Vandal-Proof Dome Camera DWC-V4367WD DWC-V4367WTIR ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
TABLE OF CONTENTS Introduction Installation Features 4 Parts and Descriptions 5 Dimensions 6 Inside the Box 7 Mounting the Camera Connecting to Monitors Module OSD Menu Troubleshooting 8-13 14-15 Adjusting the Camera Lens 16 Adjusting the 3-Axis Gimbal 17 18-29 30 Warranty Information 31-32 Specifications 33-34 3
FEATURES* 1/3” Sony Super HAD CCD II 620 TV Lines (B&W), 600 TV Lines (Color) 3.
PART & DESCRIPTIONS* 1 2 Lens 2 Power Input Connector (Dual Voltage) 3 UTP 4 RS-485 5 Primary Video-BNC Output Connector 6 Camera Control Board 7 Bubble Dome Cover 8 Upper Case 9 Flush Mount Base 10 Surface Mount Base / Junction Box 11 Assembly Screws (#8 - 32 x 0.
DIMENSIONS IN MILLIMETERS (IN)* Flush Mount 137(5.39”) 101(3.98”) 17(0.67”) 28(1.1”) 98.8(3.89”) 121 (4.76”) 54(2.13”) Surface Mount 139(5.47”) 36(1.42”) 118.8 (4.68”) 29(1.41”) 53.8(2.12”) 6 121 (4.
INSIDE THE BOX* Included with Snapit Vandal Dome Camera 1 2 3 4 User Manual Mounting Template 4 Machine Screw and 4 Dry Wall Anchors TORX-T20 Wrench 5 6 7 8 L-Wrench TORX-T20 Bolt DC Plug Secondary Video-BNC Cable 7 8 7
SURFACE MOUNT INSTALLATION INSTRUCTIONS* Drill holes into the drywall and insert the drywall mounts into the holes. 4 Mount the surface mount base (junction box) to the wall. 8 Pull wires through and make connections. 5 If you need to keep the wiring within the camera housing, refer to the diagram below. 5 UTP RS48 DC 12V AC 24V Route wiring behind the inner posts (dark gray area). 3 RS48 2 UTP Use the camera’s mounting template or your camera to mark the holes as required.
5 Snap the camera module onto the base by aligning the red and black markings on the base and the camera module. 6 Secure the three (3) assembly screws. 7 Adjust the camera’s position by using the 3-Axis Gimbal. 8 Tighten the three locking screws in with the L-Wrench to secure the dome cover over the camera.
FLUSH MOUNT INSTALLATION INSTRUCTIONS* For a flush mount housing, detach the surface mount base, which is also known as the junction box, from the flush mount base. 1 Use the mounting template to mark the holes for the screws and a larger hole for the top extruded component of the flush mount base. 2 The three assembly screws (ST4X35) fixed to the flush mount base should be used to mount the camera to the surface of the wall or ceiling. ST4X35 3 Secure the three (3) assembly screws.
WALL MOUNT INSTALLATION INSTRUCTIONS* 1 Check to see all parts are in the box. 2 Insert the wires from the camera through the wall mount housing. 3 Use the mounting template to make pilot holes. Use the dry wall anchors and woods screws to attach the assembly. 4 Attach the camera’s surface mount base (junction box) to the wall mount. 5 Connect all cables and snap the camera module onto the base. 6 Adjust the camera and secure the dome cover over the camera module.
PENDANT MOUNT INSTALLATION INSTRUCTIONS* 1 Check to see all parts are in the box. 2 Attach the top shield to the pendant mount. 3 Run all necessary cables from the ceiling to the mount. 4 Use the mounting template to make pilot holes. Use the dry wall anchors and wood screws to attach the assembly to the wall. 5 Connect all cables and verify camera is operating properly. 6 Attach the camera to the ceiling mount and secure the dome cover properly.
CORNER MOUNT INSTALLATION INSTRUCTIONS* 1 Check to see all parts are in the box. 2 Attach the two compression fittings to the corner bracket. 3 Attach the wall mount bracket to the corner mount using the machine screws. 4 Mount the camera assembly to the corner of the wall, using wall mount anchors and machine screws.
