User's Manual

ManualsBrandsDigital Security Controls ManualsElectronics3G Cellular Alarm Communicator

Table Of Contents

4005 Series
- Universal Cellular Communicator
  - Figure 1 – Box parts (only GS4005, 3G4005/AM and 3G4005/EU).
  - Figure 2 – Parts identifications: a) ANT5-02, GSM antenna with 2 m cable and SMA connector (accessory item); b) GS4005, 3G4005/AM and 3G4005/EU; c) GS4005-K, 3G4005-K/AM and 3G4005-K/EU.
Hereby, Digital Security Controls declares that the
4005 Series
is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The complete R&TTE Declaration of
Conformity for each Device can be found at www.dsc.com.
The GS4005, GS4005-K, 3G4005/AM, 3G4005/EU, 3G4005-K/AM and 3G4005-K/EU product models have been certified by IMQ/A to be compliant with EN 50136-1:2012 and EN 50136 2:2013 for Alarm transmission system performance SP2 (D2, M2, T2, S0, I0) for vocal/...
The communicator is certified IMQ-SECURITY SYSTEM if powered by the panel and without battery backup.
Installation of these systems must be carried out strictly in accordance with the instructions described in this manual, and in compliance with the
local laws and bylaws in force. The above mentioned devices have been designed and made to the highest standards of
quality and performance. The manufacturer recommends that the installed system should be completely tested at least once a month.
Digital Security Controls shall not be responsible for damage arising from improper installation or maintenance by unauthorized personnel.
Digital Security Controls reserves the right to change the technical specifications of this product without prior notice.
Recycling information
Digital Security Controls recommends that customers dispose of their used equipment (panels, detectors, sirens, and other devices) in an environmentally sound manner. Potential methods include reuse of parts or whole products and recycling of product...
Waste Electrical and Electronic Equipment (WEEE) Directive
In the European Union, this label indicates that this product should NOT be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. For specific information see http://www.dsc.com
INTRODUCTION
PC PROGRAMMING
APPENDIX
- EN 50136-2: 2013 compliance
  - Table 9: Wiring diagram A: with simulated PSTN.
  - Table 10: Wiring diagram B: without simulated PSTN.
- Pass-Through

4005 Series

Universal Cellular Communicator

Summary of content (49 pages)

PAGE 1
4005 Series Universal Cellular Communicator
PAGE 2
N. Parts 1 Cover 2 Backplate 3 LED max. GSM reception 4 LED min. GSM reception 5 Trouble LED 6 GSM connection LED 7 Fixing screw (provided in the side position 7, Figure 2) 8 GSM antenna 9 Hinges for closing cover 10 Antenna cable hole 11 2700mAh rechargeable battery (accessory Item): only GS4005, 3G4005/AM and 3G4005/EU N. Parts 17 USB port: only GS4005, 3G4005/AM and 3G4005/EU 18 Antitamper contact 19 Terminal boards 20 Positioning pins for PCB mounting 21 Jumper 1: see par.
PAGE 3
Figure 2 – Parts identifications: a) ANT5-02, GSM antenna with 2 m cable and SMA connector (accessory item); b) GS4005, 3G4005/AM and 3G4005/EU; c) GS4005-K, 3G4005-K/AM and 3G4005-K/EU.
PAGE 4
INTRODUCTION 5 General description . . . . . . . . . . . . . . . . . . . . . 7 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Terminals description . . . . . . . . . . . . . . . . . . 13 Connection example . . . . . . . . . . . . . . . . . . . 14 USB Functionality . . . . . . . . . . . . . . . . . . . . . 15 Power Monitor . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating Principles . . . . . . . . . . . . . . . . . . . 17 Event Priority management. . . . . . . . . . . . . .
PAGE 5
INTRODUCTION Devices in the 4005 Series are GSM communicators which, in the absence of a PSTN line, transmits vocal and digital alarms to System III or System II receivers, via GPRS GPRS Quad-Band (HSPA Dual-Band). The following models are available. GS4005: communicator with 2G module in the plastic cabinet. 3G4005/AM: communicator with 850/1900 MHz 3G module, in the plastic cabinet. 3G4005/EU: communicator with 900/1800 MHz 3G module, in the plastic cabinet.
