Owner`s manual

Operating Modes
You can switch between the operating modes using the programming button and by entering one of the
mode numbers. The Call Blocker can toggle between the modes Standard, Business or Standby using
one of the settings. Note: After Hours Mode runs together with only Standard or Business Mode when
either mode is enabled. Mode settings are displayed each time the phone is placed On-Hook (hung-up).
Standard (default) Mode = Code 30
When calls come in, all phone numbers that are Invited will ring phones throughout your home/office like
normal and to the PHONE Port on the back of the Call Blocker, except for Anonymous, Out Of Area,
Private and Unknown callers showing no phone number. These calls will be answered by the Call
Blocker for processing and by default be hung-up on unless program Code 72 is enabled to allow these
call types to ring in. Blocked callers will be immediately answered and after eight seconds, get hung-
up on. To enable this (default) Mode, press and hold the Program Button for 3 seconds until you see
“Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code” displays enter code 30,
display shows function.
Business Mode = Code 31
If you are running a business and want to hear from Anonymous, Out Of Area, Private and Unknown
callers as well as any other type of call, you can enable Business Mode Code 31 to allow calls through to
the Phone Port except those you want to block. This mode also works with your phone company’s voice
mail but also blocks those phone numbers you have entered into the Blocked Callers List. Blocked
callers will be immediately answered and after eight seconds get hung-up on. To enable this Mode,
press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”,
when the prompt for “Enter Code” displays enter code 31, display shows function.
Standby Mode = Code 32
In Standby, the Phone port will be connected directly to the telephone line and phones connected there
will ring. This feature allows you to leave the Call Blocker off whenever you like without disconnecting the
device and the RED light will blink slowly. To enable this Mode, press and hold the Program Button for 3
seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code” displays
enter code 32, display shows function.
After Hours Mode - Programmable Time Feature Introduction
During a certain time of the day or night you can set the Call Blocker to enter into After Hours Mode.
This mode is designed to keep phones connected to the Phone port from ringing and allow calls to be
answered by an optional answer machine when it is enabled on a daily basis. If you run a business, then
you would use this After Hours Mode so all callers can leave a message. If your work or dinner times are
different from regularly scheduled times, you would use this mode so that you can get your sleep or to
completely avoid disruptive callers. During After Hours Mode, VIP callers can ring through at any
time regardless of the After Hours time settings. Invited callers can only ring through normally when
After Hours Mode is not enabled.
To use the After Hours Mode, you must first understand military time presented here. The clock on the
Call Blocker display converts the telephone company’s supplied clock data into either AM or PM time. If
the morning hours are 1:00am = 0100 hours, 2:00am = 0200 hours, etc. until noon = 1200 hours and
then the afternoon hours are 1:00pm = 1300 hours, 2:00pm = 1400 hours, etc. until midnight = 2400
hours. So, to set a time for a business after hours beginning in the early evening until the next morning
or 5:00pm to 8:00am you would use the military time of 1700 and 0800 as the two numbers for your
After Hours settings. To set a time for dinner in the evening from 6:00pm to 8:00pm you would use the
times of 1800 and 2000. To set a time for early morning until lunch time or 1:00am to 12:00pm you
would use 0100 and 1200.
Monday thru Friday – Start & End Times
Using military time as shown above, set this feature on by enter programming: press and hold the
Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt
for “Enter Code” displays enter Code 82, then “Enter Start Time” displays, enter the Start time of day
5