Installation guide

ManualsBrandsDigitaLinx ManualsComputer equipmentDL-HDM44

11675 Ridgeline Dr

Colorado Springs, CO 80921

Rev 140411

Phone: 719-260-0061

Toll-Free: 800-530-8998

Fax: 719-260-0075

DL-HDM44 Installaon and

Operaon Guide

Summary of content (24 pages)

PAGE 1
DL-HDM44 Installation and Operation Guide Rev 140411 11675 Ridgeline Dr Colorado Springs, CO 80921 Phone: 719-260-0061 Toll-Free: 800-530-8998 Fax: 719-260-0075
PAGE 2
DL-HDM44 Installation Guide 2
PAGE 3
DL-HDM44 Installation Guide Important Safety Instructions »» Please completely read and verify you understand all instructions in this manual before operating this equipment. »» Keep these instructions in a safe, accessible place for future reference. »» Heed all warnings. »» Follow all instructions. »» Do not use this apparatus near water. »» Clean only with a dry cloth.
PAGE 4
DL-HDM44 Installation Guide Table of Contents Product Overview �� 6 Package Contents �� 7 Front and Rear Panels �� 8 F
PAGE 5
DL-HDM44 Installation Guide Troubleshooting �� 21 Matrix does not power on �� 21 Cannot view 3D content �� 21 Cannot view 4K content
PAGE 6
DL-HDM44 Installation Guide Product Overview The Digitalinx DL-HDM44 is a four input by four output HDMI matrix switcher. The DL-HDM44 supports up to 4K video resolutions, Deep Color, and 3D video. The DL-HDM44 can be controlled via front panel buttons, front panel IR, external IR, RS232, and through a web browser when the matrix is connected to a network. The matrix includes a simple IR remote control to allow IR switching.
PAGE 7
DL-HDM44 Installation Guide Package Contents Please verify the following items are in the shipping box prior to installation of the DL-HDM44. DL-HDM44 Matrix Switcher 1 ea IR Receiver 1 ea Infrared Remote Control 1 ea Rack Ears 2 ea 5V DC 3.
PAGE 8
DL-HDM44 Installation Guide Front and Rear Panels Front Panel 1 2 3 POWER EDID 4 5 Inputs 1 B A C 2 3 4 D A B Part#: DL-HDM44 C 4x4 HDMI Matrix Switcher 1. 2. 3. 4. 5. Outputs D IR receiver for matrix control via IR remote Power button and LED EDID button and LED Output cycle buttons Matrix routing status LEDs Rear Panel A B INPUTS 1 C D E IR In RS232 Ethernet F OUTPUTS 2 3 4 A B C D Power DC5V Service A. B. C. D. E. F. G.
PAGE 9
DL-HDM44 Installation Guide IR Remote The included IR remote features discrete input selection buttons for each output. It also has a power toggle button to turn off the matrix when not in use. Please see page 15 for IR Remote Operation.
PAGE 10
DL-HDM44 Installation Guide Installation Instructions Quick Start 1. 2. 3. 4. 5. Mount the matrix Connect sources Connect displays Connect control (optional) Apply power Mount the Matrix At least 2 inches of free air space is required on both sides of the DL-HDM44 for proper side ventilation. Avoid mounting the DL-HDM44 near a power amplifier or any other source of significant heat.
PAGE 11
DL-HDM44 Installation Guide Connect Sources Connect the source devices to HDMI inputs using HDMI cables that are less than or equal to 5 meters in length. For source devices that are further away, it is highly recommended to install a Digitalinx DL-HD70 or DL-HDE100. Connect Displays Connect the display devices to HDMI outputs using HDMI cables that are less than or equal to 5 meters in length.
PAGE 12
DL-HDM44 Installation Guide Connect RS232 Control The RS232 control port requires a standard straight-through serial cable for operation. The default settings for the RS232 port are: • • • • 19200 baud 8 Data Bits 1 Stop Bit Parity = none See page 19 for all available control commands for the DL-HDM44. Connect a standard straight-through serial cable with DE9 connector between the RS232 port on the DL-HDM44 and the controller.
PAGE 13
DL-HDM44 Installation Guide Router Connection 1. 2. 3. Configure the router to use the same IP range as the matrix, such as 192.168.0.1. Connect the computer to the router. Connect the DL-HDM44 to the router Crossover Cable Connection 1. 2. Configure the computer to use the same network prefix as the IP address assigned to the matrix. For example, the IP address of the matrix is 192.168.0.178. Set the computer to use a static IP address within the same network range, such as 192.168.0.42.