PAGE 6
Technical Specifications The supply voltage for this communicator is provided by the Control panel connected (10.7 V to 27.6 V) or from an external power supply that provides the 12 V and recharging, if necessary, a back-up battery (accessory item). The only purpose of the battery is to provide the power in the event the primary power source is lost. The required autonomy in stand-by is 8 hours. In both cases, if the main power is lost the battery assures that the panel will still powered and working.
PAGE 7
Jumpers Description See Figure 2 on page 3. Jumper 21 j pins 1 and 2 connected, no input current limit (default); k pins 2 and 3 connected, input current limit (450 mA, from battery charger side). PST (Pass-Through) J open, Pass-Through disabled (default); K closed, the communicator will be able to perform remote programming of the PC 1864 4.1 EU, PC 1864 4.2 EU, PC 1864 4.2 ADT Spain and PC 1864 4.5 ADT Spain DSC Power Series intrusion panels, via cellular and PC-Link.
PAGE 8
GS4005-K, 3G4005-K/AM and 3G4005-K/EU mounting  This Communicator shall be installed by qualified SERVICE PERSONS only, in the shelter of a safe and dry site, away from radiotransmitting equipment. Test the GSM Network reception before mounting this Communicator in the proposed placement. Do not route any wiring over circuit boards. The length of the power cables cannot exceed 3 meters.
PAGE 9
Figure 3 – GS4005-K, 3G4005-K/AM and 3G4005-K/EU Mounting: A) antenna; B) magnetic base; C) metal box; D) support; E) Communicator board; F) main board control panel; G) board hole; H) four adhesive plastic supports; I) metal box base.
PAGE 10
GS4005, 3G4005/AM and 3G4005/EU mounting See Figures 1 and 2. 1. 2. ! 3. 4. 5. 6. 7. 8. Mark the position of the holes [8] required to fix the plastic base [2] and the antitamper device [13] to the wall. Drill holes in the wall as marked. Make sure you do not damage wiring or pipes in the chase. Insert the 5 supports into the holes on the wall. Feed the connection cables through the opening on the base. Fix the plastic base to the wall using wall anchors (not supplied).
PAGE 11
of the Communicator, open the cover and check that the SMS and / or voice message is sent to the programmed telephone numbers and the output is enabled. Status LEDs There are 8 LEDs on the PCB that indicate the Communicator status.  During start-up, all LEDs will be ON less 1 second. During the programming default procedure, LEDs OFF while the LEDs LED and and will be will be ON. Colour Name Description Green/Yellow GSM signal strength Packet Service Network Type (see Table 4).
PAGE 12
Communication Type Slow Flashing Slow Flashing Device initialization: the LEDs flash until a GSM signal is received by the Communicator. Fast Flashing Incoming SMS: the LED flashes a few seconds. OFF Slow Flashing OFF Remote Session: the LED may flashes a few seconds after the end of session. OFF Voice call: it signals the voice calls of the Communicator NOT those of connected control panel, if any. Slow Flashing Table 6: Communication Type. Fault LED This LED is normally OFF.
PAGE 13
Terminals description Terminal Description - Ground: this terminal must be connected to the Mains Earth, in order to comply with the Telecommunications Network Safety Standards (Overvoltage Protection Requirements). LI Internal telephone line: these terminals must be connected to the control panel or an alternative communication terminal. LE External telephone line: these terminals can be connected to the PSTN line. T1 Default: output, PSTN fault. T2 Default: output, no cellular network.
PAGE 14
Connection example ! Incorrect connections may result in FTC fault or improper operation. Inspect wiring and ensure connections are correct before applying power. DO NOT route any wiring over circuit boards; maintain at least 1” (24.5 mm) separation. A minimum 1/4” (6.4 mm) separation must be maintained at all points between Power Limited wiring and all other Not-Power Limited wiring.
