User’s Guide
Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products.
Warranty We at DigiTech are very proud of our products and back-up each one we sell with the following warranty: 1.The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. Digitech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3.
Section-1 Introduction Getting Acquainted Congratulations on your purchase of the RP300.You now have the most complete guitar processing system ever available.With the flexibility, and power included in the RP300, your sound creations are as unlimited as your imagination. The features and functions of the RP300’s knob based matrix editing system are extremely user friendly.
A Guided Tour of the RP300 The Front Panel WHAZUP30 1. Up/Down Footswitches - These 2 Footswitches are used to select Presets, access the Tuner, or bypass the RP300.The Footswitch on the left will decrease, and the middle Footswitch will increase the Preset number. Pressing both Footswitches together will bypass the currently selected Preset. Pressing and holding both Footswitches will access the Tuner. 2.
7. Display - The Display provides information for different functions depending on the mode that is active. In Performance mode, the Display will show the currently selected Preset name and numeric location. In Edit mode, the Display will show the name and value of the selected parameter. In Tuner mode, the Display will show the note being played and whether the note is sharp, flat, or in tune. 8. Store - The Store button is used to save your custom edits to the user Presets. 9.
Getting Started Making Connections There are several different connection options available with the RP300. Before connecting the RP300, make sure that the power to your amplifier and the RP300 is turned off.There is no power switch on the RP300.To turn the RP300 on or off, simply connect or disconnect the included PS0913B power supply from the Power Jack to an AC outlet. Mono Operation Connect your guitar to the Input of the RP300.
Applying Power Before applying power to anything, set your amp(s) to a clean tone and set the tone controls to a flat EQ response (on most amps, this would be 0 or 5 on the tone controls).Then follow the steps listed below. 1.Turn the amp volume all the way down. 2. Connect the plug of the PS0913B power supply to the Power Jack on the rear panel of the RP300. 3. Connect the other end of the PS0913B power supply to an AC outlet. 4.
About the RP300 The Presets Presets are named and numbered locations of programmed sounds which reside in the RP300. Presets are recalled with the Footswitches.The active effects in each Preset will be indicated by the lighted LEDs in the Effect Matrix.The RP300 comes with 40 User Presets (Presets 1-40) and 40 Factory Presets (Presets 41-80).The User Presets are locations where your creations may be stored.The Factory Presets will not allow you to store any changes to them.
Learn-A-Lick Mode Learn-A-Lick allows you to record a 10 second passage of music and play it back as slow as 1/4 speed with no change in pitch. This is useful for picking out the notes of a fast solo passage.
Section Two - Editing Functions Editing/Creating Presets Creating your own signature sound with the RP300 is easy and intuitive.The RP300 lets you create your own Presets, or fine tune existing Presets to suit your needs. When creating or editing a sound, you must first start with one of the User or Factory Presets. It is not possible to start with a completely empty Preset.
Storing/Copying/Naming a Preset Once the Preset has been modified to your liking, you may store your settings to any of the 40 User Preset locations (Presets 1-40). The following steps outline the procedure for storing changes to a Preset or copying a Preset to a different location: 1. Press the Store button once.The Store button LED will blink and the first character in the Display will Flash indicating that you can now name your custom creation. 2.
Section Three - Effects and Parameters About the Effects The RP300 can be thought of as several different “virtual” amplifiers and individual, hi-tech stomp boxes in a single programmable package.With stomp boxes, the order in which they are connected can drastically affect the overall sound quality.The RP300 has placed the Effects in an order for optimum sound quality.The following diagram shows the order of the effects contained in the RP300.
Compressor A Compressor is used to increase sustain, tighten up the guitar signal, and prevent the signal from clipping the input of other effects. It sets a maximum boundary (Threshold) for the strength of a signal. If a signal exceeds the Threshold, it is squeezed back into compliance based upon the compression Ratio setting. Comp On/Off - The Number 1 Knob turns the Compressor on (ON) and off (OF).
DIRECT - Cabinet Off 1X12 1 - 1x12 Mic 1 1X12 2 - 1x12 Mic 2 1X12 3 - 1x12 Mic 3 1X12 4 - 1x12 Mic 4 2X12o 2X12o 2X12o 2X12o 1 2 3 4 - 2x12 2x12 2x12 2x12 Open Open Open Open 2X12c 2X12c 2X12c 2X12c 1 2 3 4 - 2x12 2x12 2x12 2x12 Closed Closed Closed Closed Back Back Back Back Mic Mic Mic Mic Back Back Back Back 1 2 3 4 Mic Mic Mic Mic 1 2 3 4 4X12V 4X12V 4X12V 4X12V 1 2 3 4 - 4x12 Vintage 4x12 Vintage 4x12 Vintage 4x12 Vintage Mic Mic Mic Mic 1 2 3 4 4X12B 4X12B 4X12B 4X12B 1 2 3 4 -
Gate Threshold - The Number 4 Knob sets the signal strength required to open or close the Noise Gate.The Gate Threshold parameter ranges from 1 (opens easily) to 40 (requires strong signals to open). Pluck Sensitivity - The Number 5 Knob controls the point where the Gate re-triggers when using the Pluck type Noise Gate.This Parameter is only available when Pluck is the selected type of Noise Gate. Ranges from 1 (requires strong signals to re-trigger) to 99 (re-triggers with weak signals).