CONNECTING TO MONITORS* Use the diagram below to connect to a Monitor or CRT Monitor properly. DC 12V / AC 24V CCTV Monitor IR NO IR 300.0mm(11.8”) Second Video Output Monitor Power Connection: 12VDC & 24VDC Dual Voltage (Auto Polarity Detection and Protection) All cameras are equipped with a second video output for on-site configuration.
UTP SYSTEM* Passive to Passive Monitor Passive UTP UTP Cable (Max.
ADJUSTING THE CAMERA LENS* Follow the instructions provided below to make any lens adjustments. Focus Zoom IR 1 2 3 4 ZOOM: TELE FOCUS: FAR - WIDE NEAR NO IR Loosen the zoom and focus handles by rotating them counter-clockwise. Adjust the field of view by moving the handle RIGHT(TELE) to zoom in or LEFT(WIDE) to zoom out. After the desired zoom position has been established, adjust the Focus the same way as described above.
ADJUSTING THE 3-AXIS GIMBAL* The Gimbal mechanism yields maximum rotation and placement as shown below.
MODULE OSD MENU* EXPOSURE COLOR LENS WB MODE BACKLIGHT OFF / BLC / HME / WDR AGC RED GAIN 0 ~ 255 BLUE GAIN 0 ~ 255 COLOR MODE NORMAL / COOL / WARM EXIT JUMP MANUAL / DC OFF / LOW / MID / HIGH / HIGHEST STARLIGHT OFF / x2 ~ x1024 3D DNR OFF / LOW / MID / HIGH / SMART EXIT JUMP AWC / ATW / MANUAL / PUSHLOCK DAY & NIGHT D&N MODE MIRROR / OFF 0 ~ 100 0 ~ 30 NIGHT C. NIGHT A.
EXPOSURE LENS Manual DC Manual mode supports the fixed board lens or the manual iris lens. DC mode supports the auto-iris varifocal lens. NOTE: Both MANUAL and DC mode have FOCUS TARGET. You can adjust the focus by finding the highest number on the FOCUS TARGET. See page 16 for focus information. ELC Levels and DC Levels are adjustable. The higher the number, the brighter the image. E. Shutter sets the shutter speed levels from 1/60 to 1/100000. *For LENS-MANUAL Mode, the default E.SHUTTER is AUTO.
EXPOSURE BACKLIGHT OFF BLC BACK LIGHT COMPENSATION MANUAL User can manually adjust the BLC level in five areas of the scene (TOP, BOTTOM, CENTER, LEFT, RIGHT). Increase the BLC levels to make the image brighter. SMART This is recommended. Camera will automatically detect and adjust the BLC zone. BLC levels to choose from include: LOWEST, LOW, MID, HIGH. HME HIGHLIGHT MASKING EXPOSURE HME masks highlights to allow objects to appear clearly on the screen. If ON is selected, HME levels are adjustable.
EXPOSURE AGC (AUTO GAIN CONTROL) OFF / LOW / MID / HIGH / HIGHEST STARLIGHT OFF / x2 ~ x1024 AGC enhances the picture brightness in low light conditions. A higher level AGC setting makes the images brighter; however, it could increase the amount of noise. Starlight mode automatically activates slow shutter function when the image is too dark. x4 is the default. We do not recommend you to increase the setting, for it causes the image to lag. Note: Starlight menu cannot be controlled if the E.
COLOR WB MODE Auto White Balance Control mode compensates for color temperature changes between 2000K and 18000K. ATW Auto Tracking White Balance Control mode compensates for color temperature changes between 2500K and 9500K. MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN (see below). PUSHLOCK Pushlock is to fix the white balance based on the current lighting. AWC RED GAIN 0 ~ 255 Adjusts the amount of red in the image.
DAY & NIGHT D&N MODE AUTO Camera switches between day and night automatically depending on light level. Camera will stay in color mode when there is enough light. Camera will switch to B&W at night or other low light environments. * COLOR B&W NIGHT C. 0 ~ 100 NIGHT A. If AUTO is selected, please define the following settings: *BURST: If ON is selected, the camera provides a color burst signal in night mode. If OFF, no color burst signal is provided.
