Specifications

ManualsBrandsDigital Security Controls ManualsHome building and DecorPC1575

1.1 Specifications

Control Panel Specifications

PC1575 (standard option): one low current PGM output

and one low current PGM output/input.

PC1575 (2-wire smoke option): one low current PGM

output and one high current PGM output/input.

Flexible Zone Configuration:

• Six fully programmable zones

• Seven Access Codes: five User, one Master and a

second Master code

• Normally Closed, Single EOL, Double EOL

• 2-wire Smoke Zone or Auxiliary Zone

• 21 Zone Types, 6 Programmable Zone Options

Audible Alarm Output:

• Supervised Bell Output (current limited at 3 amps), 12V

• Steady or Pulsed Output

EEPROM Memory:

• Does not lose programming or system status on

complete AC and Battery failure

Programmable Outputs:

• One programmable voltage output and one

programmable voltage output/input; 30 programmable

options

• PC1575 (standard option):

PGM1 = one low current (50mA) PGM output

PGM2 = one low current (50mA) PGM output/input.

• PC1575 (2-wire smoke option):

PGM1 = one low current (50mA) PGM output

PGM2 = one high current (300mA) PGM output/input

with 2-wire smoke detector capability

Please read Appendix D “PGM Output Options”

carefully for important information.

Powerful 1 Amp Regulated Power Supply:

• 550 mA Auxiliary Supply, 12 V

• Positive Temperature Coefficient (PTC) components

replace fuses

• Supervision for loss of AC Power, Low Battery

• Internal Clock Locked to AC Power Frequency

Power Requirements:

• Transformer = 16.5 V

AC, 40VA

• Battery = 12 volt 4 Ah minimum rechargeable sealed

lead acid

Remote Keypad Specifications:

• Three Different Keypads Available:

- PC5506 six zone LED keypad

- LCD5500 Alphanumeric keypad

- PC1575RK six zone LED keypad

- SL-75 six zone LED keypad

• The PC5506 and LCD5500 keypads have 5 Fully

Programmable Function Keys

• Connect up to 8 Keypads

• Four Wire (Quad) Connection to KEYBUS

• Built in Piezoelectric Buzzer

SECTION1

Digital Communicator Specifications:

• Supports Major Formats including SIA and Contact ID

• Event Initiated Personal Paging

• Three Programmable Phone Numbers

• Two Account numbers

• Supports LINKS 1000 Cellular Communication

• DTMF and Pulse Dialing

• DPDT Line Seizure

• Anti-jam Feature

• Split Reporting of Selected Transmissions to Each

Telephone Number

System Supervision Features:

The PC1575 continuously monitors a number of possible

trouble conditions including:

• AC Power Failure

• Trouble by Zone

• Tamper by Zone

• Fire Trouble

• Telephone Line Trouble

• Failure to Communicate

• Low Battery Condition

• Bell Output Trouble

• Module Fault (Supervisory or Loss of Internal Clock

AUX Power Supply Fault Tamper)

False Alarm Prevention Features:

• Audible Exit Delay

• Audible Exit Fault

• Communication Delay

• Urgency on Entry Delay

• Quick Exit

Additional Features:

• Auto Arm at Specified Time

• Keypad Activated Alarm Output and Communicator

Test

• All modules connect to the system via a four wire

KEYBUS up to 1000’/300m from main panel

• Event Buffer can be printed using PC5400 RS232 Serial

Interface module

• Supports the ESCORT 5580 Voice Prompt Module with

Automation/Lighting Control

• An Event Buffer which records the past 100 events with

both the time and date at which they occurred

• Uploading and Downloading capability

• Local Downloading capability through the use of the

PC-LINK Adaptor

UL Installation

This equipment is UL Listed in accordance with UL1023

(Household Burglar Alarm System Units), UL985 (Household

Fire Warning System Units), UL1635 (Digital Alarm Annunciator

System Units), UL365 (Police Station Connected Burglar

Alarm Units and Systems), UL609 (Local Burglar Alarm Units

and Systems), UL1610 (Central Station Burglar Alarm Units).

This equipment has the capability of being programmed for

operational features that are not allowed for UL Listed Systems

or being connected to accessories not permitted.

Refer toRefer to

Refer to

Appendix E for summary of requirements.Appendix E for summary of requirements.

Appendix E for summary of requirements.

