ANALOG HIGH DEFINITION Mini Outdoor Dome Camera DWC-V7753TIR DWC-V7753 ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
Table of Contents TABLE OF CONTENTS Introduction Features Parts and Descriptions Dimensions Installation Inside the Box Installation Instructions Installation using Mount Bolt & Nut Connecting to Monitors Control Board Adjusting the Camera Angle Module OSD Menu 4 5 6 7 8 9 10 11 12 13-28 Troubleshooting 29 Warranty Information 30-31 Specifications 32-33 3
FEATURES* Analog High Definition (AHD) HD over Coax Technology STAR-LIGHT™ Super Low Light Technology 1/2.7” CMOS Sensor 1080P Resolution at 30fps Fixed Lens 3.6mm Smart IR™ with Intelligent Camera Sync.
PARTS & DESCRIPTION* Dome Cover CAUTION Lens Gimbal Bottom Case 2nd Video Output BNC Cable OSD Joystick Set Screw 5
DIMENSIONS IN MILLIMETERS (IN)* 32.5 60.7 105.
INSIDE THE BOX* Included with Bullet Camera: 1 2 3 User Manual Mounting Template 2 Machine Screws and 2 Dry Wall Anchors 4 5 Mounting Bolt & Nut L-Wrench ANALOG HIGH DEFINITION Mini Outdoor Dome Camera DWC-V7753WTIR ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
INSTALLATION INSTRUCTIONS* Template Sheet 1. Detach the camera’s cover dome from the camera’s module by unscrewing the three cover dome screws using the L-Wrench. 2. Use the camera or mounting template to mark and drill the necessary holes in the wall or ceiling. 3. Pull wires through and make connections. 4. Using three (3) included screws, mount and secure the camera to the wall or ceiling. 5. Secure the camera’s cover dome onto the camera base and remove the protecting film to complete the installation.
INSTALLATION USING MOUNT BOLT & NUT* 1. Detach the camera’s cover dome from the camera’s module by unscrewing the three cover dome screws. 2. Using the camera or mounting template, mark and drill the necessary holes in the wall or ceiling. 3. Secure the two long mounting screws to the camera’s base. 4. Pull wires through and make connections. 5. Mount the camera to the mounting surface using the 2 mounting nuts. 6. Secure the camera’s cover dome onto the camera base to complete the installation.
CONNECTING TO MONITORS* Use the diagram below to connect to a Monitor or CRT Monitor properly. 12VDC CCTV Monitor Second Video Output Monitor Power Connection - 12VDC Voltage. All cameras are equipped with a second video output for on-site configuration.
CONTROL BOARD* 1 2 3 Remove the camera’s dome cover to access the camera module and OSD joystick. Use the Joystick to control the camera’s OSD options. The camera has a manual IR switch, located under the camera’s lens. You can use this switch to manually turn the IR LED board on or off according to the installation needs.
ADJUSTING THE CAMERA ANGLE* 1 Rotation 360º 2 3 12 Tilting 70º IR LED Panning 360º
MODULE OSD MENU* LENS P-IRIS MANUAL / AUTO MANUAL DC INDOOR / OUTDOOR EXPOSURE SHUTTER AUTO / 1/30~1/50000 / X2~X30 AGC STAR-LIGHT 0 ~ 15 OFF / AUTO X2 ~ X30 BACKLIGHT OFF WHITE BALANCE BLC ATW PUSH HME MANUAL LEVEL / AREA / DEFAULT / RETURN AREA / DISPLAY / BLACK MASK / LEVEL / MODE / DEFAULT / RETURN BLUE(0~100) / RED(0~100) AWB BRIGHTNESS 1 ~ 100 DRC OFF / AUTO / ON (0 ~ 8) DEFOG OFF / AUTO RETURN DAY & NIGHT NR (Noise Reduction) SPECIAL ADJUST AUTO AGC / CDS 2DNR CAM TITLE C
LENS MANUAL P-IRIS Manual mode supports the fixed board lens or the manual iris lens. If the camera includes a P-Iris lens, you can select this option to adjust the lens and iris settings. If P-Iris is selected, adjust the following: MODE: Select from AUTO or MANUAL. If AUTO is selected, the camera’s iris and lens will be adjusted automatically. LIMIT: If MANUAL is selected, the camera’s iris can be adjusted manually using the LIMIT value.