FUNCTION MIRROR OFF MIRROR Flips the image horizontally. SHARPNESS 0 ~ 30 Sets the image sharpness. The higher the number, the sharper the image. GAMMA 0.45 / 0.60 / Select the desired gamma level. 0.45 is default setting. 1.0 / MANUAL SLC (SIDE LIGHT COMPENSATION) OFF / ON Increase the brightness on sides of the image. NIGHT-UP OFF / ON Adjusts sensitivity in low light conditions by set-up level. If ON is selected, the set-up level becomes higher, and the images become brighter.
MOTION The camera can detect the movement and display an alarm on the screen when movement is detected. AREA SET AREA 1 ~ 4 SENSITIV. 1 ~ 30 OFF / ON If ON, motion areas can be selected and moved accordingly. Select Areas 1-4 and adjust using controls for TOP, BOTTOM, LEFT, or RIGHT. Sensitivity level of the motion detection is adjustable. Motion Detection will be more sensitive at a higher number. SHOW INDI. OFF / ICON Set the Show Indicator to OFF, ICON, or TRACE.
PRIVACY You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking zones are available. MASK 1 ~ MASK 8 OFF / ON Select ON or OFF for each mask (MASK 1 through 8). If ON is selected you can set the area to be masked and the shape and color of the mask. *START POINT: Select the START POINT to adjust the size of the *privacy zone.
SETUP TITLE OFF / ON If ON is selected, you can display the camera title on the screen. *CLR: Clear the title. *POS: Position the title on the screen. DPC (DEAD PIXEL CANCELLATION) OFF DPC automatically removes defective pixels in real time. AUTO If AUTO is selected, you can define the following settings: *WHITE THR: Cancels the white defective pixels. *BLACK THR: Cancels the black defective pixels. *DPC LEVEL: Adjusts the sensitivity level of the dead pixel *cancellation.
SETUP MONITOR MODE 1 MODE 2 MODE 1 is the default. If the displayed image is not good enough, try MODE 2. LANGUAGE The camera supports the following languages: ENGLISH, CANTONESE, MANDARIN, JAPANESE, DEUTSCH, FRENCH, ITALIAN, RUSSIAN, SPANISH, AND DUTCH. OSD COLOR The following colors are available for the OSD menu: BLUE, GREEN, CYAN, RED, MAGENTA, YELLOW, PURPLE, and GRAY. COMMUNICATION OFF ON If ON is selected, you can define the following: *PROTOCOL: PELCO-D only.
EXIT EXIT SAVE & EXIT Save the current settings and exit the OSD menu. EXIT Exit the OSD menu without saving the changes.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. FOR NO VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current. FOR OUT-OF-FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows: LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge.
LIMITS AND EXCLUSIONS* There are no express warranties except as listed. The warrantor will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* VIDEO Image Sensor 1/3" Sony Super HAD CCD II Total Pixels 811 (H) x 508 (V), 411K Pixels Effective Pixels 768 (H) x 494 (V) Frequency 15.734KHz (H), 59.95Hz (V) Synchronization Internal or Line Lock Horizontal Resolution 620 TV Lines [B&W], 600 TV Lines [Color] Minimum Illumination F1.2 (30IRE): 0.14 Lux [Color] F1.2 (30IRE): 0.03 Lux [B&W]; 0.0 Lux [B&W] for IR Model S/N Ratio 50dB (AGC off) Video Output CVBS: 1.0Vp-p / 75 Ω LENS Focal Length 3.
OPERATIONAL Back Light OFF / BLC / HME / WDR White Balance AWC / ATW / MANUAL / PUSHLOCK Privacy Zones OFF / ON (8 Programmable Zones) Language ENGLISH / MANDARIN / CANTONESE / JAPANESE / GERMAN FRENCH / ITALIAN / RUSSIAN / SPANISH / DUTCH ENVIRONMENTAL Operating Temperature -29oC ~ 55oC (-20oF ~ 131oF) Operating Humidity Less than 90% (Non-Condensing) Storage Temperature -29oC ~ 70oC (-20oF ~ 158oF) IP Rating IP68 (Protects against dust and immersion beyond 3ft.
MEMO* 35
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
