85XX Series Network DVR User Manual……………………………………………………………………….V1.0 85XX Series Network DVR User Manual 8504/8504P 8508 H8504P/AH8504P H8508/AH8508 8504FP/8508F/A8504FP 8504CP/8508C/A8504CP /F8504FP/F8508F/A8508F F8504CP/F8508C/A8508C PLEASE READ CAREFULLY AND SAVE This manual contains important information about this product's operation. If you are installing this product for others, you must leave this manual for a copy with the end user.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 CONTENT CHAPTER 1 INTRODUCTION ............................................................................................... 4 1.1 MAIN FEATURE ............................................................................................................................................................. 4 1.2 PRODUCT FEATURES ....................................................................................................................
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Chapter 1 INTRODUCTION 1.1 Main Feature 85XX series DVR is 4CH D1 and 8CH CIF resolution digital video recorder. Both of them have local recording, playback, support treble code remote network surveillance, data backup, parameter setting, motion detection, I/O alarm setting, PTZ and USB mouse. 1.2 Product features Advanced Linux; H.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Video bit rate CIF: 384，512，768 Kbps HD1: 512，768,1024 Kbps D1：896，1024,1280Kbps Audio bit rate 32KB/s Data save mode Support SATA HDD Alarm Input 4CH/8CH Alarm input Alarm Output 1CH Alarm output Serial port Support 1 RS485 port Network port NET port, 10M/100M adapt network port Mouse USB2.0 USB Driver USB2.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 attention: 1. When install and operate the DVR, apply with the electrical standard request and connection requirement. 2. Make sure the power supply is connected to ground. 3. Do not touch the power supply adaptor and DVR in wet. 4. Do not drop the liquid onto the DVR device in order to avoid short circuit inside. 5. Do not lay on other heavy subjects to DVR. 6. Clear the DVR with soft cloth, and do not use chemical solvent. 7.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 2.1.2 Mouse Operation You can use mouse to make operation of the menu besides IR remote controller. (The operation is the same as PC Windows).Please inserts the mouse into USB Port. Click key right Enter into main menu: Click the right key on the live view. Click the left key to enter into the setting interface. Click the left key to zoom in the window on the live view and playback video.
5XX Series Network DVR User Manual……………………………………………………………………….V1.0 2.2 System Operation 2.2.1 START-UP Connect the power adapter to DVR. When start up the DVR, 【POWER】LED will be on and 4 images will be display on the screen. If it has setup ignition recording or time recording, the system will record automatically and the corresponding LED will be on, and the system work normally. Remark: 1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Device ID: You just need to enter the device ID as the right frame. Password: enter the admin password or user password. 2.2.3 GUI OPERATION The main menu include “SEARCH”,”RECORD”,”HDD”,”BASIC”，“ADVANCE”, and “Exit”. Remark: You must press “APPLY” to make the setting for submenu valid. It will be no use when exit directly.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The first two lines is for Month, and the below three lines is for Day. The green color block is general record; the red color block is alarm record. Double click the day then system will playback the record for whole day. If click “FILE LIST”, the system will show the record file list.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 USB mouse port; B. Loin system and enter SEARCH menu, click FILE LIST to show the record files; C. Select the record file you want to backup; D. Click BACKUP to backup the data. Please make sure the power supply is stable during backup, and make sure do not plug off the USB during backup. Remarks: If the free space of USB driver is not enough to save the backup data, the system will remind and show the space is not enough. 2.2.3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Switch: Set the channel in ON or OFF status, that is to set the channel is open or close status. Resolution: For 9504 DVR, there’re D1, HD1, CIF options; For 9508 DVR, in CH1 and CH2, there’re D1, HD1, CIF options; and other channel only with HD1, CIF options. Bitrate: There’re three options to be selected, L, M, H.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The time table shows one week and 0-23hrs in one day. Users could set the time duration as alarm record (Red), normal record (Green), and no recording (Blue). Schedule record steps: A. Select the TIMER RECORD in RECORD menu. B. Select the channel for schedule record. C. Select the record mode, like Alarm, Normal record in Red or Green color. D.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 HDD STATUS: SIZE: shows HDD total capacity. FREE SPACE: show the free space of HDD. AVAILABLE TIME: show the remaining recording time depends on the video packing time you set. OVERWRITE: there’re two options ENABLE or DISABLE. If in ENABLE, and if the HDD capacity is full, the system will overwrite the previous record automatically.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 SYSTEM LANGUAGE: Select the language and click APPLY, then system will restart. Now the system is available for multiple language firmwares, such as English, Russian, Spanish, French, Thai language etc. 2.2.3.4.2 DATE/TIME Date and Time setup: A. Input the date and time, and select the date format in TIME SETUP. Make sure the system date and time is the same with computer when need to remote access from outside internet.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 ·Default：In default, DST is from the 2nd Sun of March to 2nd Sun to November. (Skip to Step3) C. Select default, click “enter” to setup. D. Select user-defined mode, choose the corresponding week and month is OK. E. Click “APPLY” to save and exit. 2.2.3.4.3 PASSWORD When user starts the system in first time, system will identify with “000000” as the device serial number to login.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 User can change the device serial number, admin and user password in the password setting interface. Open the Password interface: A. right clicks anywhere to open the sub-menu, and select the main menu. B. Select the basic setting in the interface。 C. Select the password to enter the user management interface. Change the device serial number and password： A. Click serial number and key into 6 numeral numbers (by mouse).