PAGE 15
USB Functionality The communicator has an USB A connector. It shall be implemented a dual-role feature: may be Host or Device according to the jumper setting: Device: J (open default), or Host K (closed) and allows the direct insertion of USB memory stick (see page 7 “Jumpers description”). To connect the communicator to a PC it is necessary to have an A to A USB cable (Hub cable). The USB interface characteristics:  Compliance, USB 2.0 Specification  Data rate, Full speed (12 Mbit/s)  Max.
PAGE 16
Power Monitor The device will be powered in two ways: 1. 2. By the Control panel with a backup battery. In this case the device will be powered in the range from 10.7 V to 27.6 V. By an external power supply to provide the 12V. In this case the communicator will recharge the optional battery. The only purpose of the battery is to provide the power in the event the primary power source is lost. The autonomy in stand-by is 8 hours.
PAGE 17
Operating Principles This Communicator offers the option of selecting the “Primary Communication Path” for communication purposes (the default configuration is external PSTN). Will provide the line ring voltage for incoming calls and will decode DTMF dialling. The Simulated land line provides the alarm control panel or an alternative communication terminal, with a backup line in the event of PSTN line trouble. Commutation between PSTN and GSM, does NOT occur during ongoing calls.
PAGE 18
GSM pre-set channel This provides the devices connected to the LI terminals with a simulated line if GSM reception is detected. If there is no GSM reception, it commutates to the PSTN telephone line. Contact ID transmission sequence on GPRS The Communicator, if telephone numbers have been entered on the page Phonebook using the software DLS 5 Console, directs calls to these numbers over the GPRS line.  When an event is triggered, the Alarm Panel goes off-hook.  The dial tone is simulated.
PAGE 19
3. 4. The Communicator waits for a response from the number called for a period of up to 60 seconds. If the outcome is positive, the Communicator moves on to step 4; otherwise the call will end and step 1 will be attempted again, up to a maximum of 8 times (depending on the programmed value). After 8 attempts the call cycle will be considered complete.
PAGE 20
Internal events In addition to external events (decoded CID/SIA events from the panel via simulated PSTN line), the communicator will manage following internal events.              Trigger / restore of input Status reporting events Mains power source failure / restore (required by EN50136-2:2013). Battery power source failure / restore (required by EN50136-2:2013); valid only for the version with battery charger on board.
PAGE 21
Panel Transmission Monitoring (PTM) The constant monitoring of communication with the control unit (PTM function) allows the Communicator to transmit calls via the GSM network if communication between the alarm control panel and the surveillance control unit does not take place successfully over the PSTN telephone line. If programmed (using the DLS 5 Console PTM page), this feature only works when the PSTN line is connected to the LE terminals.  Pulse dialling detection is not supported.
PAGE 22
The default programming for each terminal is shown below:  PSTN Fault (T1).  GSM Fault (include SIM Fault) (T2).  Reserved Output, Remote output activation via Caller ID and/or SMS functionality (T3).  No Cellular network (T4).  IP receiver Fail (T5) required by EN50136-1:2012, paragraph 6.6; EN50136-2:2013, Annex A).
PAGE 23
SMS Send an SMS consisting of the User code between the * characters, the Control string (Control String can not have initial blank spaces) and the characters “=ON*”, “=ON*TonU*” or “=OFF*”, as follows: #User Code*String=ON* #User Code*String=ON*TonU* #User Code*String=OFF* The “=ON*tonU*” option is parameter allows to set the ON Time from 1 to 86400 seconds, with 1 second steps. The ON Time can be set by means of the Communicator's Console software.
PAGE 24
Remote Programming by SMS Messages In addition to the processes described in the section Remote activation and deactivation of the outputs, it is also possible to carry out other remote procedures through the transmission of various SMS messages.
PAGE 25
Credit balance check To find out the credit balance via SMS, you can either use the DLS 5 Console software (see section Programming via PC->Options->Pay As You Go), or you can find out remotely by sending an SMS message consisting of the characters “#CCC” followed by the * character, in accordance with the following formula: #CCC*User PIN* or for the Installer code: #ICCC*Installer PIN*  The balance SMS will be sent to the Telephone Number of the sender.