PC1575 System Introduction

Summary of content (43 pages)

PAGE 1
PC1575 System Introduction S E C T I O N 1 Digital Communicator Specifications: • Supports Major Formats including SIA and Contact ID • Event Initiated Personal Paging • Three Programmable Phone Numbers • Two Account numbers • Supports LINKS 1000 Cellular Communication • DTMF and Pulse Dialing • DPDT Line Seizure • Anti-jam Feature • Split Reporting of Selected Transmissions to Each Telephone Number 1.
PAGE 2
S Y S T E M V I N T R O D U C T I O N 1.2.4 Downlook Video Transmission Module The Downlook Still-Frame Video Transmission Module (DLM1/DLM-4) is the ideal solution for all business and residential environments which require visual surveillance but where the presence of on-site security personnel is impossible, undesirable or unaffordable.
PAGE 3
Getting Started S E C T I O N 2 programmable features, which options are available and how they function. The Programming Worksheets (pages 25-33) should be filled out completely before attempting to program the system. The following Sections provide a thorough description of how to wire and configure devices and zones. 2.1 Installation Steps The following steps are provided to assist you with installing the panel. We suggest that you read this section completely before you begin.
PAGE 4
G E T T I N G S outgoing line to house telephone(s) T E D C A Telephone Connection Terminals – TIP, RING, T-1, R-1 If a telephone line is required for central station communication or downloading, connect an RJ-31X telephone jack in the following manner: • T-1 - Grey Wire • R-1 - Brown Wire R B Zone Input Terminals – Z1 to Z6 Each detection device must be connected to a zone on the control panel.
PAGE 5
G E T T I N G S T A R T E D 2.8.2 Single End Of Line (EOL) Resistors (5600Ω) 2.6 Supervision By default, all modules are supervised upon installation. Supervision is enabled at all times so that the panel can indicate a trouble if a module is removed from the system. A connected module which does not show as being present will appear as a trouble condition and the Trouble light on the keypad will turn ON.
PAGE 6
G E T T I N G S T A R T E D 2.8.8 LINKS Supervisory When using the LINKS 1000 cellular communicator, any zone may be configured for LINKS Supervisory. With a LINKS Supervisory zone, if the LINKS 1000 experiences a trouble, the zone will be violated, causing the panel to report the event to the central station. This type of zone always requires a single EOL resistor (5600Ω). The LINKS Supervisory zone must be wired according to the accompanying diagram.
PAGE 7
Keypad Commands S E C T I O N 3 zones, such as designated entry/exit doors. If no delay type zone is violated by the end of the exit delay, the panel will bypass all Stay/Away type zones. The Bypass light will remain ON to inform the user that the interior protection has been automatically bypassed by the panel. If a delay zone is violated during the exit delay, the Stay/Away zones will be active after the exit delay expires.
PAGE 8
K E Y P A D V C O M M A N D S To view trouble conditions from an LED keypad: 1. Press [✱] [2]. zone—due to a bad contact or damaged wiring—until service can be provided. If the Code Required for Bypass option is enabled, only user codes with the bypass attribute will be able to bypass zones (see Section 5.1 “Programming Security Codes”).
PAGE 9
K E Y P A D V C O M M A N D S Access code (1) ............................ One Master Code Access codes (2) to (6) ................. Five User Codes All access codes have the ability to arm or disarm the system and can activate the PGM Outputs using the [✱] [7] [1] [Access Code] and [✱] [7] [2] commands. reporting code(s) programmed in section [45] will be transmitted along with the unreported events from an earlier unsuccessful communication.
PAGE 10
K E Y P A D V C O M M A N D S Keypad Beeper Control The LCD keypad will allow you to select from 21 different keypad beeper tones. Use the arrow keys (< >) to scroll to the desired keypad beeper level and press the [#] key to exit. This featured can be accessed on LED keypads by holding the [✱] key. • [2] – Auto-Arm Enable/Disable Auto-Arming will not work unless it is enabled for the system. To enable or disable auto-arming, press [2].
PAGE 11
K E Y P A D V C O M M A N D S [05] – [✱ ] [9] No-Entry Delay Arm Once this function key is pressed the user must enter a valid user code. The system will arm and remove the entry delay from the system when the exit delay expires (see Section 3.4 – “[✱] [9] Arming Without Entry Delay”). 3.
PAGE 12
How to Program S E C T I O N 4 4.2 Programming Decimal Data The following section of the manual describes the Installer’s Programming function and how to program the various sections. A set number of programming boxes are allotted for each section requiring decimal data (e.g.: codes, telephone numbers). If a digit is entered for each program box, the panel will automatically exit from the selected programming section. The Ready light will turn OFF and the Armed light will turn ON.
