DECLARATION OF CONFORMITY Manufacturer’s Name: Manufacturer’s Address: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: HardWire SC-2 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.) conforms to the following Product Specifications: Safety: IEC 60065 (7th ed.
WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty: The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
Introduction More than a remarkable achievement, HardWire™ represents a collection of significant improvements in effects pedals for guitar. HardWire pedals provide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers to provide such distinguishing features as true bypass and high voltage operation, making them essential additions to the signal chain of players who know about sound quality and demand the utmost in performance.
1 2 3 4 5 6 11 7 8 8 9 10
What Does This Do? 1. Level Knob - Controls the distortion output level. Turn the knob clockwise to increase and counter-clockwise to decrease the output level. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack. Use the proper supply for your area’s mains line voltage. 3. Low Knob - Controls the level of low frequency (bass) boost/cut. Turn the knob clockwise to increase and counter-clockwise to decrease the bass level. 4.
6. Voicing Switch - This switches between the Distortion’s two voicings. Crunch provides a classic balanced distortion. Saturated features an extra gain stage for maximum sustain distortion making it ideal for solos. 7. Input - Connect your instrument or the output of another pedal to this jack. This jack enables battery power to the pedal when connected. To prolong battery life, disconnect the cable from the Input jack when not in use.
10. Foot Switch - Turns the effect on and off. 11. Output - Connect this output to the input of your amplifier or the input of another pedal. Note: Use unbalanced mono instrument cables only.
Amplifier Setup PS200R (optional) or
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: . Using the tip of a 1/4” guitar cable, push in one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. .
Switch is properly fastened, both Release Pins are flush with the outer side of the pedal.
HardWire Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap.
Hook-and-loop Pedalboard Pad To . 2. . 10 attach the Pedalboard Pad, do the following: Peel off the existing rubber skid pad from the bottom of the pedal. Peel the adhesive protector from the back of the Pedalboard Pad. Apply the Pedalboard Pad to the bottom of the pedal.
Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: . Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
StompLock To . 2. . 12 place the StompLock over the pedal knobs, do the following: Set the knobs to your preferred setting. Gently push the StompLock over the top of the knobs. To remove the StompLock, gently lift one side and then the other.
Specifications Controls - Level, Low, High, Gain, Voice Switch, On/Off Pedal Jacks - Input, Output Input Impedance - >500 kΩ - effect on Output Impedance - 1 kΩ - effect on Input Impedance - true hardwire bypass - effect off Output Impedance - true hardwire bypass - effect off Power Supply - 9V Alkaline Dry Battery or Harman PS200R 9V DC power supply Current Draw - 20 mA (typical at 9V DC) Power Consumption - 180 mW (typical w/optional PS200R power supply) Dimensions - 5.25”(L) x 3.5”(W) x 2.
8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 HardWire and DigiTech are trademarks of the Harman Music Group Inc. Copyright - Harman Music Group Manufactured in the USA HardWire SC-2 Owners Manual 18-0666-A Please visit us on the World Wide Web at: www.digitech.