EXPOSURE SHUTTER Set the camera’s shutter speed from the available options (AUTO/1/30~1/50000/x2~x30/FLK) If Iris is set to AUTO in the lens menu, the camera’s shutter will be set automatically and the values in this menu will not be adjustable. If Iris is set to AUTO in the lens menu, the camera’s shutter speed will be deactivated. AGC AUTO GAIN CONTROL 0~15 AGC enhances the picture brightness in low light conditions.
EXPOSURE (CONT.) DRC DYNAMIC RANGE COMPRESSOR DRC enables dark areas in images to become more visible without overexposing the bright areas to create one perfect image. Select from: OFF / ON / AUTO. If ON is selected, adjust the DRC value from 0 ~ 8. NOTE: If DEFOG is enabled, DRC settings are set automatically and will not be available for adjustment. DEFOG 16 Allows the camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image.
BACKLIGHT BLC BACK LIGHT COMPENSATION If BLC is selected, adjust the size and position of the mask: - Level: Set the BLC levels LOW / MIDDLE / HIGH - AREA: Use the joystick controller on the camera’s board to adjust the zone’s position. Press the enter key and use the joystick controller to adjust the zone’s size. - DEFAULT: Return the BLC settings to their original default values. HME HIGHLIGHT MASKING EXPOSURE HME allows objects to appear clearly on the screen by masking extremely bright areas.
WHITE BALANCE ATW Auto Tracking White Balance Control mode compensates for color temperature changes between 2400Ko and 11000Ko. PUSH Push fixes the white balance based on the current lighting automatically. To use this function, press the ENTER key for five (5) seconds. MANUAL Control the white balance manually by changing RED and BLUE. RED: Adjusts the low color temperature in the image between 0 ~ 100. The default value is 42. BLUE: Adjusts the low color temperature in the image between 0 ~ 100.
DAY & NIGHT AUTO / models). COLOR / B&W/ EXT Day/ Night switch is based on the CDS levels (IR models) or AGC levels (non-IR The camera always stays in day/color mode. The camera always stays in night/B&W mode. The camera’s Day & Night settings are set according to an external IR LED board. AUTO For cameras with no IR LED Built-in: - D -> N Threshold (AGC): Set when the camera switches from day to night mode by the AGC value.
DAY & NIGHT (CONT.) COLOR If COLOR mode is selected, the camera’s display will always appear in color, regardless of the lighting condition. B/W - BURST: Select to enable or disable color burst when the camera switches from color to B/W. - IR SMART (0~15): Enable Smart IR and set the level. Higher values will make Smart IR stronger. - AREA: Set the Smart IR’s zone. Use the joystick controller on the camera’s board to adjust the zone’s position.
NR Smart DNR 3D DIGITAL NOISE REDUCTION 3D-DNR reduces the noise on the screen in low light conditions and allows for clearer images, even at night. 2DNR 3DNR Set the Digital Noise Reduction values for general illumination. Select from LOW / MIDDLE / HIGH. If the 2DNR settings are set to HIGH, image sharpness may be affected. Set the Digital Noise Reduction values for very low light situations. Select from LOW / MIDDLE / HIGH.
SPECIAL CAM. TITLE Add a name to the camera. Set the title by using the OSD joystick. D-EFFECT FREEZE MIRROR NEG. IMAGE Freeze image from the camera at the selected moment. Reflects the camera: OFF / MIRROR / V-FLIP / ROTATE Display the camera’s view in negative colors. Mirror / Flip OFF Mirror ON Flip ON Mirror & Flip ON MOTION - SELECT: The camera supports up to 4 separate motion detection areas. Select which one to adjust.
