Owner`s manual

Changing Number of Rings To A Port (Code 8+)

The PrivacyCall defaults to 5 rings to each port for all functions. If you want to increase or decrease this

number of rings, then enter programming with your phone in any port and PRESS ## then PRESS 8,

then the number of rings you want, Ex. 4 or 5 or 6, etc. hear <Beep><Beep>.

Hang-up All Uninvited Callers (Code 601)

PrivacyCall can terminate each call that has no dialed entry from your caller. This mode will block all

telemarketing calls and will not ring your answer machine. Regular Invited callers will get through and

can leave a message, while all others cannot. To enable the Hang-Up Mode, use your phone in any port

and PRESS ## then PRESS 601 hear <Beep><Beep>. To return to allowing some calls through to your

answer machine, PRESS ## then 600.

Intercom Between Ports with Transfer Command

PrivacyCall can intercom phone devices between ports off the main telephone line by using the transfer

command of # * and the port you are calling. From Port 1 you can call Ports 2/3 or Port 4 and cause the

phones there to begin ringing. This is useful for calling from one room or floor to another if you have

installed the PrivacyCall with individual cabling from each port. This is also helpful for testing to see if the

phones ring or for sending a fax scan to a modem. The fax machine can be used as a scanner when

transferring the call to your modem. Just have the fax modem connected to port 3 auto answer the call.

PrivacyCall Standby Mode (Functions Off)

To change to Standby Mode, use your phone in any port and PRESS ## then PRESS 90 hear <Beep>

<Beep>. To turn PrivacyCall back ON, PRESS ## then 91. Note: All four ports (phones, fax, etc.) will ring

in Standby Mode. This feature allows you to leave PrivacyCall off whenever you like without disconnecting

the device and the RED light will blink slowly.

Changing Privacy Codes for Extensions 1, 2, 3 or 4

To change the access code to any extension, use your phone in any port and PRESS ## then PRESS 3

then enter the extension number you are changing. If it's Extension 1, PRESS 1; if it's Extension 2, PRESS

2, etc., hear <Beep>; then enter the access code you desire for that extension; when finished, PRESS *

hear <Beep><Beep> (sample string: 3, 1, 567,* = Access code changed to 567 for Extension 1). Note:

you cannot start all ports with the same extension number or change an extension number to the same

number that is already in use on another port. Ex. Code 2 cannot be used on Port 1 when it is already

installed on Port 2. You must uninstall the code in use at that port first to install the code you want.

Remote Access (PIN)

PrivacyCall can be remotely accessed for personal use or Digitone service work if you install a PIN code

using Code 0. You can enter a PIN code at any time after you have established # # Beep. To do this,

enter 0, hear <beep>, then a four to six digit number followed by *, hear <beep> <beep>. From then

on you must always enter this PIN to access programming. To access programming remotely, call into

the PrivacyCall and enter # #, then your PIN and hear <beep> <beep>. You are now in programming

mode just as though you were locally connected. Once connected, you can make changes as necessary,

for example, changing the forwarding number or adding or deleting a number to the caller list.

PIN Code Reset

You can also reset this PIN code in the event you accidentally install one and either don’t know you have

installed it or forgot the code. You would notice this problem if you tried to enter programming and can’t

get it to Beep after entering # #. To reset the code enter # # then enter 0 (zero) one at a time