Indoor Dome Camera DWC-D2367WD DWC-D2367WTIR ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
TABLE OF CONTENTS Introduction Features Parts and Descriptions Dimensions Installation Inside the Box Mount Installation Instructions Connecting to Monitors Adjusting the Camera Lens Adjusting the 3-Axis Gimbal Module OSD Menu 4 5 6 7 8-9 10 11 12 13-24 Troubleshooting 25 Warranty Information 26-27 Specifications 28-29 3
FEATURES* 1/3” Sony Super HAD CCD II 620 TV Lines (B&W), 600 TV Lines (Color) 3.
PARTS & DESCRIPTION* 1 2 3 4 5 6 7 8 9 Lens Primary Video-BNC Output Connector Power Input Connector (12VDC/24VAC) Bottom Case Mounting Screws Black Lens Cover Bubble Dome Upper Case Ring Assembly Screws 3 2 4 1 5 6 7 8 9 5
DIMENSIONS IN MILLIMETERS (IN)* 134.9(5.31”) 46(1.81”) 110.3(4.34”) 64.3(2.
INSIDE THE BOX* Included with D2 Indoor Dome Camera 1 2 3 User Manual Mounting Template 2 Machine Screws and 2 Dry Wall Anchors 4 5 6 Miniature TORX Driver L-Key Secondary Video-BNC Cable 7
CAMERA INSTALLATION* 1 Cut a hole in the ceiling for routing the cables. Use your mounting template to mark the screw holes. 2 Drill holes into the drywall and insert the drywall mounts into the holes. 3 Pull wires through and make connections. 4 Mount and secure the camera to the surface using the machine screws. 5 Position the lens and adjust the zoom and focus. 6 Assemble the black lens cover and outer dome cover with the camera module.
WALL MOUNT INSTALLATION* 1 Check to see all parts are in the box. 2 Use the mount to mark the pilot holes are required. Drill holes into the drywall and insert the drywall mounts. 3 Secure the wall mount to the wall using the mounting screws. 4 Attach the base of the camera to the wall mount with the smaller machine screws. 5 Position the lens, and adjust the zoom and focus. 6 Assemble the black lens cover and outer dome cover with the camera module.
CONNECTING TO MONITORS* DC12V / AC24V Video Output BNC Cable Main Monitor Second Video Cable Field Test Monitor 10
ADJUSTING THE CAMERA LENS* Focus Handle Zoom Handle 1 2 3 4 Loosen the zoom and focus handles by rotating them counter-clockwise. Adjust the field of view by moving the handle to the RIGHT (tele) to zoom in or to the LEFT (wide) to zoom out. AFTER the desired zoom position is established, adjust the focus the same way as described above. Once the desired adjustments have been made, please tighten the handles back by turning them clockwise.
ADJUSTING THE 3-AXIS GIMBAL* The Gimbal mechanism yields maximum rotation and placement as shown below. 360.0° 12 360.0° 90.
MODULE OSD MENU* EXPOSURE LENS MANUAL / DC BACKLIGHT COLOR WB MODE AWC / ATW / MANUAL / PUSHLOCK AGC RED GAIN 0 ~ 255 BLUE GAIN STARLIGHT OFF / x2 ~ x1024 3D DNR COLOR MODE NORMAL / COOL / WARM EXIT JUMP OFF / BLC / HME / WDR OFF / LOW / MID / HIGH / HIGHEST OFF / LOW / MID / HIGH / SMART 0 ~ 255 DAY & NIGHT FUNCTION D&N MODE AUTO / COLOR / B&W NIGHT C. MIRROR / OFF 0 ~ 100 NIGHT A. EXIT JUMP 0 ~ 30 0 ~ 100 MANUAL / 0.45 / 0.60 / 1.
EXPOSURE LENS Manual DC Manual mode supports the fixed board lens or the manual iris lens. DC mode supports the auto-iris varifocal lens. NOTE: Both MANUAL and DC mode have FOCUS TARGET. You can adjust the focus by finding the highest number on the FOCUS TARGET. See page 16 for focus information. ELC Levels and DC Levels are adjustable. The higher the number, the brighter the image. E. Shutter sets the shutter speed levels from 1/60 to 1/100000. *For LENS-MANUAL Mode, the default E.SHUTTER is AUTO.
EXPOSURE BACKLIGHT OFF BLC BACK LIGHT COMPENSATION MANUAL User can manually adjust the BLC level in five areas of the scene (TOP, BOTTOM, CENTER, LEFT, RIGHT). Increase the BLC levels to make the image brighter. SMART This is recommended. Camera will automatically detect and adjust the BLC zone. BLC levels to choose from include: LOWEST, LOW, MID, HIGH. HME HIGHLIGHT MASKING EXPOSURE HME masks highlights to allow objects to appear clearly on the screen. If ON is selected, HME levels are adjustable.
EXPOSURE AGC OFF / LOW / MID / HIGH / HIGHEST STARLIGHT OFF / x2 ~ x1024 AUTO GAIN CONTROL AGC enhances the picture brightness in low light conditions. A higher level AGC setting makes the images brighter; however, it could increase the amount of noise. Starlight mode automatically activates slow shutter function when the image is too dark. x4 is the default. We do not recommend you to increase the setting, for it causes the image to lag. Note: Starlight menu cannot be controlled if the E.