PAGE 13
H O W V T O V P Refer to Section 5 in this manual to determine what each option represents and whether the light should be ON or OFF for your application. R O G R A M Press any of the Emergency Keys (Fire, Auxiliary or Panic) to advance to the next digit. When all the digits in a section have been viewed, the panel will exit the section; the Ready Light will turn OFF and the Armed light will turn ON, waiting for the next two digit programming section number to be entered.
PAGE 14
Program Descriptions S E C T I The following section explains the operation of all programmable features and options and provides a summary of all corresponding programming locations. O N 5 begun, it will cause an instant alarm. Typically, this zone is used for interior protection devices, such as motion detectors.
PAGE 15
P R O G R A M D E S I P T I O N S Zones Attributes ....... Sections [21] - [26], Options [1] - [6] ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5.4 Communicator – Dialing If the Communicator Disable option is selected, the panel will not attempt to call central station. If communication is enabled, the panel will attempt to call central station when an event with a valid Reporting Code occurs (See Section 5.7 “Communicator – Reporting Code”).
PAGE 16
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Phone numbers can be up to 32 digits which will allow you to add special digits if required. To program the phone number, enter the numbers 0 through 9 as required.
PAGE 17
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ the Fire Keys on any keypad are pressed for two seconds. The panel will transmit a Keypad Auxiliary Alarm Reporting Code and the Keypad Auxiliary Restoral Reporting Code when the Auxiliary Keys on any keypad are pressed for two seconds.
PAGE 18
P R O G R A M D E S • 3/1, 3/2, 4/1 or 4/2 • 1400 or 2300 Hz handshake • 20 bits per second • non-extended Additional Notes on Pulse Formats 1. The digit ‘0’ will send no pulses and is used as a filler digit. C R I P T I O N S 2. If the Reporting Code for an event is programmed as anything from [01] to [FF], the panel will automatically generate the zone or user code number.
PAGE 19
P R O G R A M D E S C R I P T I O N S 5.10 Telephone Line Monitor (TLM) When power is applied to the panel, downloading will be enabled for six hours. This will allow you to perform downloading without having to do any keypad programming. The panel will supervise the presence of the phone line and will indicate a trouble condition if the phone line is disconnected.
PAGE 20
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Periodic Test Transmission Reporting Code .. Section [46] Test Transmission Time of Day ........................ Section [63] Test Transmission Cycle .................................. Section [62] LINKS 1000 Test Transmission Reporting Code Section [46] System Test Reporting Code ...........................
PAGE 21
P R O G R A M D E S By default, the Swinger Shutdown limit is set to [003]. The panel will not send more than three alarm signals for each zone until the Swinger Shutdown is reset. Swinger Shutdown will be reset every day at midnight or when the panel is armed. Once reset, the panel will again communicate normally. C R I P T I O N S 5.20 Keypad Blanking If the Keypad Blanking option is enabled, the panel will turn off all lights on the keypads when no keys are pressed for 30 seconds.
PAGE 22
P R O G R A M D E S LINKS is Backup of Land Lines option must be selected.
PAGE 23
Programming Worksheets NOTE: For UL listed systems, refer to the UL Requirements section in Appendix E.
PAGE 24
P R O G R A M M I N G W O R K S H E E Keypad Programming P R O G R A M M I N G W O R K S H E E T S [00] Keypad Assignment (Section 2.6 “Keypad Assignment”) Note: This must be done at each keypad requiring programming.
PAGE 25
P R O G R A M M I N G W O R K S H E E T S [03] Installer’s Code (Section 4 “How to Program”) Default 1575 I_______I_______I_______I_______I [04] Master Code (Section 5.1 “Pr “Programming ogramming Security Codes”) Default 1234 I_______I_______I_______I_______I [05] Second Master Code (Section 5.
PAGE 26
P R O G R A M M I N G W O R K S H E E T [10] Third System Option Code Default OFF OFF OFF OFF ON ON I________I I________I I________I I________I I________I I________I Option 1 2 3 4 5 6 ON Arm / Disarm Bell Squawk Enabled Bell Squawk During Auto Arm Bell Squawk On Exit Delay Bell Squawk On Entry Delay Audible Exit With Urgency Quick Arm Enabled OFF Arm / Disarm Bell Squawk Disabled No Bell Squawk During Auto Arm No Bell Squawk On Exit Delay No Bell Squawk On Entry Delay Silent Exit De
PAGE 27
P R O G R A M M I N G W O R K S H E E Communicator Programming P R O G R A M M I N G W O R K S H E E T S Note: For sections [31] to [46], the contents of every section by default is [F]. [31] First Telephone Number (32 Digits) (Section 5.
PAGE 28
P R O G R A M M I N G W O R K S H E E T S [42] Opening (Disarming) Reporting Codes, Access Codes 1-6 (Section 5.
PAGE 29