PAGE 14
DL-HDM44 Installation Guide Apply Power Plug the power supply into the power input port on the rear of the matrix. Twist the collar of the power plug in a clockwise direction to secure the connection. Connect the IEC power cable into the power supply. The matrix will turn on once the IEC cable is plugged into AC power.
PAGE 15
DL-HDM44 Installation Guide Front Panel and IR Remote Operation Front Panel Operation To set a route using the front panel of the DL-HDM44, press the desired output button (display) until the preferred input source is selected. If output B is currently viewing input 4, the output B button would need to be pressed three times to view the content on input 3. IR Remote Operation The buttons on the IR remote will allow direct routing of inputs to a specific output.
PAGE 16
DL-HDM44 Installation Guide Web Browser Control Matrix Status Open a web browser and go to the IP address of the DL-HDM44. The default IP address is 192.168.0.178. The Matrix Status screen shows the power, output and EDID states of the DL-HDM44. Matrix Control Click the Matrix Control tab to access all the control options. A dropdown menu is available for power, output, and EDID settings. Once a selection is made, the matrix will immediately apply the requested change.
PAGE 17
DL-HDM44 Installation Guide Network Setting The Network Setting tab displays the network settings for the DL-HDM44, including the MAC address and static IP or DHCP settings. To apply the changes, click the Save button. A confirmation dialog box will open to verify the changes.
PAGE 18
DL-HDM44 Installation Guide EDID Management Pressing the EDID button on the front of the matrix or changing the option in the Matrix Control window will cycle between the built-in EDID (STD mode) or the EDID of the display connected to Output A (TV mode). The EDID LED will be lit on the front of the matrix when using the stock EDID. In STD mode, the EDID for the inputs of the DL-HDM44 is 1080p with stereo audio. When in TV mode, the DL-HDM44 will read the EDID settings of the display connected to Output A.
PAGE 19
DL-HDM44 Installation Guide RS232 Commands RS232 Settings: 19200 baud, 8 Data bits, 1 Stop bit, Parity = None x = Input Number (input 2 would be 2) y = Output Letter (output C would be C and must be in caps) = Carriage return (Hex 0D) = Space (Hex 20) A carriage return is required at the end of all command strings. Any changes made to the matrix via front panel, IR, or web browser will be replied on the RS232 port. Control via IP is not available on the DL-HDM44.
PAGE 20
DL-HDM44 Installation Guide EDID Commands Description Use built-in EDID Use EDID from Output A Command Response EM1 EM1 EM2 EM2 TCP/IP Setup Commands Description Set static IP address Set subnet mask Set gateway Command Response SETIP SETIP IP Address is set. SETNETMASK SETNETMASK NetMask Address is set.
PAGE 21
DL-HDM44 Installation Guide Troubleshooting Matrix does not power on »» Verify power outlet is active. »» Verify continuity in power cable. Cannot view 3D content »» Select TV mode in the EDID settings. »» Verify display is 3D compatible. »» Verify source device can output 3D content. Cannot view 4K content »» Select TV mode in the EDID settings. »» Verify display is 4K compatible. »» Verify source device can output 4K content. Cannot hear surround sound audio »» Select TV mode in the EDID settings.
PAGE 22
DL-HDM44 Installation Guide Technical Specifications I/O Connections HDMI Inputs HDMI Outputs IR Eye 5V DC Power Control, Rear Panel Control, Front Panel Four (4) HDMI Type A Receptacle Connector (1 per input) Four (4) HDMI Type A Receptacle Connector (1 per output) One (1) 3.5 mm jack (TRS) One (1) Threaded Barrel (5.5mm OD; 2.6mm ID) RS232 via DE-9, TCP/IP via 8P8C, IR via 3.
PAGE 23
PAGE 24
Thank you for your purchase. Please contact us with your questions and comments. 11675 Ridgeline Drive Colorado Springs, Colorado 80921 USA Phone: 719-260-0061 Fax: 719-260-0075 Toll-Free: 800-530-8998 www.libav.