Installation guide

Contents vii
C.2.5 Bringing a Newly Converted Dual-Host Conversion
On-Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–21
C.2.6 Final Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–22
Glossary
Index
Figures
1–1 Front View of the SF200 Storage Array . . . . . . . . . . . . . . . . . 1–2
1–2 SF72 Storage Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5
2–1 Single-Host System Configuration Sheet . . . . . . . . . . . . . . . . 2–2
2–2 Dual-Host System Configuration Sheet . . . . . . . . . . . . . . . . . 2–3
2–3 NEMA Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
3–1 Shipping Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
3–2 Ramp Installation on Shipping Pallet . . . . . . . . . . . . . . . . . . 3–5
3–3 Storage Array Removal from the Pallet . . . . . . . . . . . . . . . . . 3–7
3–4 Placing the SF200 Storage Array . . . . . . . . . . . . . . . . . . . . . . 3–9
3–5 Adjusting Leveler Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
3–6 Verifying the SF72 OCP Seating . . . . . . . . . . . . . . . . . . . . . . 3–11
3–7 Verifying the 881 Power Controller . . . . . . . . . . . . . . . . . . . . 3–12
3–8 SF72 Storage Enclosure Power Connection and Voltage
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14
3–9 Magazine Tape Subsystem Power Connection and Voltage
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–15
4–1 Verifying the SF72 DSSI ID Switch Settings . . . . . . . . . . . . . 4–8
4–2 Seating the SF72 OCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
4–3 Verifying the 881 Power Controller . . . . . . . . . . . . . . . . . . . . 4–11
4–4 SF72 Power Cords and Voltage Selection . . . . . . . . . . . . . . . . 4–13
4–5 Magazine Tape Subsystem Power Cords and Voltage
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
4–6 Removing Terminators and Connecting DSSI Cables at the
System I/O Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–17
4–7 Placing a Label on a DSSI Cable . . . . . . . . . . . . . . . . . . . . . . 4–21
4–8 Placing a Label on the OCP Door . . . . . . . . . . . . . . . . . . . . . . 4–22
4–9 Placing a Label on the Magazine Tape Subsystem . . . . . . . . . 4–23