Quick Start Guide

Lens Specifications
Lenses are pre-focused at the factory. In the unlikely event that
the optical effect of the dome cover cause a slight defoucsing
of the lens, hold the dome cover over the lens to make a final
adjustment.
MD421D/B
MD421TIR/B
IP 2.1MP Snapit Indoor Dome Camera
Quick Setup Guide
Prepare the Camera and Mounting Surface
SPECIFICATIONS
Network Connection
There are two options.*
Using a Non-PoE Switch
Y-Axis: 90
o
Tilt for MPA20M
75
o
Tilt for MPA20MTIR
X-Axis: 360
o
Pan
1
2
!
Over-rotating the lens will damage the camera lens module
!
Frequent use may cause a System Error
Using a PoE-Enabled Switch
The MEGAPIX Camera is PoE-compliant, allowing transmission of power and data via a single
ethernet cable. Follow the illustrations below to connect the camera to a PoE-enabled switch using
an ethernet cable.
If a PoE-enabled switch is not used, use a power adaptor to connect the MEGAPIX Camera to a
Non-PoE switch.
Remove the camera’s protective bubble dome
by holding and squeezing the plastic dome on
both sides to lossen the hold on the camera
module.
Use camera mounting template or your
camera to mark the holes as required.
3
Drill holes into the drywall and insert the
drywall mounts.
4
Mount the Camera
The MEGAPIX Camera is designed to be surface mounted on a wall
or ceiling.
Pull wires through and make
connections. Refer to “Network
Connection” for further explanation.
5
Mount the camera to the wall or ceiling
using the screws provided with the camera.
6
Adjust the camera’s pan and tilt.
7
Snap the Cover Dome back
over the camera to complerte
the installation.
9
2
6 8
Check the LED Light. Green light flickers
for booting. Red light turns on when booting
is complete.
8
To snap the cover back into place,
align the small indentation in the cover
dome with the RJ45 connector in the
camera module as seen in the image.
10
Additional Cabling Connections
Resetting the Camera
Pressing the reset button on the camera’s control board for five (5) seconds will initialize all environmental
variables to factory default. Previous setup for IP default, time, etcetera will be deleted. If a system IP address is
lost, reset the camera back to factory default.The following are the default network settings:
IP Mode DHCP
IP Address 192.168.1.123
Subnet Mask 255.255.255.0
Gateway 192.168.1.123
Command Port 7000
HTTP Port 80
Live Port 7001
Thank you for purchasing Digital Watchdog’s Snapit MEAPIX lndoor Dome Camera.
Before installing the camera, please verify your model and read this guide carefully.
12132012
The following items are included with the MD421D/TIR camera
1
2
1
2
Camea Module
Snapit Indoor
8P Terminal
Block
Housing
PREPARATION
TEL: [phone]
www.Digital-Watchdog.com / [e-mail]
Technical Support Hours: Monday-Friday 8:30AM to 8:00PM EST
INSTALLATION
Quick Start
Guide
CD
(Manual &
Software)
Mounting
Template
2 Screws
2 Dry Wall
Anchors
1
2
1
While squeezing the plastic dome, hold the
camera module and gently remove it from the
bubble dome.
2
3 5 7
4
Camera Specifications
Second Video
Jack
NETWORK
OPERATIONAL
ENVIRONMENTAL
LENS
Storage Temperature -20
o
C ~ 70
o
C (-4
o
F ~ 158
o
F)
IMAGE
Image Sensor 1/2.8” CMOS Sensor (7% Larger Than 1/3” CMOS Sensor)
Total Pixels 2016 (H) X 1108 (V)
Minimum Scene Illumination F1.6 (30IRE): 0.5 Lux [Color]
F1.6 (30IRE): 0.0 Lux [B&W]
Lens Type Auto Focus
Focal Length 3.5-16mm
Frame Rate Up to 30fps at All Resolutions
Video Compression Type H.264, MPEG4, MJPEG (Super Fine~Low)
IP IPv4, IPv6
Protocol TCP/IP, HTTP, DHCP, PPPoE, ICMP, ARP, RARP,
RTSP, NTP, UDP, Multicast
LAN 802.3 Compliance 10/100 LAN
Web Viewer OS: Windows XP / Vista / 7, MAC OS
Browser: Internet Explorer, Chrome, Firefox, Safari
Video Management Software NxMS, Pivot
ONVIF Conformance Yes
Streaming Capability
Power Requirement DC 12V, PoE (IEEE802.3af Class 2)
Power Consumption 5.16W, 430mA / LED ON 9.96W, 830mA
Operating Humidity Less than 90% (Non-Condensing)
Operating Temperature/ Humidity -10
o
C ~ 55
o
C (14
o
F ~ 131
o
F)
CE, FCC, RoHS
Memory Slot Up to 24 Hour to Micro SDHC Card (4GB-32GB)
Card Not Included*
Dimensions 108 X 96.8 mm (4.25 X 3.8 in)
Material Plastic
Weight 0.529 lbs
Mirror & Flip
Maximum User Access 20 Users
Motion Detection: Sensitivity Low, Middle, High
Privacy Zone
MECHANICAL
ELECTRICAL
Resolution 1920X1080 (16:9) ~ 320X240 (4:3)
Digital Zoom / Optical Zoom 8X / 4.5X
IR Distance 70ft Range
Audio Cable
22
Rotation 360 Panning 360
NO IR IR NO IR IR
Tilting 90
NO IR
Tilting 75
IR
3
3