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 NAME: input the new name through mouse or remote control. POSITION: locate the channel name in live window; there are TOPLEFT, BOTTOMLEFT, TOPRIGHT, BOTTOMRIGHT and OFF. Select OFF, the name will not be shown on the window. COLOR: adjusting the chrome, brightness, contrast and saturation. LIVE: there are ON/OFF option to display/hide the playback time and date. PREVIEW TIME: there are ON/OFF options to display/hide the live time and date.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 I/O ALARM: show each channel alarm status, that is, when an alarm triggered, it will activate the corresponding channel to start alarm recording. NO: indicate alarm is Normal Open; it will be ON when have alarm NC: indicate alarm is Normal Close; it will be OFF when there is a alarm HDD LOSS: if ON, means it will trigger alarm if there is no HDD, and it will display【H】on the bottom of each channel in the live window.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 EMAIL: to select ON to make the email alarm function. SSL: one protocol of email, in SSL area, select “ON”. SMTP port: input the email provider SMTP port. SMTP server: input the email provider SMTP server address. SEND EMAIL: input the email sending account. SEND PW: input the password of above email. RECV EMAIL: input the receiving email account.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 EMAIL: To set the email sending function when the motion detection area is active. Buzzer: To set the buzzer ON or OFF. Notice: Buzzer could be set disable in alarm setup menu. 2.2.3.5.4 MOBILE It supports smart mobile surveillance, to set the mobile phone network and mobile port. Mobile Network: there are 2.5G、2.75G、3G options. As usual, we suggest 3G. Mobile Port: input the number you want to set for mobile phone port.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 AUTO MAINTAIN: if set in ON, the system will maintain the system very DAY, WEEK, and MONTH. SYSTEM UPDATE: it’s to update the system through USB driver. DEFAULT SETTING: to set the system in default, and all the data and setting will be deleted. RESTART: to restart the system. PARAMETER IMPORT: to import the DVR system setting parameter through USB. PARAMETER EXPORT: to export the DVR system setting parameter through USB.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Network setup: There are DHCP, PPPOE and STATIC three network connection type. The network setting steps is as following, 1. Choose Network type: A. DHCP If select the DHCP, before setup, please make sure the DVR is connected to router server. While choose DHCP, then DVR will get the IP address automatically through router server, and the DVR will restart. Make sure the UPNP is set in ON status.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 C. STATIC While select STATIC, and then input the IP address, subnet mask, gateway and DNS address. 2. Open the ports in router server. There’re few ports need to open in router server, the web port, media port, and mobile phone port. The default port is as follows, Media port: 9000 Web port: 80 Mobile phone port: 100 Note: A. If only remote access in LAN, the web port is necessary. B.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 C. STATIC After the system is restart, login the router server to see the router server running status, there’s a IP address for router server, then copy this IP address and input IE browser to remote access. 5. DNS This is the server of DNS, as usual, you could ignore this detail, the system will generate if you choose DHCP or PPPoE. If you choose STATIC, the DNS is the same with your computer. 6.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 B. Open web and media ports in router server, and enable the DMZ server function as well. And confirm to access successfully in WAN by public IP address of router server. C. After confirm it could be accessed by LAN and WAN, then set the DDNS in ON. There’re 3322, DYNDNS, perfecteyes, and JSJDVR.COM. D. Select JSJDVR.COM provider and input the sub domain name you want (Arabic number or Alphabet up to Max.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 At last, please do make sure the DVR is accessed by public IP address before to bind the dynamic domain of DVR. Only in this case, the sub domain could be registered to server. The dynamic domain servers of JSJDVR.COM support 15,000pcs DVR online simultaneously. 2.3 Touch-screen user manual(F8504FP/F8508F/F8504CP/F8508C) In order to use the DVR with touch-screen better, please read the manual carefully before using it.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 click revise touch-screen and login Click the cross center by hand or touch-pen. After clicking the first cross, it will appear the second in the middle. Click it again and it will appear the third on the right. Click it and it will exit automatically Click exit. You can use the touch-screen freely now. Note: the first time you use the touch-screen, it may be imprecise. Click by mouse and login the page to revise touch-screen.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Chapter 3 IE Remote Access 3.1 Features The system itself has the IE based software that it can allow you to remote control the system via WAN or Internet. So far, the DVR only support the browser which is developing on the base of Windows IE. To install software via the system based IE to make you remote access from internet conveniently. DVR supports C/S, B/S construction, WAN and LAN, as well as IP and domain name accessing.