User's Manual
Table Of Contents
- Table of Contents
- WARNING: Installer please read carefully
- General
- Model Information
- Panel Mounting
- Features
- Technical Specifications
- Ratings Compatibility
- Pre Installation Configuration
- Communicator Installation Configuration
- Installing Communicator in Panel
- Communicator Placement Test
- Initial Panel Programming
- SMS Command and Control
- Communicator Status LEDs
- Yellow Trouble LED
- Panel Supervision Trouble (2 Flashes)
- SIM Lock Trouble (4 Flashes)
- Cellular Trouble (5 Flashes)
- Ethernet Trouble (6 Flashes)
- Receiver Not Available (7 Flashes)
- Receiver Supervision Trouble (8 Flashes)
- FTC Trouble (9 Flashes)
- Module Configuration Trouble (12 Flashes)
- Red Network Connection Status LED
- (Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength
- Network Activity LEDs - Red and Green(TL2803G(R)E / TL280LE(R) only)
- Communicator Troubleshooting
- Ethernet/Cellular Programming Options
- System Options
- Programming Options
- Communications Reporting Codes
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- SMS Event Notification/Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Ethernet Cellular Programming Worksheets
- System Options
- Programming Options
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Limited Warranty
- EULA
- Regulatory Information
Event [Section] Label Default Label Event [Section] Label Default Label
[869] Keypad Message (Keypad Message) [870] Function Successful (Successful)
[871] Function Failure (Unsuccessful) [872] Invalid Command (Invalid Command)
[873] System Stay Armed (Stay Armed) [874] System Away Armed (Away Armed)
[875] System Night
Armed
(Night Armed)
[876] System Disarmed
Ready
(Disarmed Ready)
[877] System Disarmed,
Not Ready
(Disarmed Not Ready) [878] System In Alarm (is in Alarm)
[879] Trouble Label (Service is Required)
[880] No Alarms in
Memory
(No Alarms in Memory)
[881] Pay As You Go
Balance
(Pay as you go balance:)
[882] Pay As You Go
Message
(*123#)
[883] Response Code (Response Code)
Receiver Diagnostic Testing
[901] Diagnostic Test Transmission
[1] Ethernet 1 Default (OFF).
[2] Ethernet 2 Default (OFF).
[3] Cellular 1 Default (OFF).
[4] Cellular 2 Default (OFF).
[5],[6],[7],[8] Reserved (OFF).
This section may be used by the installer to force the communicator to send an immediate test trans-
mission to specific receivers, to verify that the communications paths are available. Diagnostic test trans-
mission failure will indicate as FTC trouble (yellow LED = 9 flashes). If an FTC error occurs when testing
all receivers, select only one receiver and repeat test to isolate the receiver that is not communicating.
NOTE: Sending a test transmission to a receiver that is not programmed generates an FTC trouble.
[961] Cellular Inactivity Timeout
Default (41) Valid entries are 00 - FF.
[962] CREG Max Registration
Default (C8) Valid entries are 00 - FF.
[963] Retransmission Delay
Default (2D) Valid entries are 00 - FF.
[964] Voice Volume
Default (04) Valid entries are 00 - FF.
[965] Microphone Gain
Default (01) Valid entries are 00 - FF.
[966] SMS Recovery Hour
Default (0018) Valid entries are 0000 - FFFF.
[967] SMS Threshold 1
Default (0032) Valid entries are 0000 - FFFF.
[968] SMS Threshold 2
Default (0064) Valid entries are 0000 - FFFF.
[969] Debug Mask Timeout
Default (2760) Valid entries are 0000 - FFFF.
[970] Monitoring Heartbeat
Default (0060) Valid entries are 0000 - FFFF.
System Information (Read Only)
NOTE: Sections [971] - [998] are provided for information (read-only). Values in these sections cannot
be modified by the installer.
38