WS900 Self-Contained Wireless Security System Including 3G7090 and LT7090 Cellular Alarm Communicator V1.0 User Manual WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Read the entire manual carefully.
Table of Contents 1.0 About Your Security System 1.1 Fire Detection 1.2 Carbon Monoxide Detection 1.3 Testing 1.4 Monitoring 1.5 Maintenance 2.0 General System Operation 2.1 Integrated Keypad 2.2 Panel Indicators 2.3 Important Notice 2.4 Language Selection 2.5 System Models 3.0 Arming the System 3.1 Stay Arming 3.2 Silent Exit Delay 3.3 Away Arming 3.4 Quick Exit 3.5 Arming Errors and Exit Faults 3.5.1 Arming Error 3.5.2 Audible Exit Fault 3.6 Alarm Cancel Window 3.7 Bypass Zones 3.8 Bypass Group 4.
Chapter 1.0 About Your Security System 1.0 About Your Security System Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be fully instructed in its use. Fill out the System Information page with all of your zone information and access codes, and store this manual in a safe place for future reference.
Chapter 1.0 About Your Security System 1.5 Maintenance With normal use, the system requires minimum maintenance. Note the following points: l Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth removes normal accumulations of dust. Replace the standby battery every 3-5 years. l WARNING! Do not attempt to replace the battery or open the enclosure, as there is a risk of electric shock or fire.
Chapter 2.0 General System Operation 2.0 General System Operation Your security system comprises an integrated alarm control/panel and various sensors and detectors. The panel is mounted by the main entry/exit location. The system is self-contained; electronics and standby battery are housed within the unit. Note: Ensure that only the installer or a service professional has access to the system. The security system has several zones of area protection.
Chapter 2.0 General System Operation Item Description 1 2 Power Status Light 4 3 5 6 7 1 Power LED 2 Ready to Arm LED 3 Armed LED 4 Trouble LED 5 WiFi Signal Strength LED 6 Cellular Signal Strength LED 7 Remote Connection LED 8 Microphone 8 LED indicator Description ON Steady AC power is currently connected to the system. Flashing System Test All status LEDs flash at the same time. OFF This indicates the following conditions: l The system is not powered ON.
Chapter 2.0 General System Operation Armed Status Light LED indicator Description ON Steady The partition is armed.. Flashing The system in Alarm. Note: Silent alarms or panic do not flash the Alarm LED. System Test All status LEDs flash at the same time. Installer Walk Test Ready, Trouble, and Arm LEDs flash at the same time. Trouble Status Light OFF The partition is disarmed LED indicator Description ON Steady A system trouble is present.
Chapter 2.0 General System Operation Cellular Signal Strength Status Light LED indicator Description ON Steady (green) Cellular is active with a strong signal connection. ON Steady (yellow) Cellular is active with a weak signal connection. ON Steady (red) There is no signal or no connection, but a connection is expected. Flashes red for a few seconds, then flashes green System Test All status LEDs flash at the same time.
Chapter 2.0 General System Operation 2.3 Important Notice A security system cannot prevent emergencies. It is only intended to alert you and your central station, if applicable, to an emergency situation. Security systems are generally very reliable, but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system must be installed and serviced by qualified security professionals.
Chapter 3.0 Arming the System 3.0 Arming the System You can arm the system using the following options: l Integrated keypad l Tablet l User app l Wireless key (Refer to section 5.0 for a list of UL/ULC listed compatible wireless keys.) 3.1 Stay Arming Stay Arming arms the perimeter of the premises while permitting movement inside. To arm the system in Stay mode, do the following steps: 1. Ensure all protected doors and windows are secure or bypassed and that the Ready indicator is on. 2.
Chapter 3.0 Arming the System When the exit delay has expired, the system is armed and indicated by the following conditions: l The Ready indicator turns off. l The Armed indicator stays on. l The keypad is silent. Note: In Away Arming mode, manually bypassed zones are logged and communicated to the central station.
Chapter 3.0 Arming the System 3.7 Bypass Zones Use the zone bypassing feature when you need access to a protected area while the system is armed, or when a zone is temporarily out of service, but you need to arm the system. Bypassed zones are not able to sound an alarm. As a result, bypassing zones reduces the level of security. If you are bypassing a zone because it is not working, call a service technician immediately to resolve the problem an restore your system to proper working order.
Chapter 4.0 Disarming the System 4.0 Disarming the System You can arm the system using the following options: l Integrated keypad l Tablet l User app l Wireless key (Refer to section 5.0 for a list of UL/ULC listed compatible wireless keys.) To disarm the system on the integrated keypad, do the following steps: 1. Enter your access code. 2. If you open the entry/exit door, a continuous tone indicates that entry delay has started. Enter your access code within ____ seconds to avoid an alarm condition.
Chapter 5.0 Using Wireless Keys 5.0 Using Wireless Keys In addition to the keypad, you can control your system with two-way wireless keys. All wireless key buttons are programmable. Your installer can verify the functions for each key. Using a two-way wireless key, you can arm or disarm the system while you are in close proximity to your house, or you can call for help.