Parameter 2 - The Number 3 Knob adjusts the strength the signal must be (Sensitivity) in order to trigger the Flanger. Ranges from 1 (requiring strong signals to trigger) to 99 (triggers with weak signals). Parameter 3 - The Number 4 Knob selects the point at where the Flanger will begin it’s sweep (LFO Start). Ranges from 0 to 99. Mod Level - The Number 5 Knob controls the mix of wet and dry signal. Ranges from 0 (all dry) to 99 (all wet).
Vibrato (viBRTO) A Vibrato effect modulates the pitch of the incoming signal at an even rate. Parameter 1 - The Number 2 Knob adjusts the rate (Speed) at which the pitch modulates. Ranges from 1 to 99. Parameter 2 - The Number 3 Knob adjusts the intensity (Depth) of the modulating pitch. Ranges from 1 to 99. The Number 4 and 5 knobs have no function when the Vibrato is selected. Rotary Speaker (ROTARY) Rotary Speaker is an emulation of a device that included a spinning horn and rotor (woofer).
SynthTalk™ (syNtLK) SynthTalk™ is another effect exclusive to DigiTech. It makes your guitar seem to speak based upon the dynamics of your playing style. Parameter 1 - The Number 2 Knob adjusts the Attack of the synthesized voice. Ranges from 1 to 99. Parameter 2 - The Number 3 Knob adjusts the Release of the synthesized voice. Ranges from 1 to 99. Parameter 3 - The Number 4 Knob changes the characteristics of the various synth voices. Ranges from 0 to 99.
Whammy (no Dry Signal) 1OCTUP (1 octave above) 2OCTUP (2 octaves above) 2NDDWN (a second below) REV2ND (a second below reversed pedal action) 4THDWN (a fourth below) 1OCTDN (an octave below) 2OCTDN (2 octaves below) DIVBOM (Dive Bomb) Harmony Bends (Dry Signal Added) M3>MA3 (a minor third to a Major third) 2NDMA3 (a second above to a Major third above) 3RD4TH (a third above to a fourth above) 4TH5TH (a fourth above to a fifth above) 5THOCT (a fifth above to an octave above) HOCTUP (one octave above) HOCTDN
Section Four - Other Functions Expression Pedal The Expression Pedal on the RP300 can be assigned to control the RP300’s Volume, Whammy™,Ya Ya™, or just about any other parameter in real time with your foot. When a parameter has been assigned to the Expression Pedal, a programmable minimum and maximum value can also be assigned.The procedure for assigning a parameter to the Expression Pedal is as follows: 1.
V-Switch The RP300’s Expression Pedal includes DigiTech’s exclusive V-Switch.The V-Switch allows the Expression Pedal assignment to be switched on the fly. Applying extra pressure to the toe of the Expression Pedal will engage the V-Switch and the function of the Expression Pedal will switch between the assigned parameter and Wah. The sensitivity or amount of pressure required to engage the V-Switch can be adjusted to suit your personal taste (or weight of your foot).
REVLVL (Reverb Level) - The LFO controls the Reverbs Mix Level. VOLPRE (Volume Pre) - The LFO controls the Volume after the Amp Modeling but before the Effects. VOLPST (Volume Post) - The LFO controls the Volume at the end of the Effects chain. 4. Rotate the Number 3 Knob to select the minimum value the assigned parameter will reach at the bottom turn around point for the LFO (not available when volume is the assigned parameter). 5.
V-Switch Sensitivity If you wish to adjust the sensitivity setting of the V-Switch, follow steps 1 through 7 for Calibrating the Expression Pedal and then follow the steps listed below: 1.When the Display reads VSWTCH, rock the Expression Pedal forward (toe down) and apply extra pressure on the toe of the Pedal until the Display reads DONE. 2.
Section Five - Appendix Factory Preset List 22
Specifications Input: 1/4" TS Jam-A-Long: 1 - 1/8” Stereo TRS Outputs: 2 - 1/4” TS Headphone: 1/8” Stereo TRS A/D/A: 24 bit Delta Sigma Power Supply: 9 VAC, 1.
DigiTech 8760 S. Sandy Parkway, Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 International Distribution 8760 S. Sandy Parkway, Sandy, Utah 84070 USA PH (801) 566-8800 FAX (801) 566-7005 DigiTech and RP300 are trade marks of the Harman Music Group Inc. Copyright the Harman Music Group Printed in the USA 01/2001 Manufactured in the USA RP300 Owners Manual 18-6383-A Please visit DigiTech on the World Wide Web at: http://www.digitech.