SPECIAL (CONT.) MOTION - ALARM: VIEW TYPE: When motion is detected, select from the following display options: 1. OFF - do not display motion alarm 2. ALL - Show all motion zones when motion alarm is detected. 3. BLOCK - show the area where motion is detected as a solid block. 4. OUTLINE - Show the area where motion is detected as an outline only. OSD VIEW: If enabled, ALARM will appear on the screen when motion is detected. ALARM OUT: The camera supports 3.3V alarm output.
SPECIAL (CONT.) PRIVACY - SELECT: The camera supports up to 4 separate privacy zones. Select which one to adjust. - DISPLAY: There are three types of privacy masks you can apply. Select from MOSAIC, INV., or COLOR. - MOSAIC: The privacy mask will appear as a mosaic over the camera’s image. - INV.: The privacy mask will appear as a negative of the image behind it, reversing the colors and brightness. - COLOR: The privacy mask will appear as a block of color according to the settings in the COLOR menu.
SPECIAL (CONT.) LANGUAGE Select from the available options: English, Chinese 1, Chinese 2, German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Korean, Japanese, Arabic, or Hebrew. DEFECT - LIVE DPC: - AGC LEVEL: Set the AGC levels for the Live DPC. - LEVEL: Set the level of Live DPC based on the AGC levels. - BLACK DPC - POS / SIZE: Set the size and position for the DPC Zone. Use the joystick controller on the camera’s board to adjust the zone’s position.
SPECIAL (CONT.) DEFECT (CONT.) - WHITE DPC - POS / SIZE: Set the DPC Zone. Use the joystick’ controller on the camera’s board to adjust the zone’s position. Press the enter key and use the joystick controller to adjust the zone’s size. - START: Press START to begin the DPC test. The screen will get bright and compensate for the black defect. - DPC VIEW: Show the Defect pixels which have been compensated. - LEVEL: Set the range of DPC application. - AGC: Set the value level for AGC while DPC is on.
ADJUST SHARPNESS Set the sharpness of the image. The Sharpness values can be increased or lowered according to the AGC levels in the camera’s view. If AUTO is selected, adjust the following values: - LEVEL: Set the sharpness level. The higher the number, the sharper the image will appear. - START AGC: Select the AGC value where the image’s sharp lines may start to appear smeared in low light. - END AGC: Select end AGC value for sharpness smearing in low light.
EXIT SAVE & END Save all changes made to the camera’s settings and exit the OSD menu. NOT SAVE Exit the OSD menu without saving any changes made to the camera’s settings. RESET The camera’s settings will be reset to their factory default values once you exit the OSD menu.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. FOR NO VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current. FOR OUT-OF-FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warranter”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows: LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warranter will repair or replace the unit with a new or refurbished product at its option at no charge.
LIMITS & EXCLUSIONS* There are no express warranties except as listed. The warranter will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* IMAGE Image Sensor Active Pixels Scanning System Frequency Signal Technology Synchronization Resolution Minimum Scene Illumination S/N Ratio Video Output LENS Focal Length Lens Type IR Distance OPERATIONAL Shutter Speed Backlight STAR-LIGHT 32 1/2.7” CMOS Sensor 1920(H) x 1080(V) Progressive scan 60Hz/50Hz 2.0 Megapixel AHD Internal 1920x1080 (1080p) F1.4 (30IRE): 1.0Lux [Color] F1.4 (30IRE): 0 Lux [B&W] 55dB AHD 1080p30fps/720p60fps/720p30fps 3.
SPECIFICATIONS* OPERATIONAL (CONT.) Digital Noise Reduction White Balance Day and Night Auto Gain Control Motion Detection Privacy Zones Sharpness Gamma UTC Off, Low, Middle, High Auto / Push / Manual / AWB Auto / Color / B/W / EXT 0 ~ 15 Yes 4 Privacy Zones 0 ~ 10 0.45 ~ 1.
MEMO* 34
MEMO* 35
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.