Analog High Definition Bullet Camera DWC-B7753TIR ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
TABLE OF CONTENTS Introduction Features Parts and Descriptions Dimensions Installation Inside the Box Installation Instructions Connecting to Monitors Adjusting the Camera Angle Module OSD Menu 4 5 6 7 8 9 10 11-26 Troubleshooting 27 Warranty Information 28-29 Specifications 30-31 3
FEATURES* Analog High Definition (AHD) HD over Coax Technology STAR-LIGHT™ Super Low Light Technology 1/2.7” CMOS Sensor 1080P Resolution at 30fps 3.6mm Fixed Lens Smart IR™ with Intelligent Camera Sync.
PARTS & DESCRIPTION* Mounting Bracket Sunshield Adjusting Screws Sunshiled Cover Pan/Tilt Stopper Screw Lens 5
DIMENSIONS IN MILLIMETERS (IN)* 62.2 63.8 74.5 95.
INSIDE THE BOX* Included with Bullet Camera: 1 2 3 User Manual Mounting Template 4 Machine Screws and 4 Dry Wall Anchors 4 L-Key Analog High Definition Bullet Camera DWC-B6763TIR ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
INSTALLATION INSTRUCTIONS* 1. Using the mounting template or your own camera, mark and drill the necessary holes to mount the bracket to a wall or ceiling. 2. Pull all necessary wires through and make the proper connections. 3. Use the four (4) mounting screws to install the camera on the wall or ceiling. NPT 3/4” Pipe *Installation Using a Junction Box *Note: Electrical junction box and required screws sold separately.
CONNECTING TO MONITORS* Use the diagram below to connect to a Monitor or CRT Monitor properly. 12VDC CCTV Monitor Monitor Power Connection - 12VDC Voltage. All cameras are equipped with a second video output for on-site configuration.
ADJUSTING THE CAMERA ANGLE* 360 90 CAUTION : 1 Do not rotate more than 360o. 2 Do not unnecessarily twist too many times.
MODULE OSD MENU* LENS P-IRIS MANUAL / AUTO MANUAL DC INDOOR / OUTDOOR EXPOSURE SHUTTER AUTO / 1/30~1/50000 / X2~X30 AGC STAR-LIGHT 0 ~ 15 OFF / AUTO X2 ~ X30 BRIGHTNESS 1 ~ 100 DRC BACKLIGHT OFF WHITE BALANCE BLC ATW PUSH HME MANUAL LEVEL / AREA / DEFAULT / RETURN AREA / DISPLAY / BLACK MASK / LEVEL / MODE / DEFAULT / RETURN BLUE(0~100) / RED(0~100) AWB OFF / AUTO / ON (0 ~ 8) DEFOG OFF / AUTO RETURN DAY & NIGHT AUTO AGC / CDS COLOR B/W BURST / IR SMART/ AREA / RETURN EXT NR (Noise
LENS Manual mode supports the fixed board lens or the manual iris lens. If the camera includes a P-Iris lens, you can select this option to adjust the lens and iris settings. If P-Iris is selected, adjust the following: MODE: Select from AUTO or MANUAL. If AUTO is selected, the camera’s iris and lens will be adjusted automatically. LIMIT: If MANUAL is selected, the camera’s iris can be adjusted manually using the LIMIT value.
EXPOSURE SHUTTER Set the camera’s shutter speed from the available options (AUTO/1/30~1/50000/x2~x30/FLK) If Iris is set to AUTO in the lens menu, the camera’s shutter will be set automatically and the values in this menu will not be adjustable. If Iris is set to AUTO in the lens menu, the camera’s shutter speed will be deactivated. AGC 0~15 AUTO GAIN CONTROL AGC enhances the picture brightness in low light conditions.
EXPOSURE (CONT.) DRC DYNAMIC RANGE COMPRESSOR DEFOG Allows the camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image. - POS/SIZE: Set the location and size of the defog mask. Use the joystick controller on the camera’s board to adjust the De-Fog zone’s position. Press the enter key and use the joystick controller to adjust the zone’s size. - GRADATION: Sett the DEFOG level from 0 ~ 2. The higher the number, the stronger the Defog mask will be.
BACKLIGHT BLC BACK LIGHT COMPENSATION HME HIGHLIGHT MASKING EXPOSURE If BLC is selected, adjust the size nad position of the mask: - Level: Set the BLC levels LOW / MIDDLE / HIGH - AREA: Use the joystick controller on the camera’s board to adjust the zone’s position. Press the enter key and use the joystick controller to adjust the zone’s size. - DEFAULT: Return the BLC settings to their original default values. HME allows objects to appear clearly on the screen by masking extremely bright areas.
WHITE BALANCE ATW Auto Tracking White Balance Control mode compensates for color temperature changes between 2400Ko and 11000Ko. PUSH Push fixes the white balance based on the current lighting automatically. To use this function, press the ENTER key for five (5) seconds. MANUAL Control the white balance manually by changing RED and BLUE. RED: Adjusts the low color temperature in the image between 0 ~ 100. The default value is 42. BLUE: Adjusts the low color temperature in the image between 0 ~ 100.
DAY & NIGHT AUTO / models). COLOR / B&W/ EXT Day/ Night switch is based on the CDS levels (IR models) or AGC levels (non-IR The camera always stays in day/color mode. The camera always stays in night/B&W mode. The camera’s Day & Night settings are set according to an external IR LED board. AUTO For cameras with no IR LED Built-in: - D -> N Threshold (AGC): Set when the camera switches from day to night mode by the AGC value.
