DECLARATION OF CONFORMITY Manufacturer’s Name: Manufacturer’s Address: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: HardWire CR-7 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.) conforms to the following Product Specifications: Safety: IEC 60065 (7th ed.
WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty: The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
Introduction More than a remarkable achievement, HardWire™ represents a collection of significant improvements in effects pedals for guitar. HardWire pedals provide a suite of well-known effects, each with superior tone and control.
1 2 3 4 5 11 6 12 7 8 8 9 10
What Does This Do? 1. Level Knob - Controls the chorus level. Turn this knob clockwise to increase and counter-clockwise to decrease the chorus level. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack. Use the proper supply for your area’s mains line voltage. 3. Speed Knob - Controls the modulation speed of the chorus effect. Turn the knob clockwise to increase and counter-clockwise to decrease the speed. 4. Depth Knob - Controls the intensity of the chorus effect.
MODERN – dual voice chorusing that’s both very rich and smooth. BOUTIQUE – a rich chorus with the quirkiness of analog circuits. ANALOG – distinctively organic bucket-brigade chorus. JAZZ – single voice chorusing with a dry output – jazzers rejoice! VINTAGE – warm and versatile from subtle to euphoric. 6. Input 1 (Mono) - Connect your instrument, additional pedal, or an amp effects send to this jack. Signals are heard at both outputs when only the Input 1 (Mono) jack is used.
7. Input 2 - Connect a second input to this jack for stereo operation. Inputs 1 and 2 are processed separately through the stereo chorus effect and then fed to Outputs 1 and 2 keeping true stereo separation between channels. 8. Foot Switch Release Pins - These two pins are spring loaded hinges that hold the Foot Switch in place. See page 9 for information on accessing and changing the battery. 9. Indicator LED - Lights when the effect is turned on.
12. Output 2 - Connect this output to a second guitar amplifier when two amplifiers are being used. Note: Use unbalanced mono instrument cables only.
Amp Setup PS200R (optional) or
Effects Loop Setup AMP RETURN PS200R (optional) AMP SEND Note: If the amp effects loop has a mix control, set the mix to 100% full wet.
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: . Using the tip of a 1/4” guitar cable, push in one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. . Remove the battery from the battery compartment and disconnect the battery cable. .
Switch is properly fastened, both Release Pins are flush with the outer side of the pedal.
HardWire Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap.
Hook-and-loop Pedalboard Pad To . . . 12 attach the Pedalboard Pad, do the following: Peel off the existing rubber skid pad from the bottom of the pedal. Peel the adhesive protector from the back of the Pedalboard Pad. Apply the Pedalboard Pad to the bottom of the pedal.
Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: . Peel the adhesive backing from the Foot Switch Glow Sticker. . Apply the Glow Sticker to the top of the Foot Switch.
StompLock To . . . 14 place the StompLock over the pedal knobs, do the following: Set the knobs to your preferred setting. Gently push the StompLock over the top of the knobs. To remove the StompLock, gently lift one side and then the other.
Specifications Controls - Level, Speed, Depth, Type, On/Off Pedal Jacks - Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance - >1 MΩ (stereo), >500 kΩ (mono) - effect on Output Impedance - 1 kΩ - effect on Input Impedance - true hardwire bypass - effect off Output Impedance - true hardwire bypass - effect off Power Supply - 9V Alkaline Dry Battery or Harman PS200R 9V DC power supply Current Draw - 70 mA (typical at 9V DC) Power Consumption - 625 mW (typical w/optional PS200R power supply) D
8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 HardWire and DigiTech are trademarks of the Harman Music Group Inc. Copyright - Harman Music Group Manufactured in the USA HardWire CR-7 Owners Manual 18-0618-A Please visit us on the World Wide Web at: www.digitech.
