Owner`s manual

Programming Numbers - Invited, VIP and Blocked (con’t)
Global Block Method and Code 97 # * - “I want to Block all callers and just allow certain numbers”.
Note from the factory, all callers with a number displayed are already invited and can ring through, but
you can create your own caller list by disabling the Global Invited List. You can then invite preferred
callers using the Invite Button on the front panel or through programming. To enable this feature, press
and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when
the prompt for “Enter Code” displays enter 97 #*, display shows function. NOTE: that when Code 97
#* is stored, all calls will be Blocked, answered and hungup on until you add Invited numbers. When
the prompt for “Enter Code” displays, enter 50 or 60 (VIP) to store an invited number or area code, then
the * key. Ex. for individual numbers enter: 60, 602 555 1212 , or for area codes enter: 50, 602* display
shows function. Store up to 30 numbers or area codes using Code 50 and up to 30 numbers or area
codes using Code 60. A total of 60 invited numbers or area codes can be stored.
Caller List Deletion
WARNING: This will delete all numbers from all lists! To delete ALL numbers stored, enter
programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then
“Pick Up Phone”, when the prompt for “Enter Code” displays, enter 98 # *, display shows: “ALL NBR
DELETED”. All numbers stored from all lists will be cleared.
Operating Modes
You can switch between the operating modes using the programming button and by entering one of the
mode numbers. The Call Blocker can toggle between the modes Standard, Business or Standby using
one of the settings. Note: After Hours Mode runs together with only Standard or Business Mode when
either mode is enabled. Mode settings are displayed only when entering Programming Mode.
Standard (default) Mode = Code 30
When calls come in, all phone numbers that are Invited will ring phones throughout your home/office like
normal and to the TEL phone port on the back of the Call Blocker, except for Anonymous, Out Of
Area, Private and Unknown callers showing no phone number. These calls will be answered by the
Call Blocker for processing and by default be hung-up on unless program Code 72 is enabled to allow
these call types to ring in. Blocked callers will be immediately answered and after eight seconds, get
hung-up on. To enable this (default) Mode, press and hold the Program Button for 3 seconds until you
see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code” displays enter 30, display
shows function. You can use Code 76 to override the block function for Out of Area + no number call
types or Code 74 to override the block function for Private + no number call types. These two codes will
allow those callers you need to hear from Out of Area (overseas) or Private (neighbors) to ring through.
You can also use Code 52 to invite up to 10 callers within a blocked area code.
Business Mode = Code 31
If you are running a business and want to hear from Anonymous, Out Of Area, Private and Unknown
callers as well as any other type of call, you can enable Business Mode Code 31 to allow calls through to
the TEL phone port except those you want to block. This mode also works with your phone company’s
voice mail but also blocks those phone numbers you have entered into the Blocked Callers List. Blocked
callers will be immediately answered and after eight seconds get hung-up on. To enable this Mode,
press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”,
when the prompt for “Enter Code” displays enter 31, display shows function.
Standby Mode = Code 32
In Standby, the TEL phone port will be connected directly to the telephone line and phones connected
there will ring. This feature allows you to leave the Call Blocker off whenever you like without
disconnecting the device and the RED light will blink slowly. To enable this Mode, press and hold the
Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for
“Enter Code” displays enter 32, display shows function.
6