Quick Start Guide

Quick Start Guide
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
DWC-PVF5M1TIRC6 - 64GB Storage
DWC-PVF5M1TIRC1 - 128GB Storage
DWC-PVF5M1TIRC2 - 256GB Storage
Default Login Information
Username: admin Password: admin
Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch,
connect the camera using an Ethernet cable for both data and
power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power Requirements Power Consumption
DC12V, POE IEEE 802.3af
class 3 (Adapter not
Included)
LED On: 6.5W
LED O: 3.6W
POWER
NETWORK
Soft surface
installation
For soft installation
surfaces, use the
included metal
mount plate. Fix the
mount plate on the
mounting surface
using the included
screws. Then, press
the bottom case onto
the mount plate. The
three bezels on the
case will align and
snap lock onto the
plate.
Template
Sheet
a
b
c
1. Once all cables are connected, secure the camera to the mounting
surface using the included screws.
2. For soft installation surfaces, use the included metal mount plate. Fix
the mount plate on the mounting surface using the included screws.
Then, press the bottom case onto the mount plate. The three bezels
on the case will align and snap lock onto the plate.
3. To use the camera’s water proof wiring:
a. Install the LAN cable into .
b. will be assembled to with a 1/4 turn.
c. Thread tightly to .
STEP 3 – INSTALLING THE CAMERA
a
a
b
b
c
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line
cover to be damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock do not perform
any servicing other than that contained in the operating instructions
unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply
Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc,
525 mA min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with the
output evaluated as a Limited Power Source as defined in UL60950-1
or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined
in IEC TR 62102. As such, associated Ethernet wiring shall be limited
to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
STEP 1 – PREPARING TO MOUNT THE CAMERA
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
a
b
4. Re-attach the camera’s gasket ring and dome to the camera module
by aligning the screw holes.
5. The camera includes a sensor at the camera’s module. For the sensor
to function properly, the camera’s dome includes a special hole for
the sensor.
6. When assembling the camera together, please make sure the sensor
hole in the camera’s dome is positioned right on top of the sensor on
the camera’s module.
WHAT’S IN THE BOX
Quick setup
guide
1
Mounting bolts
and nuts –
2pcs
1 set
Metal mounting
plate
1
Screws and
plastic anchors
– 3pcs
1 set
Mounting
template for
bolt and nut
installation
1
Waterproof
cap
1 set
Mounting tem-
plate for metal
plate installation
1
Hex Allen
wrench
1
Attention: This document is intended to serve as a quick reference for the
initial setup. It is recommended that the user read the entire instruction manual
for complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.