter 77, display shows function.

Dial Displayed Number (Code 91)

The DIAL button can be used to dial the number displayed of someone who has called in using the Arrow

Up and Down buttons to select a specific caller. The default operation of the Call Blocker is to prompt

you to either add or remove the “1” (USA Country Code) before the Call Blocker dials the number. The

prompt will ask “Dial 1?” and to answer that prompt use the Up arrow key for YES and the Down arrow

key for NO. After selecting an answer the Call Blocker will dial the number afterwhich the display will

prompt you to “Pick Up Phone”. To disable the Dial 1 prompt enter programming: press and hold the

Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt

for “Enter Code” displays enter 90, display shows function. To return to the (default), enter

programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then

“Pick Up Phone”, when the prompt for “Enter Code” displays enter 91, display shows function.

Display All Operating Codes (Code 92)

Press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”,

when the prompt for “Enter Code” displays, enter 92 to see the current settings.

Reset Call Blocker User Settings (Code 99#*)

To reset the Call Blocker’s user settings to factory settings but not delete any call lists, Press and hold the

Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt

for “Enter Code” displays, enter 99 # *.

LED Flashing (Code 28)

The Call Blocker’s red LED comes from the factory set to flash for new calls, ringing, blocked calls and

programming prompts. If you do not want to see the LED flashing at all, you can disable it with Code 29.

Press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”,

when the prompt for “Enter Code” displays, enter 29. To re-enable the LED flashing, enter 28.

Wildcarding (#)

When using the block or invite commands, you can use the # key to represent all numbers in a phone

number’s column. In the phone number ex. 602 555 1212, if you want to block or invite all numbers (0-

9) in a single column you would insert the # key in that column. Examples: To block all numbers (0-9) in

the last column, you would use 40 602 555 121#. To invite all numbers in the area code 602, use 50

602 ### ####. To block all numbers in the exchange 555 (example above) use 40 602 555 ####.

Call Blocker Compatibility

Digitone’s Call Blocker 10 works with all makes of analog telephony equipment and on all U.S. Domestic

and Foreign standard 2-wire telephone lines with FSK/DTMF (ETSI) Caller ID, DSL, FIOS, VoIP, Cable

Modems and Digital services using (ATA) adapters from Skype™, Vonage™, Ooma™ or Magic Jack™*.

* All trademarks, trade names, service marks and logos of respective manufacturers referenced herein

are registered trademarks of their respective companies.