PAGE 26
An SMS feedback will be automatic sent to the sender in the event of success Enable Level 4 This command is used by the Installer in order to enable the Level 4 access, via a SMS message remotely send a SMS message consisting of the characters “#ENM” followed by the * character, in accordance with the following formula: #ENM*InstallerPIN* An SMS feedback will be automatic sent to the sender in the event of success. After a time-out of 12 hour period the Level 4 will be automatically disabled.
PAGE 27
PC PROGRAMMING  For proper function of this Communicator, use a 32 K SIM CARD (or higher). For programming, the PC-Link cable (not supplied) must be connected to the Connector [15] of the Communicator and a COM port on the PC (see Figure 5); the DLS 5 Console application is also required. The PC-Link cable shown in Figure 5, can be used for the connection. Make sure you insert the PC-Link cable connector in the right way.
PAGE 28
Menu description  FILE menu  New Account: the command “New Account”, creates a new customer and assign the Default values to all parameters of programming.  Account Group Maintenance: to group multiple customers.  Recent Files: to select an existing customer.  Exit: the command closes the DLS 5 Console. You will be asked to save the changed data of the current installation.  VIEW menu  Start Page: corresponds to click on the field Start Page.  Operators on Line: list of the connected Operators.
PAGE 29
Common icons in the various programming pages. Clear All Tags. Programming/ Audio and Import/Export. Restore all options to Default. Restore all options to originals. This icon has a different meaning depending on the pages of Programming. This icon has a different meaning depending on the pages of Programming. Firmware Update: this icon is shown only when the Installer level 4 is enabled (see previous page); it allows you to run the firmware update procedure.
PAGE 30
 Level 2 (Normal User): access to information about the operational status of the communicator (i.e. use of the software console in order to read the device status page and the programming options). Access level 2 may also allow access to basic functional tests and the management of other Access level 2 users and to enabled the Installer Code. It requires a PIN (Default value: 000000).
PAGE 31
 PTM: click on to enabled the “PTM” function on the selected numbers, which allows the device to transmit calls over the GSM network in the event of failed communication between the control Panel and the receiver on the PSTN telephone line. By default is disabled.  CID/SIA Event conversion: enable the trigger of voice call and/or SMS by decoding CID/SIA coming from the panel (see table on page 37).
PAGE 32
4. in the Communicator the call is forwarded to the phone number 3661730826.  If the option “Digits to remove” is enabled and a panel calls a phone number that has the “CID/SIA Conversion” enabled (see “Phonebook”), the phone number in the “Phonebook” must match the typed by the panel (including the prefix), in this case the communicator will carry out the conversion.
PAGE 33
 Enquiry Type: selection of enquiry type (none, SMS, Call, Service Command).  Enquiry Number: telephone number to call or to which an SMS message should be sent in order to request credit balance information.  Balance Message: string used to send SMS messages and to make requests via service commands.  Enquiry Interval: Enter the interval (HH-DD) at which you wish to send a periodic SMS containing credit balance information (if supported by your telephone operator).
PAGE 34
Input/output This page is used to program input or output modes, output activation events, polarity (N.C. or N.O.), reserved outputs and remote activation SMS strings for reserved outputs.  Input/Output: double click on number to see the programming of the Input/output selected.  Label: enter an alphanumeric string of 16 characters max.
PAGE 35
 FTC fault: if selected, the output will be activated if communication is not successful  The selection of the FTC Signal event enables the Monostable option and allow to set the Monostable Time (ON Time).  Type Monostable: Normally the outputs, when activated, remain so until a deactivation command is received, at which point the output will revert to its standby status.
PAGE 36
 Periodic SMS/Call First Send: Select the date /hour on which the first periodic SMS/voice message is to be sent.  To comply with the EN50136-2:2013 standards the time “Periodic SMS/Call First Send” should be set equal to 1 day and this function should not be changed (default: 1 day).  You MUST enter the “SIM Phone Number” and enable the “Auto SMS” and “IP Clock Adjust “in the “Options” page to setup the Periodic options above.  Now: if click on this icon you can get the date and time from the PC.
