Quick Guide

Ethernet
Cable
1
Ethernet
Cable
2
Panning
360°
Rotation
360°
Tilting 90°
Mounting Template
Resetting the camera: To reset the camera, detach the ball
module from the base by rotating it counter-clockwise. See the
diagram on the bottom right.
Do not touch any other parts of the camera.
Press the reset button on the base of the camera’s lens module.
Pressing the button for five (5) seconds will initiate a camera-wide
reset of all the settings, including network settings.
When replacing the camera’s ball module back into place, make
sure no cables are caught or got disconnected. Rotate the ball
module clockwise until it is secured in place.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – POWERING THE CAMERA
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply
Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.59A
(DWC-MPVA5WiAT, DWC-MVA5WiAT, DWC-MPVA5Wi28T and
DWC-MVA5Wi28T), 0.53A (DWC-MPVA2WiAT, DWC-MVA2WiAT,
DWC-MPVA2Wi28T and DWC-MVA2Wi28T) min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with
the output evaluated as a Limited Power Source as defined in
UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
Pass the wires through and make all the necessary connections.
1. NETWORK CONNECTIONS - If you are using a PoE switch, connect
the camera using an Ethernet cable for both data and power.
2. NETWORK CONNECTIONS - If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
Models Power requirements Power consumption
DWC- MPVA5WiAT
DWC- MVA5WiAT
DC 12V, PoE IEEE 802.3af
Class 3.
(Adapter not included)
DC12V: max 7.1W
PoE: max 8.5W
DWC-MPVA5Wi28T
DWC-MVA5Wi28T
DC12V: max 6.5W
PoE: max 7.8W
DWC- MPVA 2WiAT
DWC- MVA2WiAT
DC12V: max 6.4W
PoE: max 7.6W
DWC-MPVA2Wi28T
DWC-MVA2Wi28T
DC12V: max 5.7W
PoE: max 7.2W
Quick Start Guide
Quick Start Guide
Tel: [phone]
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for the initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
a
b
c
2. Once all cables have been connected, use the screws included with
the camera to properly mount and secure the camera to the
mounting surface.
3. Adjust the camera’s pan, tilt and position to achieve the desired view.
The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotation: 0° ~ 360°
3. Once the installation is complete,
tighten the pan/tilt/rotation
screw until it’s secure.
STEP 3 – INSTALLING THE CAMERA
1. To use the camera’s waterproof wiring:
a. Install the LAN cable into .
b. will be assembled
to with a 1/4 turn.
c. Thread tightly to .
a
a
b
bc
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
a
b
NOTE: When using the waterproof cap, crimp the RJ45 connector
after passing the cable through the waterproof cap.
Default Login Information: admin | admin
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
DW® IP Finder™ software or directly from the camera’s browser menu.
MEGApix® IVA™ models 5MP models 2.1MP/1080p models
DWC-MPVA5WiAT DWC-MVA5WiAT DWC-MVA2WiAT
DWC-MPVA5Wi28T DWC-MVA5Wi28T DWC-MVA2Wi28T
DWC-MPVA2WiAT
DWC-MPVA2Wi28T
WHAT’S IN THE BOX
Hexagonal
Wrench
1
Mounting
Template
1
Screws and
Plastic
Anchors –
2pcs
1 set
Quick Setup
and
Installation
Guide
1 set
Waterproof
Cap and
Gasket
1 set
Screw &
Plasc Anchor-3pcs
Template Sheet
for installing by Plate
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut Mount Plate Torx Wrench
Waterproof cap & Gasket
Quick Manual &
Download Guide
Moisture absorber
& Absorber Guide
Test Video Cable