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 3.3 IE Browser Interface The IE Browser interface will be displayed after logging. ① Function Module: There is LIVE, PLAYBACK and SETUP. ② Channel Name: Channel number or channel name is displayed at the top left corner. ③ Date and Time: It is shown the date and time in each channel. ④ Main Screen: It is show the live window. ⑤ PTZ Control: It controls the PTZ camera.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 3.3.1 LIVE The live window is realized with real time preview mode (multi-scene) under default setting. A. Click the LIVE button in the main screen. B. Click display icon, choose single, four or multi-channel to check main screen. Meanwhile, double click left key to choose a channel to check in single mode. C. Click D. Click to check or conceal all channel windows. to start/stop to record and save the files to PC.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 C. Click +/- to control zoom, focus and iris. D. Exit presetting. E. Click setting, transferring and clear to control presetting further. 3.3.1.4 Snap Click to snap the pictures of current channel in main screen. The default picture is saved as BMP format and default save path in:（C:\DVR\[ip_address]\...） 3.3.2 Playback Click PLAYBACK to enter the search and playback menu. Record playback menu: A.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The purple color process bar shows download status, the green color progress bar shows playback process. You can click or move green signal (green to orange) to play fast forward or fast back. Pause/Play Stop Fast forward Slow play To next frame and pause Search Search the system video recording via the calendar and menu. A. Click or to change the Month. The date which has record file will be boldfaced. B.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Remote Backup Backup the record files and save the files to the PC. Remote backup file: A. Click PLAYBACK in the top main screen. B. Choose the date in the calendar, and then click REFRESH. C. Double click one recording in file list to play. D. Click BACKUP to C: /DVR/[ip_address]/Backup Note: A. When you playback a record file, meanwhile this record is also backup to your PC. B. Play the professional player to backup the record files. 3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 to enter record setting interface, you could set the DVR record parameter in remote access, which is the same as in GUI of DVR. The detail please references the Record in Chapter 2. 3.3.3.2 Alarm Click to enter the alarm setting interface; you could set the DVR alarm parameter in remote access, which is the same as in GUI of DVR. The detail please references the alarm in Chapter 2.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 3.3.3.3 PTZ Click to enter the PTZ setting interface; you could set the DVR PTZ parameter in remote access, which is the same as in GUI of DVR. The detail please references the PTZ in Chapter 2. 3.3.3.4 Network Click to enter network setting interface, you could set the DVR network parameter in remote access, which is the same as in GUI of DVR. The detail please references the network in Chapter 2. 3.3.3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Click to enter system setting interface, you could set the DVR system parameter in remote access, which is the same as in GUI of DVR. The detail please references the system in Chapter 2. BANDWIDTH: Select the amount of bandwidth in 128k, 192k, 256k, 384k, 512k and1024k which is your broadband width, this bandwidth depends on the place, normally around 256 or 384 kbps. SAVE PATH: Snap pictures and recording video save path. 3.3.3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4 VCA software operation manual (A8504FP/A8504CP/A8508F/A8508C) 4.1. Installation Attention: A. The IP address which is marked in VCA module is the device control address. If the gateway is different, please amend the device IP address or change net mask of TCP/IP property in computer of network to 255.255.0.0. B. The device ID is “root”, and with password of “pass”. C. There’re two software in CD, “MSXML4.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Click FINISH to finish the installation 4.1.2 Amend the IE browser security option Click the OPTION in IE browser, select PROPERTY and click PRIVATE to set. Click off the “Stop pop-up window”.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.2. Login 4.2.1 Login the VCA Run the IE browser and input the IP address of VCA which could be found at the bottom of product or run the “admintools” to search the device and identify the IP address.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Click Install After install the ActiveX and refresh the IE browser, the interface will be shown. Stream could be selected PTZ control 4.2.2 Live window OSD configuration Click right button of mouse to enter the property menu, Video: to set the information to show in live window, which could set to show the information such as codec, frame type, dts, bit rate, fps, etc.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Snap and Record: to snap the image and record. Event: to show the information of event, alarm and USB/SD status.