V1362DIR / V1363TIR / V1382TIR Vandal Dome Camera User Manual ABOUT MANUAL Before installing and using the camera, era, please pleasse read this th his manua manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages. ̰GDo not put objects into the unit. ̰GGGGKeep metal objects and flammable substances from entering the camera. It can cause fire, short- circuits, or other damages. ̰GGGBe careful when handling the unit. ̰ To prevent damages, do not drop the camera or subject it to shock or vibration. ̰ Do not install near electric or magnetic fields.
TROUBSHOOTING Before sending your camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. ̰ No Video Is the coaxial cable attached securely? Is there adequate illumination? ̰ Out-of-Focus Video Is the lens in focus? Is the lens dirty? (commercially available) and a soft cloth or lens cleaning paper. WARNING : TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
DIMENSIONS IN MILLIMETERS* 103.1 109.6 41.3 91.0 85.0 6.5 ø145 ø5.0 85.0 91.0 117.0 125.0 ø4.
INSTALLATION* F G 1. Loosen the Fixing Screw (D), using a screw driver. 2. Separate the Upper Case (A) and the Base (E). 3. Detach the Gimbal (C) from the Base (E). E 4. Cut a hole in the ceiling for routing the cables. C 5. Place the Base (E) horizontally against the ceiling and drill the screw holes at the two marked positions. 6. Pass the Power Cable (F) and Video Cable (G) from the camera unit through the cable hole in the ceiling. B 7.
CONNECTION* DC12V DC12V / AC24V 300.0 CAUTION : CHECK FOR POLARITY WHEN USING A DC12V POWER SUPPLY.
CAMERA SETTINGS* ̰GLENS ADJUSTMENT 1. Focus Lever 2. Zoom Lever 1. Set the zoom level to the desired position by moving the Zoom Lever. 2. Set the focus, using the Focus Lever.
CAMERA SETTING FOR SIDE OSD CONTROL BOARD* V1362DIR, V1363TIR, V1382TIR FUNCTIONAL OF CONTROL BOARD [1] SW Functional control of O.S.
REMOTE CONTROL* ̰GREMOTE CONTROL Instructions Menu Access and Control Zoom Function Control Key Button 1. Set the Camera iD in the OSD menu. The default setting is 001. NOTE : you must reset the power for the new settings to apply. Once you reset the power, the camera will recognize the new Camera ID. 2. If you press the KEY Button, the camera display will turn into the standby image. NOTE : The LED ID Buttons Motion Alarm ON / OFF 3.
MODULE OSD MENU* (V1362DIR) EXPOSURE COLOR BRIGHTNESS SHUTTER BLC AGC FUNCTION DAY&NIGHT WB MODE MOTION MIRROR SHARPNESS GAMMA SLC HME DRC SYNC PRIVACY ALARM SETUP SYNC D&N MODE MASK 1 MASK 2 MASK 3 MASK 4 COLOR SET EXIT CAMERA ID TITLE EDIT TITLE RESET TITLE POSITION DPC SET LANGUAGE PC CONT.
OSD MENU* (V1362DIR) EXPOSURE BRIGHTNESS MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31) SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000 OFF / ON BLC (Back Light Compensation) OFF / 12dB ~ 36dB AGC (Auto Gain Control) BLC AGC EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET COLOR WB MODE AWC / ATW / MANUAL / PUSHLOCK (AWC is recommended.
FUNCTION MIRROR OFF/ MIRROR SHARPNESS 0 ~ 49 GAMMA USER / 0.45 / 0.6 / 1.
PRIVACY MASK 1 OFF / ON MASK 2 OFF / ON MASK 3 OFF / ON MASK 4 OFF / ON COLOR SET EXIT JUMP BLACK / GRAY / COLOR 1~ 6 EXIT / SAVE&EXIT / FACTORY SET SYNC SYNC MODE INTERNAL / AUTO V-PHASE 0 ~ 199 EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET SETUP CAMERA ID 0 ~ 255 TITLE EDIT TITLE RESET TITLE POS. DPC LANGUAGE OFF / AUTO DPC ( Dead Pixel Cancellation) English / Chinese PC CONT.
MODULE OSD MENU* (V1363TIR) EXPOSURE COLOR FUNCTION DAY&NIGHT WB MODE R-Y GAIN B-Y GAIN BRIGHTNESS SHUTTER BLC / HME AGC STARLIGHT NIGHT-UP MOTION MIRROR SHARPNESS GAMMA FREEZE NEGATIVE D-ZOOM 3D DNR DRC SYNC PRIVACY MOTION SETUP SYNC D&N MODE C_SUP A_SUP PRIVACY EXIT TITLE EDIT PC CONTROL LANGUAGE MONITOR OSD COLOR OMNI LENS EXIT SAVE & EXIT FACTORY RESET 14
OSD MENU* (V1363TIR) EXPOSURE BRIGHTNESS SHUTTER BLC/HME AGC STARLIGHT NIGHT-UP EXIT JUMP 0 ~ 100 1/60, FLK, 1/250 ~ 1/100000 OFF / BLC / HME HIGH / MIDDLE / LOW / OFF AGC (Auto Gain Control) AUTO (x2 ~ x256) / OFF NORMAL / HIGH EXIT / SAVE & EXIT / FACTORY SET COLOR WB MODE R-Y GAIN B-Y GAIN EXIT JUMP AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR 0 ~ 100 0 ~ 100 EXIT / SAVE & EXIT / FACTORY SET DAY & NIGHT Day & Night Mode C-SUP A-SUP EXIT JUMP 15 AUTO: READ TIME(3~63) / S-LEVEL(0~100) / E-LE
FUNCTION MIRROR OFF / MIRROR / V-FLIP / ROTATE SHARPNESS 0 ~ 31 GAMMA 0.05 ~ 1.00 / USER FREEZE OFF / ON NEGATIVE OFF / ON D-ZOOM OFF / ON (x1.
