Owner`s manual
better dynamics. Ratio settings are:1.2:1 (¡2-1),1.5:1 (¡5-1),1.8:1 (¡8-1), 2:1 (™0-1), 2.5:1
(
™5-1),3:1 (£0-1), 4:1 (¢0-1), 5:1 (∞0-1), 8:1 (•0-1),10:1 (10-1), 20:1 (20-1),and Infinity:1
(
INFnty-1).
Threshold - Knob 3 selects the Threshold (
threshld). The Threshold is the level a signal is allowed to
reach before the compressor begins to work. Low Threshold settings activate the
compressor with weaker signals. Higher settings require a stronger signal to activate
compression. Ranges from
0 to 99.
Gain - Knob 4 adjusts the Output Gain (
CMP Gain) from the Compressor. This parameter is used to
balance the level of the Compressor to reach unity gain. Other effects can clip if the Compressor
Gain too high. Ranges from
0 to 20(dB).
Knob 5 has no function when the Compressor is selected.
Whammy
™
/IPS/Talk
This module includes four types of pitch altering effects:Whammy, IPS, Detune, Pitch Shift, and the Talker
™
effect. Only one of the effects in this row can be used at a time. After selecting the type of effect in this
module, the Knobs 2-5 can then be used to adjust the individual parameters associated with the selected
effect. The following pages describe each effect and their parameters in more detail.
Whammy/IPS/Talk On/Off -When the Whammy/IPS/Talk effects module is selected the Status
button turns the Whammy/IPS/Talk effects on and off.
Whammy/IPS/Talk Select - Knob 1 selects whether the module is a Whammy (WHAMMY), Intelligent
Pitch Shifting (IPS),Detuner (DETUNE), Pitch Shift (PITCH), or Talker
(Talker 1-5).
Whammy
Whammy is an effect that uses an Expression Pedal to bend the pitch of the incoming signal,or add a
bendable harmony with the original signal. As the Pedal is moved, the note bends either up or down.
When Whammy is selected, it is automatically placed before the Amp Modeling as shown in the block
diagram (see page 34). The Whammy effect must be linked to the Expression Pedal in order to
function. See page 45 for more information on linking the Expression Pedal.
Parameter 1 - Knob 2 selects the interval and direction of the pitch bend.Choices are as follows:
Parameter 2 - Knob 3 provides a manual control of the Whammy Pedal (
wham pdl) position.
Ranges from
0 to 99.
Knob 4 has no function when the Whammy is selected.
Level - Knob 5 adjusts the Whammy Mix (
Wham mix) of all of the pitch-altering effects in this
module. Ranges from
0 to 99.
Whammy (no Dry Signal)
1 OCT UP (1 octave up)
2 OCT UP (2 octaves up)
2NDDOWN (a second down)
REV2NDDN (a second down reversed pedal
action)
4TH DOWN (a fourth down)
1 OCT DN (an octave down)
2 OCT DN (2 octaves down)
DIVEBOMB (Dive Bomb)
Harmony Bends (Dry Signal Added)
M3->MAJ3 (a minor third to a Major third)
2ND->MAJ3 (a second above to a Major third
up)
3RD->4TH (a third above to a fourth up)
4TH
->5TH (a fourth above to a fifth up)
5TH->OCT (a fifth above to an octave up)
H OCT UP (one octave up)
H OCT DN (one octave down)
octup->Dn (one octave up to one octave
down)
36
Effects and Parameters