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 VCA: to show the VCA tracking information. 4.2.3 PTZ Control PTZ control platform Click to set the PTZ Click to show preset position 4.3. Setup Click setup to enter the setup interface.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Input the account and password (default account is “root”, and password is “pass”). 4.3.1 Basic Configuration There’re User, WEB server and Date & Time setting.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.1.1 User To add, modify, cancel user information in this menu. 4.3.1.2 WEB Server To set the WEB login server and port. HTTPS protocol HTTP protocol 4.3.1.3 Date & Time To set the device date and time. Please pay attention that the date and time must be the same with comuter, and DVR device.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Set Date and Time Select time zone 4.3.2 Video & Audio To set the video standard and audio decode. 4.3.2.1 Video Input To set the video standard system and image property.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Select the video standard, must be the same with DVR and camera 4.3.2.2 Built-in Text To set the content, date and time. Support dual video streaming Text position 4.3.2.3 Codec To set the codec and resolution.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Select the stream Video codec Resolution Variable change Bitrate to Constant Bitrate Three compression, such as MJPEG, MPEG4, H.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Support multiple resolution 4.3.2.4 Snap To snap the image of preview. Image format Image resolution Customize image size 4.3.3 Event Configuration To set the alarm input/output, VCA, motion detection, etc.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.3.1 DI: To trigger the setting when there’s alarm input. Alarm input and alarm output To set the posting notification message 4.3.3.2 DO: To set the alarm output when the alarm is triggered.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.3.3 Video: When there’s video loss, the alarm will be triggered. To set the posting notification message when there’s video loss 4.3.3.4 Motion Detection: To set the motion detection in the area to triggered the alarm.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 To set the area of alarm when motion detection is triggered. 4.3.3.5 VCA: To set the VCA output 4.3.3.6 Network: To set the alarm when the IP address is changed.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 To set the triggered when IP address is changed 4.3.3.7 Health: To set the device temperature, DSPload. 4.3.4 System Options To set the network transmission protocol.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.4.1 TCP/IP: To set the TCP/IP protocol and IP address of device. Set the IP address via DHCP Input the IP address by manual 4.3.4.2 NAT: To set the public IP address in order for remote access from outside internet.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 To set the DNS for remote access from outside internet 4.3.4.3 NTP: To set the NTP server. Synchronize the device and server Set the local device 4.3.4.4 UPnP: ：To set the PnP protocol. as SNTP server 4.3.4.5 USB/SD Storage: To set the camera USB/SD card save path.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Show the device Device information Format the device 4.3.4.6 USB Wireless LAN: To set the USB wireless transmission status. Show the device in LAN through wireless Input the password to wireless 4.3.4.7 RTSP/RTP: To set the video streaming transmission and protocol.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Set in ENABLE Set in ENABLE to see the live video Multiple cast or Unit cast Need to enable this option when there’s second stream 4.3.4.8 mDNS: To set the mDNS option.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Multiple cast information 4.3.4.9 SMTP: To set the email SMTP server in order to send the email when alarm is triggered. Sender information SMTP Server Input the account and password 4.3.4.10 AVI Record: To set the camera USB/SD record option.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Record bit rate Set the record processing rule Record resolution 4.3.4.11 LED: To set the LED shining rule in front panel. Set the LED color for different event Set the LED color for different video record 4.3.4.12 DDNS: To set the IP address of device to match the DDNS server.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 ENABLE DDNS DDNS server information DDNS server account and password 4.3.5 IO Configuration: To set the alarm input, output and configuration of ports. 4.3.5.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.5.2 UART PTZ protocol address and PTZ baud rate Stop bit position 4.3.6 Maintenance: To maintain the device and see the log information. 4.3.6.1 Upgrade Set the device to be upgraded through network Enable to save the log automatically 4.3.6.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.6.3 Website To set the VCA result to show in website Enable to show the VCA result in the website 4.3.7 Motion Detection: To set the camera motion detection in the area. Area 1 Area 2 4.3.8 About 4.3.8.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.3.8.2 License 4.4. VCA setting 4.4.1 Setup before VCA Attention: Before set the VCA function, please make sure the Video/Audio setting is as bellows。 