SYNC SYNC EXIT JUMP INTERNAL / LINE EXIT / SAVE & EXIT / FACTORY SET SETUP TITLE EDIT PC CONTROL (RS485 Control) LANGUAGE MONITOR OSD COLOR OFF / ON CAM ID / ID DISPLAY (OFF/ON) / BAUDRATE (2400 / 4800 / 9600) The protocol is PELCO-D. ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL CRT / LCD Select LCD only if the camera is directly connected to the LCD monitor.
MODULE OSD MENU* EXPOSURE (V1382TIR) COLOR BRIGHTNESS SHUTTER BLC AGC MAX_DR STARLIGHT FUNCTION DAY&NIGHT WB MODE R-Y GAIN B-Y GAIN MOTION MIRROR SHARPNESS GAMMA FREEZE NEGATIVE 3D DNR D-ZOOM SLC HME DIS SYNC PRIVACY MOTION SETUP SYNC D&N MODE C_SUP A_SUP MASK 1 MASK 2 MASK 3 MASK 4 MASK 5 MASK 6 EXIT CAMERA ID TITLE DPC MONITOR LANGUAGE BAUDRATE OMNI LENS EXIT SAVE & EXIT FACTORY RESET 18
OSD MENU* (V1382TIR) EXPOSURE BRIGHTNESS SHUTTER BLC AGC MAX_DR STARLIGHT EXIT JUMP 0 ~ 99 1/60, 1/100FLC, 1/120~1/100000 OFF / ON BLC (Back Light Compensation) HIGH / MIDDLE / LOW / OFF AGC (Auto Gain Control) OFF / ON (0~20) (Electronic Wide Dynamic Range) AUTO (x2 ~ x256) / OFF (x32 is recommended for low light application.) EXIT / SAVE & EXIT / FACTORY SET COLOR WB MODE R-Y GAIN B-Y GAIN EXIT JUMP AWC / ATW / MANUAL / PUSHLOCK (AWC is recommended.
FUNCTION MIRROR OFF/MIRROR/V-FLIP/ROTATE SHARPNESS 0 ~ 49 GAMMA 0.05 ~ 1.00 / USER FREEZE OFF / ON NEGATIVE OFF/ ON OFF / LOW / MIDDLE / HIGH 3D DNR (3D Digital Noise Reduction) OFF / ON(x1.0 ~ x3.
PRIVACY PRIVACY EXIT JUMP MASK 1 OFF / ON MASK 2 OFF / ON MASK 3 OFF / ON MASK 4 OFF / ON MASK 5 OFF / ON MASK 6 OFF / ON EXIT / SAVE&EXIT / FACTORY SET SYNC SYNC MODE V-PHASE EXIT JUMP INTERNAL / AUTO 0 ~ 199 EXIT / SAVE & EXIT / FACTORY SET SETUP CAMERA ID TITLE DPC 0 ~ 254 OFF / ON OFF / AUTO DPC (Dead Pixels Cancellation) MONITOR CRT / LCD (Select LCD only if the camera is directly connected to LCD monitor.
SPECIFICATIONS* Model V1362DIR Camera TYPE Image Color/BW Vandal Dome Camera Mount Surface Device Super HAD II CCD Size 1/3" Pixels-Total 811(H) X 508(V) 768(H) X 494(V) Scanning System 525 line, 2:1 Interlace Horizontal Frequency Internal Mode 15,734Hz Vertical Frequency Internal Mode 59.94Hz Min. Scene Illumination IR-LED On 0.
SPECIFICATIONS* Model Camera TYPE Image V1363TIR Color/BW Vandal Dome Camera Mount Surface Device Super HAD II CCD Size 1/3" Pixels-Total 811(H) X 508(V) 768(H) X 494(V) Scanning System 525 line, 2:1 Interlace Horizontal Frequency Internal Mode 15.734Hz Horizontal Frequency Line-Lock Mode 15.750Hz Vertical Frequency Internal Mode 59.94Hz Vertical Frequency Line-Lock Mode 60Hz Min. Scene Illumination IR-LED On 0.
SPECIFICATIONS* Model V1382TIR Camera TYPE Image Color/BW Vandal Dome Camera Mount Surface Device Super HAD II CCD Size 1/3" Pixels-Total 811(H) X 508(V) 768(H) X 494(V) Scanning System 525 line, 2:1 Interlace Horizontal Frequency Internal Mode 15,734Hz Vertical Frequency Internal Mode 59.94Hz Min. Scene Illumination IR-LED On 0.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warrantor”) warrants the Camera Series against defects in materials or workmanship as follows. LABOR : if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge.
LIMITS AND EXCLUSIONS* There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages, including without limitation or damage to recording media, resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the are limited to the applicable warranty period set forth above.
5436 W Crenshaw St. Tampa, FL 33634 Tel: 866-446-3595 / 813-888-9555 Fax: 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
