Quick Start Guide

Quick Start Guide
DWC-PZ21M69T
WHAT’S IN THE BOX
Quick Manual &
Download Guide
1 Set
Screw & Plastic
Anchor – 4pcs
1 Set
Template Sheet 1 Set Tor x Wrench 1 Set
Moisture absorber -
2pcs & Absorber Guide
1 Set
Waterproof cap
& Gasket
1 Set
PoE Injector and
power cable
1 Set
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper camera usage.
Tel: [phone]
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Quick Start Guide
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
STEP 2 – POWERING THE CAMERA
1. Mounting surface must withstand three times the weight of the camera.
2. Do not let the cables get caught in improper places or the electric line cover to be damaged. This may cause a short or fire.
3. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.
4. For the installation process, remove the dome cover by loosening the screws on the dome. Use the wrench provided with the camera.
2. Your camera comes with a moisture absorber included in the package. This
absorber needs to be installed inside the camera, next to the lens, to prevent
moisture build-up on the camera’s dome that reduces image quality.
(
1
)
. Remove the moisture absorber from the packaging.
(
2
)
. Follow the diagram to place the absorber in the appropriate location.
3. The camera’s four individual sensors can be rotated and tilted to adjust the camera’s views. Max tilt and rotation:
- Rotation: 20º
- Tilt: 18º
4 . Assemble the dome cover over the camera body and detach the protecting film to complete the installation.
Connect the camera to the PoE injector included in the box. Connect the PoE injector to an adequate power source. See table
below for power source requirements. Refer to the user manual for more options to power up the camera.
Power Requirements Power Consumption
DC12V, PoE IEEE 802.3at PoE+ class 4
(High power PoE injector included)
DC12V Max 21.5W
PoE Max 23.4W
To reset the camera, press the reset button. Pressing the button for five (5) seconds will initiate a
camera-wide reset of all the settings, including network settings.
1. To use the camera’s water proof wiring:
(
1
)
. Install the LAN cable into (a).
(
2
)
. (b) will be assembled to (a) with a 1/4 turn.
(
3
)
. Thread (c) tightly to (b).
a
b
c
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
NOTE: When using the PoE+ injector, do not connect the PoE injector to the
PoE/PoE+ switch or PoE/PoE+ enabled port of PoE/PoE+ switch.
NOTE: When using the waterproof cap, crimp the RJ45 connector after
passing the cable through the waterproof cap.
Template Sheet
Reset Buon
3
2
7
6
5
4
3
2
2
1
Template Sheet
Reset Buon
Ethernet
cable
PoE
Injector
Ethernet Switch
power cable,
connected to
adequate
power source.
Please attach 2 card type
absorbers to attachment
points as the picture.