Video/Audio Codec Select the second stream Click off “Enable” 4.4.1.1 Switching VCA On and Off By default, VCA is disabled. In order to enable VCA it must be activated. Select the VCA menu and then the Enable/Disable sub menu.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.1.4 Enabling Metadata Streaming In order to visualize the VCA output, metadata streaming must be enabled for RTP. Select System Options and then the RTSP/RTP sub menu: 4.4.1.5 License Once an activation code has been received from your hardware supplier, it's simply a case of entering the code on the appropriate web page.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Enter the activation code and click "Apply". If the activation code is valid, the activated features will be displayed in the "Installed Licenses" box. 4.4.2 Configuration of Zones and Rules In order to create some useful output, it is necessary to configure detection zones and detection rules. The detection zones and rules are configured by selecting VCA and then the Zones and Rules sub menu: 4.4.2.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.2 Properties Inspector The properties inspector allows the user to assign detection rules to detection zones and detection lines.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.3.4 Display Object Height Check this option to display the object height. This option is only available when the camera has been calibrated.Display Object Speed Check this option to display the object speed. This option is only available when the cam era has been calibrated. 4.4.2.3.5 Display Object Area Check this option to display the object area. This option is only available when the camera has been calibrated. 4.4.2.3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.4.3 Adding and Removing Nodes Zones and lines can be tailored to any scenario by simply adding more nodes to define the shape required. To add a node, simply double click on the zone or line at the point where the new node should be added. Nodes can be deleted by right clicking on node and selecting Node…remove 4.4.2.4.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The properties inspector is context-sensitive to the zone selected. As different zones/lines are selected, so the properties inspector changes to reflect the rules currently configured on that zone. Defining a rule is a simple matter of checking the box next to the rule required. In all cases, the rules are configured with sensible default values. Of course, these can be customized to suit the detection scenario.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.6.2 Object Appear and Disappear Enable the object appears and disappear detection by checking the corresponding check boxes in the properties inspector and click apply. An object appears alarm is raised when an object appears inside a detection zone. Note that this is different from object entered detection since the object must be initially detected inside the zone without entering, e.g.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.6.4 Object Dwell Enable the object dwell rule on the selected zone by checking the Dwell box in the properties inspector and click apply. Objects that dwell inside a zone for longer than the defined amount of time will trigger the rule and raise an alarm. 4.4.2.6.5 Object Stopped Enable the object stopped rule on the selected zone by checking the Stopped box in the properties inspector and click apply.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.6.6Object Speed Enable the object speed rule on the selected zone by checking the Speed Filter box in the properties inspector. Adjust the lower and upper speed limits to suit the detection scenario. Objects that travel within the bounds of the configured speeds, through a zone or over a line trigger the rule and raise an alarm. Note that the camera must be calibrated for this function to be available. 4.4.2.6.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.6.8 Object Direction Enable the object direction rule on the selected zone by checking the Direction Filter box in the properties inspector. Adjust the direction and acceptance angle to suit the detection scenario. Objects that travel in the configured direction (within the limits of the acceptance angle) through a zone or over a line trigger the rule and raise an alarm.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Object 2 crosses the line within 5 seconds of Object 1. This triggers the Object Tailgating filter. 4.4.2.6.10 Abandoned Object VCAsys can be configured to generate an alert highlighting an abandoned object. Suspicious objects can be detected when carried into the scene and planted by a person as well as when dropped or thrown into the scene.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 after a moving object appears inside the zone. The abandoned object rule triggers the alarm after an object is dropped inside the zone and left for a defined time period. 4.4.2.6.11 Stationary Object Hold-on Time The stationary object hold-on time is the time which the tracker will keep tracking an object once it has been detected as stationary or abandoned.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.7.2 Enabling the Counting Line Enable the counting line filter on a detection line in the desired direction(s) by checking the appropriate box in the properties inspector. An event is generated every time an object crosses the line in the selected direction. If multiple objects cross the line together, multiple corresponding events are generated. The events generated by the counting line can be tied to counters in the normal manner.