6MP 180° Panoramic Analog High Definition Bullet Camera DWC-PB753WTW ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
Table of Contents TABLE OF CONTENTS Introduction Features Parts and Descriptions Dimensions Installation Inside the Box Installation Instructions Cabling Instructions Connecting to Monitors Control Board Adjusting the Camera Angle 7 8 9 10 11 12 OSD Menu How to Acces the OSD Menus Module OSD Menu Exposure Color Day & Night Function Motion Privacy Setup 4th BNC Output Panoramic OSD Menu 13 14 15 18 Troubleshooting Warranty Information Specifications 4 5 6 19 20 21 22 24 27 29 30-31 32 3
FEATURES* Analog High Definition (AHD) HD over Coax Technology 3x2MP Panasonic 1/3" CMOS Sensor 6MP 180° Panoramic Camera STAR-LIGHT™ Super Low Light Technology 6MP Resolution at 30fps 3x 4.
PARTS & DESCRIPTION* POWER AHD 1CH AHD 2CH Sunshield AHD 3CH AHD 4CH ALARM RS485 Ball Neck Bracket Pan/Tilt Stoper Screw Lens Console Cap Set Screw 5
DIMENSIONS IN MILLIMETERS (MM/IN)* 113.2 [4.45”] 96.5 [3.8”] 275.0 [10.8”] 249.9 [9.83”] 105.5 [4.15”] 78.0 [3.
INSIDE THE BOX* Quick Manual Screw & Plastic Anchor-4pcs Template Sheet Test Monitor Cable Sunshield T-Wrench Sunshield Screws 7
INSTALLATION INSTRUCTIONS* 1. Using the mounting template or your own camera, mark and drill the necessary holes to mount the bracket to a wall or ceiling. 2. Pull all necessary wires through and make the proper connections. 3. Use the four (4) mounting screws to install the camera on the wall or ceiling. 4. Using the subshiled screws, secure the sunshiled cover to the camera’s housing.
CABLING INSTRUCTIONS* Use the diagram below to connect the camera to external devices: 1. Power: connect the camera to a proper power supply. 2~4. AHD BNC Outputs 1~3: Connect each of the camera’s lenses as a separate output to a DVR supporting AHD signal such as the VMAX AHD CORETM and VMAX A1TM. On the DVR side, each lens will be set as a different channel. 5. AHD Output 4: Connect all 3 of the camera’s lenses as a single output to a DVR supporting AHD signal such as the VMAX AHD CORETM and VMAX A1TM.
CONNECTING TO MONITORS* Use the diagram below to connect to a Monitor or CRT Monitor properly. 12VDC/24VAC AHD DVR Secondary Video Output* Monitor BNC Selection Switch (See page 13) Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection) All cameras are equipped with a second video output for on-site configuration. *NOTE: 2nd BNC Output will display video for 60 seconds.
CONTROL BOARD* Test Video Output OSD Joystick Controller 1 2 BNC Selection Switch Remove the console’s cover by rotating it counter-clockwise. Use the Joystick to control the camera’s OSD options.
ADJUSTING THE CAMERA ANGLE* CAUTION : 1 Do not rotate more than 360o. 2 Do not unnecessarily twist too many times.
HOW TO ACCESS THE CAMERA’S OSD MENUS* The camera has three separate sensors, each with its own OSD menu and settings. When adjusting the camera’s settings, each lens/ sensor will have their own set of values and settings and will be set separately. In addition, the camera offers a 4th BNC output of a combined 180o view as a single camera output. This output has an additional Panoramic OSD menu with special settings including sticthing and motion and patrol setup.
MODULE OSD MENU* EXPOSURE COLOR DAY & NIGHT SHARPNESS WHITE BAL. AUTO / COLOR / BW 0 ~ 20 BACKLIGHT OFF / HME / BLC / WDR DRC AUTO / AUTO-EX / PRESET / MANULAL 0 ~ 20 SAVE & EXIT / EXIT 0 ~ 20 0 ~ 20 BRIGHTNESS / SHUTTER / FOCUS ADJ OFF / LOW / MIDDLE / HIGH DEFOG COLOR GAIN EXIT JUMP MODE CDS THRES FUNCTION LENS CDS MARGIN EXIT JUMP SAVE & EXIT / EXIT OFF / ON AGC 0~10 STARLIGHT OFF / x4 ~ x32 3D DNR OFF / LOW / MIDDLE / HIGH EXIT JUMP SAVE & EXIT / EXIT MOTION MOTION DET.
EXPOSURE LENS The camera’s lens mode is set by default to AUTO. This allows the camera’s iris automatically. Under the LENS sub-menu, you can adjust the following settings: - Brightness: Adjust the camera’s brightness from 0~20. The higher the number, the brighter the image will appear. - Shutter: Set the shutter speed to AUTO, Manual, or FLC (Flicker-less mode). - If AUTO is selected: - Select NORMAL for INDOOR applications. - Select DEBLUR for OUTDOOR applications.
EXPOSURE BACKLIGHT OFF HME HIGHLIGHT MASKING EXPOSURE HME allows objects to appear clearly on the screen by masking extremely bright areas. To setup HME, set the level and color. The lower the setting, the darker the masking areas have to be. Select from: 0 ~ 20, default is 10. Color: Set the color of the HME mask.
