HARDWIRE SC-2 VALVE DISTORTION OWNER’S MANUAL
DECLARATION OF CONFORMITY Manufacturer’s Name: Harman Signal Processing Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: SC-2 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
WARRANTY: We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty: 1. Please register online at www.digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in the United States. 2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
Introduction More than a remarkable achievement, DigiTech’s HardWire® series represents a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control.
Pedal Interface 1 2 3 4 5 6 11 7 8 8 9 10 2
What Does This Do? 1. Level Knob - Controls the distortion output level. Turn the knob clockwise to increase and counter-clockwise to decrease the output level. 1. DC Adapter Jack - Connect the optional Harman power supply to this jack. Use the proper supply for your area’s mains line voltage. 2. Low Knob - Controls the level of low frequency (bass) boost/cut. Turn the knob clockwise to increase and counter-clockwise to decrease the bass level. 3.
4 4. Gain Knob - Controls the overall distortion gain. Turn the knob clockwise to increase and counter-clockwise to decrease the amount of distortion gain. 5. Voicing Switch - This switches between the Distortion’s two voicings. Crunch provides a classic balanced distortion. Saturated features an extra gain stage for maximum sustain distortion making it ideal for solos. 6. Input - Connect your instrument or the output of another pedal to this jack.
8. Indicator LED - Lights when the effect is turned on. When battery power is low (approximately 15 minutes before it dies), the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery. 9. Foot Switch - Turns the effect on and off. 10. Output - Connect this output to the input of your amplifier or the input of another pedal. Note: Use unbalanced mono instrument cables only.
Amplifier Setup Harman Power Supply (optional) or 6
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1. Using the tip of a 1/4” guitar cable, push in one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. 3.
into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both Release Pins are flush with the outer side of Foot Switch the pedal.
Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap.
Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal.
Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
StompLock To place the StompLock over the pedal knobs, do the following: 1. Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. 3. To remove the StompLock, gently lift one side and then the other.
Specifications Controls: Jacks: Input Impedance: Output Impedance: Input Impedance: Output Impedance: Power Supply: Current Draw: Power Consumption: Dimensions: Weight: Optional Power Supply: Power Supply Polarity: Power Supply Output: Level, Low, High, Gain, Voice Switch, On/Off Pedal Input, Output >500 kΩ - effect on 1 kΩ - effect on True hardwire bypass - effect off True hardwire bypass - effect off 9 V Alkaline Dry Battery or Harman power supply 20 mA (typical at 9 VDC) 190 mW (typical w/optional powe
8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 DigiTech® and HardWire® are registered trademarks of Harman Designed in the USA Copyright - Harman Printed in China HardWire SC-2 Owners Manual 5024340-B Please visit our website at: www.digitech.
