Quick Guide

ManualsBrandsDigital Watchdog ManualsBullet Cameras8 Megapixel Network Bullet Camera IVA with 2.7-13.5mm Lens

Quick Start Guide Quick Start Guide

WHAT’S IN THE BOX

Star Wrench

(T-10)

Star Wrench

(T-20)

Test Monitor

Cable

Moisture

Absorber and

Installation

Guide

(Recommended)

Screws

and Plastic

Anchors -

4pcs

1 set

Waterproof Cap

and Rubber Rings

(Black: ø0.15”

(ø4mm), White:

ø0.19” (ø5mm))

PoE injector

and power

cable

(optional)

1 set

Quick Setup

and Download

Guides

1 set

Mounting

template

1 set

1. The mounting surface must withstand ﬁve times the

camera weight.

2. Do not let the cables get caught in improper places or the electric line

cover can be damaged. This may cause a short or ﬁre.

3. For the installation process, remove the sun-shield cover as needed.

4. Install the moisture packet in the camera’s external control panel.

a. Remove the Desi-Pack moisture absorber from the packaging.

b. Open the side cover to reach the external camera control panel.

c. Place the moisture absorber under the camera’s SD card slot.

Pass the wires through the mount bracket and make all necessary

connections.

1. If you are using a PoE switch, connect the camera using an Ethernet

cable for both data and power.

2. If you are using a non-PoE switch, connect the camera to the switch

using an Ethernet cable for data transmission and use a power

adapter to power the camera.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 3 – INSTALLING THE CAMERA

STEP 2 – CABLING THE CAMERA

Power requirements Power requirements Power consumption

DWC- M B 4 8WiATW

DWC- M PB48WiATW

DC12V, IEEE 802.3at PoE+ class

4 (Adapter not included)

DC12V: 10.2W

PoE: 16W

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’ search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

Default login information: admin | admin

When logging into the camera for the ﬁrst time, you will be prompted

to set up a new password. You can set the new password using the

DW® IP Finder™ software or directly from the camera’s browser menu.

Resetting the camera: To reset the

camera, press the reset button on the

external control panel for ﬁve (5)

second. The system will initiate a

camera-wide reset of all the settings,

including network settings.

Reset Button

Mounting template

WARNING: It is highly recommended that you install the moisture

absorber when mounting the camera. The moisture

absorber prevents moisture from being captured

inside the camera's housing, which may cause image

performance issues and damage the camera.

NOTE: The camera will generate enough heat to dry moisture

during operation. In most cases it will not need the

moisture absorber for more than the ﬁrst day. In cases

where the camera can experience a moisture issue,

users must keep the moisture absorber in the camera.

The moisture absorber has an approximately 6-month

life cycle, varying depending on the environment.

MEGApix® IVA+™ models MEGApix® IVA™ models

DWC- M PB48WiAT DWC- M B 4 8WiAT

5. Using the mounting template sheet or the camera itself, mark and drill

the necessary holes in the wall or ceiling.

NOTE: A PoE injector is required for proper camera power and

function. The injector is sold separately.

SI P

I PA

DESI PA

DESI PAK

ESI P

I PAK

1. Once all cables are connected, secure the camera to the mounting

surface using the included screws.

SD card slot

Reset button

Test video output

NOTE: To ensure moisture seal, make sure the o-ring is in

place between

and

. In extreme environments use

of an outdoor rated sealer is recommended.

NOTE: Cables with ø4.5mm to ø5.5mm thickness should use

the black rubber ring. Cables over ø5.5mm in thickness

should use the white rubber ring.

a. Pass the LAN cable through the waterproof cap, gasket and

the rubber ring.

b. Connect the LAN cable to the camera’s network port .

c. will be axed to with a ¼ turn counter-clockwise.

d. Thread and twist tightly to .

2. The waterproof cap set comes with two rubber rings with dierent

diameters. The black rubber ring has an internal diameter of ø0.15”

(ø4mm). The white rubber ring has an internal diameter of ø0.19”

(ø5mm). When using the waterproof cap, use the rubber ring best

suited for your network cable’s diameter.

3. Loosen the pan and tilt screws at the base of the camera’s bracket to

adjust the camera’s view and position.

Summary of content (2 pages)

PAGE 1
Quick Start Guide Quick Start Guide STEP 1 – PREPARING TO MOUNT THE CAMERA 1. MEGApix® IVA+™ models MEGApix® IVA™ models DWC-MPB48WiAT DWC-MB48WiAT The mounting surface must withstand five times the camera weight. 2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or fire. 3. For the installation process, remove the sun-shield cover as needed. 4. Install the moisture packet in the camera’s external control panel. a.
PAGE 2
Quick Start Guide STEP 4 – CABLING STEP 6 – DW® IP FINDER™ Use the diagram below to properly connect power, network, audio, alarm and sensors to the camera. Use the DW IP Finder software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client. N.O N.