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Instead of the 3D calibration tool, the counting line has its own calibration setting. Two bars equidistant from the centre of the line represent the width of the expected object. This allows the counting line to reject noise and also count multiple objects. To calibrate the counting line: Select the counting line with the mouse. Check the "Width Calibration" box under the Counting Line rule in the property inspector.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 When the diagnostics metadata is enabled, the diagnostics will appear as black and white lines on either side of the counting line on the Zones and Rules page. Each line represents an object which was detected by the counting algorithm. The width of the line shows the width of the object detected by the line. The last 5 detections are displayed for each direction with the latest one appearing closest to the counting line.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The counter name can be changed by clicking in the Name box on the rules control. 4.4.2.8.2 Assigning Rules to counters Counters count triggers generated by rule violations. For example, if it is required to count the number of objects entering a zone, a zone must initially be configured to raise an alarm every time an object enters it.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.9 Camera Calibration Camera calibration is required in order for the VCA engine to classify objects into different object classes. Once the camera has been calibrated, the engine can infer real-world object properties such as speed, height and area and classify objects accordingly. 4.4.2.9.1 Calibration Page Elements The following describes the purpose of each element of the calibration page.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.9.6 Additional Mimics Additional mimics can be added to verify the calibration configuration. Select the Add Mimic option from the menu. 4.4.2.9.7 Grid Transparency By default the ground plane is displayed in transparent mode such that the video is clearer. The transparent grid can be toggled by selecting the corresponding menu option. 4.4.2.9.8 Virtual Ruler The calibration configuration control supports a virtual ruler.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.10 Calibrating a Camera Calibrating a camera is necessary in order to estimate object parameters such as height, area, speed and classification. If you know the height, tilt angle and vertical field of view corresponding to your installation, you can simply type the parameters in the appropriate boxes and apply the changes.
XX Series Network DVR User Manual……………………………………………………………………….V1.0 Once the changes have been applied, the Calibration Status reflects whether the operation was successful, and if so, in which mode the camera is calibrated. Step 3: Verify the setup Once you are happy that the scene is correctly calibrated, verify the settings by dragging the mimics around and comparing them to other people or people-sized objects in the scene.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.2.12 Vertical Field of View The vertical field of view is required when calibrating a camera. If you know the vertical field of view of the camera it can be entered directly.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.3 Object Classification VCAsys can perform object classification once the camera has been calibrated. The object classification is based on properties extracted from the object including object area and speed. VCAsys comes pre-loaded with the most common object classes, and in most cases these will not need to be modified. In some situations it might be desirable to change the classification parameters, or add new object classes.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The output of the tamper detection algorithm is displayed as red blocks on the image. The red area is where the algorithm has detected that the image has changed from its reference image. Once enough of the image has changed and remained so for a certain length of time, a tamper alarm is triggered. Note: In order to see the output of the tamper detection on the image, Tamper Debug metadata must be enabled on the VCA -> Advanced page.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.7 Configuration Select the object properties to display. The object text size can be changed according to the user's preferences. Objects can be displayed in either two-color or multi-color mode. In two-color mode, select the display colors for objects in alarm and objects not in alarm. In multi-color mode, the object colors are selected automatically by the system. 4.4.7.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The different text sizes available are illustrated below: 4.4.8 Stabilizer The video stabilizer utilizes advanced digital image stabilizing algorithms to minimise the effects of camera shake. The stabilizer is enabled and configured using the pages under the Stabilizer tab in the left menu.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 the stabilizer functionality has been enabled by providing a VCA Stabilizer license, the option to enable the stabilizer will appear in the Enable/Disable page. Enabling or disabling the stabilizer will cause a few seconds pause as the system is re-configured. 