PAGE 37
SIA  Date/Time on SIA packet: if is enabled, on the SIA package will also include the date and time.  Label: this column lists / describes the events for which to send a message.  Each input can be programmed with a specific Customer code (account).     Customer Code: enter the Customer Code (4 hexadecimal characters). Contact ID Identifier: enter the Contact ID code that the communicator will sent when the event occurs.
PAGE 38
 Phone Number Use: 1 SMS Phone Numbers; 2 Voice Dialer Phone Numbers. Double Click on 1 to enable phone numbers for SMS Communicator, 8 of 32 phone numbers of the phonebook; Double Click on 2 to enable phone numbers for Voice Communicator, 8 of 32 phone numbers of the phonebook.  Label: this column lists the events for which a voice message / SMS. can sent.
PAGE 39
 Main receiver APN: enter the Access Point Name of the GPRS service provider being used. Enter the name of the IP address service provider in this box.  Make sure to enter the correct APN for WAP/GPRS access - otherwise some functions may be limited (for more information, please contact your customer support).  Main receiver User name: some providers may require a user name to validate communication. If needed, enter this information here.
PAGE 40
Programming/Audio Import/Export Import Audio Button - Press this button to import the recorded voice messages from a USB stick. The communicator will convert the file in the voice messages to use in the system. Export Audio Button - Press this button to export the recorded voice messages on a USB stick. The communicator will convert them into a file that can be used on another system. Import Programming Button - Press this button to import the communicator programming from a USB stick.
PAGE 41
PTM  Check Dialing: disabled at factory default, if enabled, the missed dialing (i. e. when the PTM does not detect the number dialed by the control panel on the PSTN line) will be count as failure by the “PTM function”.  PTM Max Errors Before Takeover: in this box, enter the total number of errors detected by the Communicator above which the PTM function is activated. The PTM function is disabled by default (the default setting is 0); set a value from 1 to 4 to enable the PTM function.
PAGE 42
Firmware update  To update the firmware it is necessary to enter in the system with the prerogatives / password of the Level 4 Installer. The communicator, in this page, manages the Firmware upgrade both local than remote (via Cellular Data Network). The communicator will be able to work while Firmware update is in progress The device Firmware upgrade will be stored in the flash memory on the board.
PAGE 43
APPENDIX EN 50136-2: 2013 compliance The Communicator, to comply to EN 50136-2: 2013, must be configured and connected to a Control Panel, only in one of two following ways, A or B: A) use PSTN (the control panel will made the control, of the response of the receiver, directly on the PSTN).  PSTN: terminals LI of the communicator connected to terminals of the Control Panel for the external telephone line.
PAGE 44
See the tables below. Communicator LI Control Panel  LE     Output “LE presence detection” T1: Output “PSTN Fault” T2: Output “No cellular network” Default T3: “Panel interconnection Present” T4: Output “Tamper” T5: Output “GSM Fault” T6: Output “Jamming Detect” Input “Tamper” Communicator Input “GSM Fault” Input “Jamming Detect” Table 9: Wiring diagram A: with simulated PSTN.
PAGE 45
Pass-Through This feature allows the Power Series PC1864 control panels (PC 1864 4.1 EU, PC 1864 4.2 EU, PC 1864 4.2 ADT Spain, PC 1864 4.5 ADT Spain, PC 1864 4.5 EU) to be programmed remotely via GPRS using the Communicator and the DLS 5 console software updated with the “Driver pack for the 4005 Series”. The Communicator must be properly programmed before connecting it to the Power Series PC1864 control panel.
PAGE 46
Remote programming with the DLS 5 console To remotely program the control panel, you must have installed the DLS 5 console software on your PC with the driver update package downloaded from the DSC site.  In order to get support on DLS 5 for the Communicator, you must install the “Driver pack for the 4005 Series”.
PAGE 47
4005 Series 47
PAGE 48
FCC Compliance Statement CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception.
PAGE 49
Digital Security Controls www.dsc.com ISTISD2EGS4005 0.