DRC EXPOSURE DYNAMIC RANGE COMPRESSOR Enables dark areas in images to become more visible without overexposing the bright areas to create one perfect image. Select from: OFF / LOW / MIDDLE / HIGH. If WDR or DEFOG are enabled, the DRC menu is disabled. DEFOG Allows the camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image. AUTO / Manual: Select AUTO to have the WDR and DRC levels adjusted automatically. Set the DEFOG level from LOW / MIDDLE / HIGH.
COLOR WB MODE AUTO Auto Tracking White Balance Control mode compensates for color temperature changes between 2400Ko and 11000Ko. AUTO-EXAuto White Balance Control mode compensates for color temperature changes lower than 2000Ko and higher than 15000Ko. PRESET Preset fixes the white balance based on the current lighting automatically. MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN (see below). C-TEMP: Select the color temperature for the white balance setup.
DAY & NIGHT D&N MODE AUTO / COLOR / B&W AUTO: The camera will switch between color and B/W based on the AGC levels. - AGC THRESHOLD: Set when the camera switches between Day & Night. - AGC MARGIN: Set the value added to the AGC Threshold. Adjust the value based on the environment in which the camera is installed. If the margin is too low, the camera will switch from color to B/W and back. - EXT. LED: If set to AUTO: the LEDs are enabled/ disabled by the CDS Sensor on the LED Board.
FUNCTION SHARPNESS 0 ~ 10 20 Sets the image sharpness. The higher the number, the sharper the image.
MOTION The camera can detect motion and display an alarm on the screen. Motion detection settings must be adjusted for each sensor. DET. WINDOW - WINDOW ZONE: Select a zone to setup from the 4 zones available. - WINDOW USE: Enable or disable the selected motion zone. - DET H-POS: Move the Zone left or right. The higher the number, the zone will move to the right. - DET V-POS: Move the Zone up or down. The higher the number, the zone will move down. - DET H-Size: Adjust the zone‘s size horizontally.
PRIVACY You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking zones are available. The cameras support square privacy masks or advanced polygon masks. BOX - ZONE NUM.: Select the zone number you want to setup. - ZONE DISP.: To enable it, turn the display option ON. - H-POS: Move the Zone position Left or right. The higher the number, the zone will move to the right. - V-POS: Move the Zone position up or down. The higher the number, the zone will move down.
PRIVACY You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking zones are available. The cameras support square privacy masks or advanced polygon masks. POLYGON MASKS - ZONE NUM.: Select the zone number you want to setup. - ZONE DISP.: To enable it, turn the display option ON. - POS0-X: Move the mask’s upper left angle left to right. - POS0-Y: Move the mask’s upper left angle up and down. - POS1-X: Move the mask’s upper right angle left to right.
SETUP CAM. TITLE Add a name to the camera. Set the title by using the OSD joystick. FREQUENCY* When the camera’s image has flickering issues, change the frequency value to adjust the image. LANGUAGE Select from the following: English (Default), Chinese, Chinese (S), and Japanese. *NOTE: Frequency setup menu is available on the 2nd sensor only. Settings adjusted in the 2nd sensor will be applied to the 1st and 3rd sensors.
SETUP DEFECT DET. The camera can detect and correct dead pixels in the image. Press the select button and set the threshold level. The camera will detect and adjust the pixels automatically. INITIAL Reset the camera to its default settings. Press and hold the select button for five (5) seconds.
EXIT EXIT SAVE&EXIT 26 Exit the OSD menu without saving any changes. Exit the OSD menu after saving the recent changes.
4th BNC OUTPUT PANORAMIC OSD MENU* MOTION When enabled, the camera will focus into the sensor’s display where motion is detected. This feature is available only in the 4th BNC output, when the camera’s image is displayed as a 180o view as a single camera output. The focused area will be shown in the top screen above the panoramic camera view. This motion alarm is not related to the individual channel motion setup. To enable, change the value to ON.
4th BNC OUTPUT PANORAMIC OSD MENU* STITCH Use this menu to adjust the stitching between each of the cameras as needed. You can adjust each individual camera’s position by selecting the camera name and move the image up, down, left and right to align with the camera next to it. Once the individual cameras’ position is properly adjusted, select FIX and exit the STITCH menu to save the stitching changes. It is not recommedned to manually adjust the camera’s stitching.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. FOR NO VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current. FOR OUT-OF-FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows: LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge.
LIMITS & EXCLUSIONS* There are no express warranties except as listed. The warrantor will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* VIDEO Image Sensor Active Pixels Scanning System Frequency Signal Technology Synchronization Resolution Minimum Scene Illumination S/N Ratio Video Output Alarm Output 3x Panasonic 1/3” CMOS Sensors 3X 1944 (H) x 1092 (V) Progressive scan 60Hz/50Hz 6.0 Megapixel AHD (3 x 2MP Sensors) Internal 6.0 Megapixel (3x 1920x1080 Sensors) F2.0 (30IRE): 0.06Lux [Color] F2.0 (30IRE): 0.
SPECIFICATIONS* OPERATIONAL (CONT.) White Balance Day and Night Auto Gain Control Motion Detection Privacy Zones RS485 Digital Zoom Auto / Auto-Ex/ Preset / Manual Day/ Night/ Auto Max 60dB 3 Zones per Camera, total 12 Motion Zones 16 Masks per Camera, total 72 Privacy Masks PELCO D/PELCO C x1.0 ~ x16.
MEMO* 34
MEMO* 35
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