P R O G R A M M I N G W O R K S H E E T S [53] Openings & Closings Communicator Call Directions (Section 5.4 “Communicator – Dialing”) Default ON OFF OFF OFF Option 1 2 3 4 I________I I________I I________I I________I ON 1st Telephone Number 2nd Telephone Number 1st Telephone Number (via LINKS) 2nd Telephone Number (via LINKS) OFF Disabled Disabled Disabled Disabled [54] System Maintenance Alarms & Restorals Communicator Call Directions (Section 5.
PAGE 30
P R O G R A M M I N G W O R K S H E E T S [67] LINKS 1000 Preamble (First Telephone Number) (Section 5.23 “LINKS 1000 Cellular Communicator”) Default FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F) [68] LINKS 1000 Preamble (Second Telephone Number) (Section 5.23 “LINKS 1000 Cellular Communicator”) Default FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F) [69] LINKS 1000 Preamble (Third Telephone Number) (Section 5.
PAGE 31
P R O G R A M M I N G W O R K S H E E T S Module Programming P R O G R A M M I N G W O R K S H E E T S [87]PC5400 Programming (Printer Module) (Section 5.
PAGE 32
Contact ID A P P E N D I X A The Partition ID Codes must be 4 digits. All reporting codes must be 2 digits. The following is a list of Contact ID reporting codes. The first digit (in parentheses) will automatically be sent by the control. The last two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the alarm reporting code could be programmed as [34].
PAGE 33
SIA Format A P P E N D I X B SIA Format Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - February 1993. This format will send the Account Code along with its data transmission.
PAGE 34
Programming LCD Keypads A P P E N D I X C If you have an LCD5500 Keypad, additional programming is required for proper operation. The following is a description of the available programming options and their accompanying programming sections: How to Enter LCD Programming Follow the programming procedure as outlined in Section 4 by pressing [✱] [8] [Installer’s Code]. Press the [✱] key. Enter the two digit Section number to be programmed.
PAGE 35
P R O G R A [62] Third User Display Mask Default Option ON I_______I 1 I_______I 2 ON I_______I 3 ON I_______I 4 ON ON I_______I 5 I_______I 6 ON I_______I 7 ON I_______I 8 ON M M M I N G L ON System Test prompt ON Time and Date prompt ON Auto-Arm Control prompt ON Auto-Arm Time prompt ON Download Enable prompt ON Bright Control prompt ON Contrast Control prompt ON Buzzer Control prompt ON C D K E Y P A D S OFF System Test prompt OFF Time and Date prompt OFF Auto-Arm Days prompt OFF
PAGE 36
PGM Output Options A P P E N Establishing PGM Output Types Each PGM output is designed so that when activated by the panel, the terminal will switch to ground. PGM 1 – 50mA Current PGM1 can sink up to 50 mA of current to activate LEDs or a small buzzer. Connect the positive side of the LED or buzzer to AUX+, the negative side to PGM1. If more than 50 mA of current are required, a relay must be used. Please study PGM wiring in the accompanying diagram.
PAGE 37
P G M O U T P U [11] TLM and Alarm The PGM output switches to ground when the system experiences both a telephone line trouble and an alarm. When the system is armed, the output will deactivate only if an access code is entered. If the output is activated by an alarm in the disarmed state, it will only deactivate if the bell is silenced during bell time-out or if the system is armed after the bell time-out. This output will activate for all silent and audible alarms except the Duress alarm.
PAGE 38
Appendix E U L R E Q U The following requirements apply to UL Listed systems: 1. All components of the system should be UL listed for the intended application. 2. If this system is configured for “fire”, the installer should refer to chapter 2 of NFPA 72 for details in locating smoke detectors and the typical installation layout shown below. 3. Note that at least one UL listed compatible audible signal appliance shall be installed indoors. 4.
PAGE 39
Control Panel Wiring Diagram
PAGE 40
NOTICE! You must read this entire manual, including all notices and warnings, in order to install this system so that it is fully functional. WARNING! This entire system must be completely tested on a regular basis to verify the operation of all system functions, in accordance with the recommendations of the security systems industry.
PAGE 41
T A B L E V O F 5.8 Communicator – Reporting Formats ................................ 17 5.8.1 Pulse Formats ....................................................... 17 5.8.2 Contact ID ............................................................. 18 5.8.3 SIA ........................................................................ 18 5.8.4 Pager Format ........................................................ 18 5.9 Downloading .....................................................................
PAGE 42
Industry Canada Notice AVIS: L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication.
PAGE 43
© 1997 Digital Security Controls Ltd. 1645 Flint Road, Downsview, Ontario, Canada M3J 2J6 Tel. (416) 665-8460 • Fax (416) 665-7498 • Tech.