4.4.8.1 Stabilizer Configuration When the stabilizer is enabled an additional configuration page is available under the Stabilizer tab.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Fixed: A fixed size black border is present on all sides which blanks out the moving edges of the image. The size of the borders is equal to the maximum frame shift (see below). None: Old frames are not displayed. Regions of the output image for which there is no available data are filled with black 4. 4.8.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 To access the event configuration select the Event Configuration menu and then the VCA sub menu: The external event notification will be generated every time there is at least 1 VCA alarm active. 4.4.10 Load and Save VCA Settings It is possible to export the VCA settings from a device to an XML configuration file, and to re-load the settings back into the device at a later date.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.11 Advanced VCA Settings In most installations, the default VCA configuration will suffice. However, in some cases, better performance can be achieved with modified parameters. The Advanced VCA Settings page allows configuration of the advanced VCA parameters. 4.4.11.1 Alarm Holdoff Time The Alarm Holdoff Time defines the time between the successive re-triggering of an alarm generated by the same object triggering the same rule.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 To explain this concept, consider the following diagram where no Alarm Holdoff Time is configured: In this detection scenario, the person enters the zone 3 times. At each point an alarm is raised, resulting in a total of 3 alarms. With the Alarm Holdoff Time configured, it's possible to prevent re-triggering of the same rule for the same object within the configured time period.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 In essence, the Alarm Holdoff Time can be configured to prevent multiple alarms being generated because an object is loitering on the edge of a zone. Without Alarm Holdoff Time configured, this scenario would cause so-called "Alarm chatter". The default setting for Alarm Holdoff Time is 5 seconds. 4.4.11.2 Measurement Units Allows the measurements units to be switched between Metric and Imperial formats.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4.4.11.12 Tracking Options Minimum Tracked Object Size The Minimum Tracked Object Size defines the size of the smallest object that will be considered for tracking, in pixels. Normally there is no need to modify this value. Decreasing it will allow the engine to track smaller objects at the expense of noise immunity. 4.4.11.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 8508C/F8508C/A8508C front panel Type Control button Name Illuminations Direction key Direction key include: up【 】 、down【 】 、left【 】 、 right 【 four buttons, which can move cursor to setup and control PTZ.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 12 5.2 Fan Please check the fan function for diary maintained and change new one if the fan has some problems DVR HDD Installation Demonstration 5.2.1 HDD Installation Attention: To prevent any damage to DVR and HDD, it is better to ask professionals to install HDD. 1. Uninstall the DVR and then you will see one HDD plate as following. 2. Connect HDD line as follows 3.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 4. Cover the DVR and screw. Notice: Newly installed HDD should format before recording. Chapter 6 Device Part 6.1 Check Device part 1.Digital Video Recorder 1 SET： 2.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 3. Optional Part Chapter 7 FAQ 1. 2. 3. If your problem is not in below, call our hotline and we will resolve any issues or problems you may have.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 DVR 4. 5. 6. Please directly insert the video source into the display device, and check whether the video source and display device aspect of the problem.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 The connect is not correct The PTZ setting of DVR is not correct The PTZ decoder does not match with the DVR agreement When connecting multi decoder, 120 Ω electric resistances should add at the end of PTZ decoder AB line, or else PTZ will not be stable. The distance is too far 11. Question：Why the “Stop recording” by the right mouse button does not work, how to stop recording? 12. 13. 14. 15. 16. 17.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 display normal; use ping xxx.xxx.xxx.xxx (DVR IP) to check if the internet is well linked Recommended Windows XP or Vista operating system, using IE6.0 browser or IE7.0 browser ActiveX control is been blocked. Please manual install ActiveX control. Please install DX8.1 and upgrade your video card driver 18.
85XX Series Network DVR User Manual……………………………………………………………………….V1.0 Guarantee Guarantee Item 1. 3months upon date of purchase: if there is function problem, we should offer the same item subject to goods and packing maintain perfect 2. 1 year upon date of purchase: we will guarantee to keep the goods in repair.(not including fittings) 3. Guarantee service is subject to normally using 4.
85XX Series Network DVR User Manual……………………………………………………………………….V1.