Chapter 6.0 Emergency Keys 6.0 Emergency Keys IMPORTANT: EMERGENCY USE ONLY! The emergency keys generate a fire, auxiliary, or panic alarm and alerts the central monitoring station. To use the emergency keys, do the following steps: 1. Tap the shift key on the keypad. The emergency keys illuminate. Fire Alarm Auxiliary Alarm Panic Alarm 2. Touch the Fire, Auxiliary, or Panic key for 2 seconds, as needed.
Chapter 6.0 Emergency Keys monitoring station. Check with your installer to see if this option has been enabled on your system and for the transmitter delay time. Following the transmitter delay time, you have 5 minutes to enter your user code to cancel an alarm that has been previously transmitted. A cancel signal is sent to the central monitoring station and the system indicates that the cancel signal was transmitted. Call your central monitoring station to avoid a dispatch. 6.
Chapter 7.0 Managing Users 7.0 Managing Users The WS900 system supports up to 100 users, including the Master user. By default, user #1 is the Master user. You cannot disable or delete this user from the system. The system also supports an additional two duress codes, one for each partition. From the user app, you can program and configure attributes for users 2 thru 100. You can assign a user to one or both partitions and enable or disable system interaction.
Chapter 7.0 Managing Users Initiate firmware updates Update the system WiFi SSID and password l Create new users and user labels l Program duress codes Note: Users can only add, edit, or delete users that are assigned to the same partition as they are. l l 7.3 Level 2 Access (Basic/Standard User) Users at this level have access to basic security functions but are limited based on their partition assignment.
Chapter 8.0 Viewing Troubles on the Integrated Keypad 8.0 Viewing Troubles on the Integrated Keypad When the system detects a trouble condition, the Trouble indicator turns on and the system beeps once every 10 seconds. Tap the [*] key to silence the beeps. Note: For UL Listed installations, your access code is required to view system troubles. To view troubles on the integrated keypad, do the following steps: 1. When the keypad illuminates, tap [*][2]. 2. Enter your access code, if required.
Chapter 8.
Chapter 9.0 Testing Your System 9.0 Testing Your System Inform your Monitoring Station when you begin and end system testing. Household fire alarm systems shall be tested by a qualified service technician at least every 3 years in accordance with NFPA72. It is the user’s responsibility to test the system weekly (excluding smoke detectors). Ensure you follow all the steps identified in the following sections. Should the system fail to function properly, call your installer immediately for service. 9.
Chapter 10.0 Safety Instructions 10.0 Safety Instructions This equipment is stationary-DIRECT PLUG-IN and must be installed by Service Persons only (Service Person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons).
Chapter 10.0 Safety Instructions 10.1 Regular Maintenance and Troubleshooting Keep your Alarm Controller in optimal condition by following all the instructions that are included within this manual and/or marked on the product. It is the end-user and/or installer’s responsibility to ensure that the disposal of the used batteries is made according to the waste recovery and recycling regulations applicable to the intended market. 10.
Chapter 11.0 Locating Detectors and Escape Plan 11.0 Locating Detectors and Escape Plan The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke and CO alarms. 11.1 Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.
Chapter 11.0 Locating Detectors and Escape Plan Figure 3a Figure 4 11.2 Fire Escape Planning There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed. 1. Every family member should participate in developing the escape plan. 2. Study the possible escape routes from each location within the house.
Chapter 11.0 Locating Detectors and Escape Plan Figure 5 11.3 Carbon Monoxide Detectors Carbon monoxide is colorless, odorless, tasteless, and very toxic, it also moves freely in the air. CO detectors can measure the concentration and sound a loud alarm before a potentially harmful level is reached. The human body is most vulnerable to the effects of CO gas during sleeping hours; therefore, CO detectors should be located in or as near as possible to sleeping areas of the home.
Chapter 12.0 Installer Warning of flammable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. 12.0 Installer Warning Warning Please Read Carefully Note To Installers: This warning contains vital information.
Chapter 12.0 Regulatory Agency Statements 12.0 Regulatory Agency Statements FCC MODIFICATION STATEMENT Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment .Digital Security Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature.
Chapter 12.0 Regulatory Agency Statements +HUHE\ '6& GHFODUHV WKDW WKLV GHYLFH LV LQ FRPSOLDQFH ZLWK WKH HVVHQWLDO UHTXLUHPHQWV DQG RWKHU UHOHYDQW SURYLVLRQV RI 'LUHFWLYH (& 7KH FRPSOHWH 5 77( 'HFODUDWLRQ RI &RQIRUPLW\ FDQ EH IRXQG DW KWWS ZZZ GVF FRP OLVWLQJVBLQGH[ DVS[ &=( '6& MDNR Y¿UREFH SURKODģXMH ŀH WHQWR Y¿UREHN MH Y VRXODGX VH YģHPL UHOHYDQWQ¯PL SRŀDGDYN\ VPÝUQLFH (& '$1 '6& HUNO¨UHU KHUYHG DW GHQQH NRPSRQHQWHQ RYHUKROGHU DOOH YLNWLJH NU
Chapter 13.0 Reference Sheets 13.0 Reference Sheets Fill out the following information for future reference and store this guide in a safe place. 13.1 System Information Mark if Buttons are Enabled [F] FIRE [M] Medical [P] PANIC The Exit Delay Time is _______ seconds. The Entry Delay Time is _______ seconds. 13.
© 2016 Tyco Security Products. All Rights Reserved. Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3000 • www.dsc.com The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products will aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary.