DAY & NIGHT (CONT.) COLOR If COLOR mode is selected, the camera’s display will always appear in color, regardless of the lighting condition. B/W - BURST: Select to enable or disable color burst when the camera switches from color to B/W. - IR SMART (0~15): Enable Smart IR and set the level. Higher values will make Smart IR stronger. - AREA: Set the Smart IR’s zone. Use the joystick controller on the camera’s board to adjust the zone’s position.
NR Smart DNR 3D DIGITAL NOISE REDUCTION 2DNR Set the Digital Noise Reduction values for general illumination. Select from LOW / MIDDLE / HIGH. If the 2DNR settings are set to HIGH, image sharpness may be affected. Set the Digital Noise Reduction values for very low light situations. Select from LOW / MIDDLE / HIGH. If the 3DNR settings are set to HIGH, lagging issues may appear when motion occurs.
SPECIAL CAM. TITLE Add a name to the camera. Set the title by using the OSD joystick. D-EFFECT FREEZE MIRROR NEG. IMAGE Freeze image from the camera at the selected moment. Reflects the camera: OFF / MIRROR / V-FLIP / ROTATE Display the camera’s view in negative colors. Mirror / Flip OFF MOTION Mirror ON Flip ON Mirror & Flip ON - SELECT: The camera supports up to 4 separate motion detection areas. Select which one to adjust.
SPECIAL (CONT.) MOTION - ALARM: VIEW TYPE: When motion is detected, select from the following display options: 1. OFF - do not display motion alarm 2. ALL - Show all motion zones when motion alarm is detected. 3. BLOCK - show the area where motion is detected as a solid block. 4. OUTLINE - Show the area where motion is detected as an outline only. OSD VIEW: If enabled, ALARM will appear on the screen when motion is detected. ALARM OUT: The camera supports 3.3V alarm output.
SPECIAL (CONT.) PRIVACY - SELECT: The camera supports up to 4 separate privacy zones. Select which one to adjust. - DISPLAY: There are three types of privacy masks you can apply. Select from MOSAIC, INV., or COLOR. - MOSAIC: The privacy mask will appear as a mosaic over the camera’s image. - INV.: The privacy mask will appear as a negative of the image behind it, reversing the colors and brightness. - COLOR: The privacy mask will appear as a block of color according to the settings in the COLOR menu.
SPECIAL (CONT.) LANGUAGE Select from the available options: English, Chinese 1, Chinese 2, German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Korean, Japanese, Arabic, or Hebrew. DEFECT - LIVE DPC: - AGC LEVEL: Set the AGC levels for the Live DPC. - LEVEL: Set the level of Live DPC based on the AGC levels. - BLACK DPC - POS / SIZE: Set the size and position for the DPC Zone. Use the joystick controller on the camera’s board to adjust the zone’s position.
SPECIAL (CONT.) DEFECT (CONT.) - WHITE DPC - POS / SIZE: Set the DPC Zone. Use the joystick’ controller on the camera’s board to adjust the zone’s position. Press the enter key and use the joystick controller to adjust the zone’s size. - START: Press START to begin the DPC test. The screen will get bright and compensate for the black defect. - DPC VIEW: Show the Defect pixels which have been compensated. - LEVEL: Set the range of DPC application. - AGC: Set the value level for AGC while DPC is on.
ADJUST SHARPNESS Set the sharpness of the image. The Sharpness values can be increased or lowered according to teh AGC levels in the camera’s view. If AUTO is selected, adjust the following values: - LEVEL: Set the sharpness level. The higher the number, the sharper the image will appear. - START AGC: Select the AGC value where the image’s sharp lines may start to appear smeared in low light. - END AGC: Select end AGC value for sharpness smearing in low light.
ADJUST (CONT.) COMET When the camera is connected to the VMAX AHD DVR series, enabling the COMET feature enhances the camera’s CVBS signal. The COMET function reduces the noise at high frequency as well as provide high resolution clear image quality. If the camera is connected to a non-AHD DVR, enabling the COMET function will only turn the camera’s image to B/W. EXIT SAVE & END Save all changes made to the camera’s settings and exit the OSD menu.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. FOR NO VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current. FOR OUT-OF-FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warranter”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows: LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warranter will repair or replace the unit with a new or refurbished product at its option at no charge.
LIMITS & EXCLUSIONS* There are no express warranties except as listed. The warranter will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* VIDEO Image Sensor Active Pixels Scanning System Frequency Signal Technology Synchronization Resolution Minimum Scene Illumination S/N Ratio Video Output 1/2.7” CMOS Sensor 1920(H) x 1080(V) Progressive scan 60Hz/50Hz 2.0 Megapixel AHD Internal 1920x1080 (1080p) F1.4 (30IRE): 1.0Lux [Color] F1.4 (30IRE): 0 Lux [B&W] 55dB AHD 1080p30fps/720p60fps/720p30fps LENS Focal Length IR Distance 3.
SPECIFICATIONS* OPERATIONAL (CONT.) Digital Noise Reduction White Balance Day and Night Auto Gain Control Motion Detection Privacy Zones Sharpness Gamma UTC Off, Low, Middle, High Auto / Push / Manual / AWB Auto / Color / B/W / EXT 0 ~ 15 Yes 4 Privacy Zones 0 ~ 10 0.45 ~ 1.
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
