User's Manual
Table Of Contents
- Table of Contents
- WARNING: Installer please read carefully
- General
- Model Information
- Panel Mounting
- Features
- Technical Specifications
- Ratings Compatibility
- Pre Installation Configuration
- Communicator Installation Configuration
- Installing Communicator in Panel
- Communicator Placement Test
- Initial Panel Programming
- SMS Command and Control
- Communicator Status LEDs
- Yellow Trouble LED
- Panel Supervision Trouble (2 Flashes)
- SIM Lock Trouble (4 Flashes)
- Cellular Trouble (5 Flashes)
- Ethernet Trouble (6 Flashes)
- Receiver Not Available (7 Flashes)
- Receiver Supervision Trouble (8 Flashes)
- FTC Trouble (9 Flashes)
- Module Configuration Trouble (12 Flashes)
- Red Network Connection Status LED
- (Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength
- Network Activity LEDs - Red and Green(TL2803G(R)E / TL280LE(R) only)
- Communicator Troubleshooting
- Ethernet/Cellular Programming Options
- System Options
- Programming Options
- Communications Reporting Codes
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- SMS Event Notification/Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Ethernet Cellular Programming Worksheets
- System Options
- Programming Options
- System Test Options
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- Command and Control Options
- External Event Label Programming
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Limited Warranty
- EULA
- Regulatory Information
OFF: Ethernet receiver 2 is disabled.
[3] Reserved
[4] Cellular receiver 1 is enabled. Default (ON) OFF for TL2803G(R)E.
ON: Cellular receiver 1 is enabled.
OFF: Cellular receiver 1 is disabled.
[5] Cellular receiver 2 is enabled. Default (ON) OFF for TL2803G(R)E.
ON: Cellular receiver 2 is enabled.
OFF: Cellular receiver 2 is disabled.
[6] Reserved
[7] DLS Over Cellular. Default (ON).
ON: DLS is enabled on the cellular path.
OFF: DLS is disabled on the cellular path.
NOTE: Program this toggle as OFF to prevent DLS from using the cellular path.
NOTE: If this toggle is OFF, DLS sessions will occur on the Ethernet path only, regardlessof the primary
path set in section [005] toggle option [4]. If it is ON, the communicator will connect to the primary
path first for DLS and if the session fails, the secondary path will be used.
[8] Network Trouble Suppression. Default (OFF).
ON: GSM/Ethernet/Supervisory troubles and restore signals follow delay timer as programmed in
section [226].
OFF: GSM/Ethernet/Supervisory troubles and restore signals are sent immediately.
[007] DNS Server IP 1
Default (000.000.000.000)
Enter the IP address for DNS server 1. Format is 4 fields, each field is a 3 digit decimal. Valid range: 000-
255.
NOTE: If no value is programmed and DHCP is used, the DHCP server will configure the address. If an
address is programmed and DHCP is used, the programmed address will be used instead of the
DHCP address.
[008] DNS Server IP 2
Default (000.000.000.000)
Enter the IP address for DNS server 2. Format is 4 fields, each field is a 3 digit decimal. Valid range: 000-
255.
NOTE: If no value is programmed and DHCP is used, the DHCP server will assign this value. If an
address is programmed and DHCP is used, the programmed address will be used instead of the
DHCP address.
[009] Language
Default (01)
OPT Language OPT Language OPT Language OPT Language
01 English 09 Finnish 17 Not Used 25 Ukrainian
02 Spanish 10 German 18 Croatian 26 Slovakian
03 Portuguese 11 Swedish 19 Hungarian 27 Serbian
04 French 12 Norwegian 20 Romanian 28 Estonian
05 Italian 13 Danish 21 Russian 29 Slovenian
06 Dutch 14 Hebrew 22 Bulgarian 30-99 Reserved
07 Polish 15 Greek 23 Latvian
08 Czech 16 Turkish 24 Lithuanian
NOTE: Programming this section with an invalid language will default to English (01).
NOTE: After programming this section, perform a ‘Default Language in section [999][11] to have pro-
grammable labels available in the selected language.
Programming Options
[010] System Toggle Options 3
[1] 2-Way Audio Over Cellular. Default (OFF)
ON: 2-Way Audio Over Cellular is enabled.
OFF: 2-Way Audio Over Cellular is disabled.
[2] Visual verification. Default (OFF)
ON: Visual verification is enabled.
20