COLOR WB MODE Auto White Balance Control mode compensates for color temperature changes between 2000K and 18000K. ATW Auto Tracking White Balance Control mode compensates for color temperature changes between 2500K and 9500K. MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN (see below). PUSHLOCK Pushlock is to fix the white balance based on the lighting. AWC RED GAIN 0 ~ 255 Adjusts the amount of red in the image.
DAY & NIGHT D&N MODE In AUTO mode, camera switches between day and night automatically depending on light level. Camera will stay in color mode when there is enough light and will switch to B&W at night or other low light environments. If COLOR is selected, camera always stays in day/color mode. If B&W is selected, camera always stays in night/B&W mode.
FUNCTION MIRROR OFF MIRROR Flips the image horizontally. SHARPNESS 0 ~ 30 Sets the image sharpness. The higher the number, the sharper the image. GAMMA 0.45 / 0.60 / Select the desired gamma level. 0.45 is default setting. 1.0 / MANUAL SLC (SIDE LIGHT COMPENSATION) OFF / ON Increase the brightness on sides of the image. NIGHT-UP OFF / ON Adjusts sensitivity in low light conditions by setup level. If ON is selected, the setup level becomes higher, and the images become brighter.
MOTION The camera can detect the movement and display an alarm on the screen when movement is detected. AREA SET AREA 1 ~ 4 OFF / ON SENSITIV. 1 ~ 30 If ON, motion areas can be selected and moved accordingly. Select Areas 1-4 and adjust using controls for TOP, BOTTOM, LEFT, or RIGHT. Sensitivity level of the motion detection is adjustable. Motion Detection will be more sensitive at a higher number. SHOW INDI. OFF / ICON Set the Show Indicator to OFF, ICON, or TRACE.
PRIVACY You can hide some parts of the screen for privacy masking. A total of 8 different privacy masking zones are available. MASK 1 ~ MASK 8 OFF / ON Select ON or OFF for each mask (MASK 1 through 8). If ON is selected you can set the area to be masked and the shape and color of the mask. *START POINT: Select the START POINT to adjust the size of the *privacy zone.
SETUP TITLE OFF / ON If ON is selected, you can display the camera title on the screen. *CLR: Clear the title. *POS: Position the title on the screen. DPC (DEAD PIXEL CANCELLATION) OFF DPC automatically removes defective pixels in real time. AUTO If AUTO is selected, you can define the following settings: *WHITE THR: Cancels the white defective pixels. *BLACK THR: Cancels the black defective pixels. *DPC LEVEL: Adjusts the sensitivity level of the dead*pixel cancellation.
SETUP LANGUAGE The camera supports the following languages: ENGLISH, CANTONESE, MANDARIN, JAPANESE, GERMAN, FRENCH, ITALIAN, RUSSIAN, SPANISH, AND DUTCH. OSD COLOR The following colors are available for the OSD menu: BLUE, GREEN, CYAN, RED, MAGENTA, YELLOW, PURPLE, and GRAY. COMMUNICATION OFF ON If ON is selected, you can define the following: *PROTOCOL: PELCO-D only. *CAMERA ID: Provide an ID number for the camera *(0~255). *BAUDRATE: 9600bps is the default.
EXIT EXIT SAVE & EXIT Exit the OSD after saving the current settings. EXIT Exit the OSD without saving.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. FOR NO VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the camera’s OSD menu. Check the power supply and make sure the camera has the proper voltage and current. FOR OUT-OF-FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment.
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows: LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge.
LIMITS & EXCLUSIONS* There are no express warranties except as listed. The warrantor will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* DWC-D2367WD & DWC-D2367WTIR VIDEO Image Sensor 1/3" Sony Super HAD CCD II Total Pixels 811 (H) x 508 (V), 411K Pixels Effective Pixels 768 (H) x 494 (V) Frequency 15.734KHz (H), 59.95Hz (V) Synchronization Internal or Line Lock Horizontal Resolution 620 TV Lines [B&W], 600 TV Lines [Color] Minimum Illumination F1.2 (30IRE): 0.14 Lux [Color] F1.2 (30IRE): 0.03 Lux [B&W]; 0.0 Lux [B&W] for IR Model S/N Ratio 50dB (AGC off) Video Output CVBS: 1.0Vp-p / 75 Ω LENS Focal Length 3.
ENVIRONMENTAL Operating Temperature Operating Humidity Storage Temperature ELECTRICAL Power Requirement Power Consumption MECHANICAL Housing Material Dome Cover Material Dimensions Weight -10oC ~ 55oC (14oF ~ 131oF) Less than 90% (Non-Condensing) -20oC ~ 70oC (-4oF ~ 158oF) Dual (12VDC & 24VAC) 12VDC: 1.8, 150mA / LED ON 4.6W, 383.3mA 24VAC: 2.4W, 100mA / LED ON 4.9W, 204mA Plastic Polycarbonate ∅134.9 X 110.3 mm (∅5.31 X 4.34 in) 0.79 lbs; 0.
MEMO* 30
MEMO* 31
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
