User's Manual
Table Of Contents
- Table of Contents
- WARNING: Installer please read carefully
- General
- Model Information
- Panel Mounting
- Features
- Technical Specifications
- Ratings Compatibility
- Pre Installation Configuration
- Communicator Installation Configuration
- Installing Communicator in Panel
- Communicator Placement Test
- Initial Panel Programming
- SMS Command and Control
- Communicator Status LEDs
- Yellow Trouble LED
- Panel Supervision Trouble (2 Flashes)
- SIM Lock Trouble (4 Flashes)
- Cellular Trouble (5 Flashes)
- Ethernet Trouble (6 Flashes)
- Receiver Not Available (7 Flashes)
- Receiver Supervision Trouble (8 Flashes)
- FTC Trouble (9 Flashes)
- Module Configuration Trouble (12 Flashes)
- Red Network Connection Status LED
- (Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength
- Network Activity LEDs - Red and Green(TL2803G(R)E / TL280LE(R) only)
- Communicator Troubleshooting
- Ethernet/Cellular Programming Options
- System Options
- Programming Options
- Communications Reporting Codes
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- SMS Event Notification/Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Ethernet Cellular Programming Worksheets
- System Options
- Programming Options
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Limited Warranty
- EULA
- Regulatory Information
Interval 2:
l If the test transmission fails to the secondary receiver, it will back up to the primary receiver.
l If the test transmission fails to the primary receiver, an FTC trouble will be generated.
Test Transmission Unique to Primary and Secondary Receivers:
Set Ethernet section [026] to (FF); [027] to (FF). Set cellular section [028] to (FF); [029] to (FF).
Interval 1:
l The module will send periodic test transmissions to primary receivers (Ethernet primary and cellular
primary) independently, with no backups.
l If the test transmission fails to any of the programmed primary receivers, an FTC trouble will be gen-
erated
Interval 2:
The module will send periodic test transmissions to secondary receivers (Ethernet secondary and cel-
lular secondary) independently, with no backups.
l If the test transmission fails to any of the programmed secondary receivers, an FTC trouble will be
generated
[026] Ethernet 1 Test Transmission
Default (FF)
Program 00 to disable this event transmission or FF to enable. See system test options (previous page)
for details on settings.
[027] Ethernet 2 Test Transmission
Default (00)
Program 00 to disable this event transmission or FF to enable. See system test options (previous page)
for details on settings.
[028] Cellular 1 Test Transmission
Default (FF)
Program 00 to disable this event transmission or FF to enable. See system test options (previous page)
for details on settings.
[029] Cellular 2 Test Transmission
Default (00)
Program 00 to disable this event transmission or FF to enable. See system test options (previous page)
for details on settings.
NOTE: The time interval (in minutes) between periodic tests is programmed in section [125] (Ethernet)
and section [225] (cellular).
[030] FTC Restore
Default (FF)
Program 00 to disable this event transmission or FF to enable. This event will occur when an FTC
Trouble on the system restores.
[033] Communicator Firmware Update Begin
Default (FF)
Program 00 to disable this event transmission or FF to enable. This event will occur when a com-
municator firmware update begins.
[034] Communicator Firmware Update Success
Default (FF)
Program 00 to disable this event transmission or FF to enable. This event will occur when a com-
municator firmware update has completed successfuly.
Table 10: System Firmware Update Failure
Event
SIA
Identifier
SIA
ReportingCode
CID
Qualifier
CID
Event
Code
CID
Reporting
Code
CID
User/Zone
[037] System FW Update Fail LU 0000 1 9 04 003
NOTE: The communicator will report ´System Update Fail´ only if the panel becomes offline after a
remote firmware update session has started.
[095] SA Incoming Local Port
Default (0C14/3092)
24