User`s manual

44 • Vacon apfiff09 marine
Tel. +358
5
6.4 Input Signals
6.4.1 Basic Settings
Code
Parameter
Min
Max
Unit
Default
Cust
ID
Note
P2.4.1.1
Start/Stop logic
selection
0
7
0
300
Start
signal 1
(Default:
DIN1)
Start
signal 2
(Default:
DIN2)
0
1
2
3
4
5
6
7
Start fwd
Start/Stop
Start/Stop
Start pulse
Start
Start fwd*
Start*/Stop
Start*/Stop
Start rvs
Reverse
Run enable
Stop pulse
Mot.Pot UP
Start rvs*
Reverse
Run Enable
Table 6-5. Input signals: basic settings, G2.2.1
6.4.2 Digital inputs
Code
Parameter
Min
Default
Cust
ID
Note
P2.4.2.1
Start signal 1
0.1
A.1
403
Forward, See ID300
P2.4.2.2
Start signal 2
0.1
A.2
404
Reverse. See ID300
P2.4.2.3
Run enable
0.1
0.2
407
Motor start enabled (cc)
P2.4.2.4
Reverse
0.1
0.1
412
Direction forward (oc)
Direction reverse (cc)
P2.4.2.5
Preset speed 1
0.1
0.1
419
See preset speeds in basing
parameter group G2.1
P2.4.2.6
Preset speed 2
0.1
0.1
420
P2.4.2.7
Preset speed 3
0.1
0.1
421
P2.4.2.8
Motor potentiometer
reference DOWN
0.1
0.1
417
Mot.pot. reference decreases (cc)
P2.4.2.9
Motor potentiometer
reference UP
0.1
0.1
418
Mot.pot. reference increases (cc)
P2.4.2.10
Fault reset
0.1
0.1
414
All faults reset (cc)
P2.4.2.11
External fault (close)
0.1
0.1
405
Ext. fault displayed (cc)
P2.4.2.12
External fault (open)
0.1
0.2
406
Ext. fault displayed (oc)
P2.4.2.13
Acc/Dec time selection
0.1
0.1
408
Acc/Dec time 1 (oc)
Acc/Dec time 2 (cc)
P2.4.2.14
Acc/Dec prohibit
0.1
0.1
415
Acc/Dec prohibited (cc)
P2.4.2.15
DC braking
0.1
0.1
416
DC braking active (cc)
P2.4.2.16
Jogging speed
0.1
0.1
413
Jogging speed selected for
frequency reference (cc)
P2.4.2.17
IO reference 1 / 2 selection
0.1
0.1
422
IO reference selection:14 ID117
P2.4.2.18
Control from I/O terminal
0.1
0.1
409
Force control place to I/O terminal
(cc)
P2.4.2.19
Control from keypad
0.1
0.1
410
Force control place to keypad (cc)
P2.4.2.20
Control from fieldbus
0.1
0.1
411
Force control place to fieldbus
(cc)
P2.4.2.21
Parameter set 1/set 2
selection
0.1
0.1
496
Closed cont.=Set 2 is used
Open cont.=Set 1 is used
P2.4.2.22
Motor control mode 1/2
0.1
0.1
164
Closed cont.=Mode 2 is used
Open cont.=Mode 1 is used
See par 2.6.1, 2.6.12
P2.4.2.23
External Brake
Acknowledge
0.1
0.2
1210
Monitoring signal from
mechanical brake
P2.4.2.24
Cooling Monitor
0.1
0.2
750
Used when water cooled unit
P2.4.2.25
Enable Inching
0.1
0.1
532
Enables Inching function
* = Rising edge required to start