User's Manual
Table Of Contents
- WARNING: Installer please read carefully
- General Information
- Communicator Technical Specifications
- Communicator Pre Intsallation Configuration
- Communicator Configuration with SCW
- Installation Location
- Installing CAT 5 Cable (TL2553G(R)-E only)
- INSERTING/REMOVING THE SIM CARD
- Communicator Reset
- Establishing a Communication Channel with the SCW Panel.
- Initial Programming of Communicator and SCW
- SMS Command and Control Functions
- Label Programming for SMS Message
- Communicator Placement Test
- Ethernet/Cellular Programming Options
- System Options
- Programming Options
- Communications Reporting Codes
- System Test Options [026 - 029]
- Ethernet Receiver 1 Options
- Ethernet Receiver 2 Options
- Ethernet Options
- Cellular Receiver 1 Options
- Cellular Receiver 2 Options
- Cellular Options
- Command and Control Options
- SMS Command and Control Functions
- SMS Command and Control Response
- Receiver Diagnostic Testing
- System Information (Read Only)
- System Reset Defaults
- Communicator Troubleshooting
- Communicator Troubleshooting
- Ethernet Cellular Programming Worksheets
- EULA
- Limited Warranty
- Regulatory Information
that Cellular radio reception is adequate for communication using the HSPA/3G paths. Perform the “Communicator Placement
Test” on page 9.
Communicator Technical Specifications
General Information
All versions of the HSPA/3G and Ethernet Alarm Communicator, operate on a HSPA/3G network and are housed inside the
Self Contained Wireless (SCW) 9055/9057. The Communicators use an Internal Antenna only.
Each version of Alarm Communicators covered by this Installation Manual are described below:
3G2055-E: A High Speed Packet Access/Global System for Mobile (HSPA/3G) wireless Alarm Communicator that sends
alarm communication to Sur-Gard System I, II, III (SG-DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers
via a HSPA/3G digital cellular network.
3G2055R-E: A High Speed Packet Access/Global System for Mobile (HSPA/3G) wireless Alarm Communicator that sends
alarm communication to Sur-Gard System I, II, III (SG-DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers
via a HSPA/3G digital cellular network. This model also includes an interface for connecting to 3rd party applications.
TL2553G-E: Is a dual-path Cellular/Ethernet Alarm Communicator that sends alarm communication to Sur-Gard System I, II, III,
and IV central station receivers through Ethernet/Internet or a HSPA/3G digital cellular network.
The dual path Communicator can be used as either a backup or primary Communicator. The Communicator supports Internet
Protocol (IP) transmission of panel and internal events over Ethernet/Internet and/or HSPA/3G.
TL2553GR-E: Is a dual-path Cellular/Ethernet Alarm Communicator that sends alarm communication to Sur-Gard System I, II,
III, and IV central station receivers through Ethernet/Internet or a HSPA/3G digital cellular network.
The dual path Communicator can be used as either a backup or primary Communicator. The Communicator supports Internet
Protocol (IP) transmission of panel and internal events over Ethernet/Internet and/or HSPA/3G. This model also includes an
interface for connecting to 3rd party applications.
NOTE: For North America the following model names are available: 3G2055-E, 3G2055R-E, TL2553G-E and TL2553GR-E.
CAUTION:
l Do not stay close to the equipment during device operation and to do not touch any exposed wires and other conductive
surfaces,
l Recycle the battery according to the local rules and regulations.
NOTE: Prior to installation of the 3G2055(R)-E or TL2553G(R)-E Communicator, confirm with your local carrier that the
HSPA/3G network is available and active in the area where the Communicator will be installed, and that the location
provides a radio signal strength that is adequate for uninterrupted service.
Features
l 128-bit Advanced Encryption Standard (AES) encryption via HSPA/3G and Ethernet/Internet.
l Activating, initializing and remote programming through Connect 24.
l Back up or primary HSPA/3G/2G alarm communication.
l Does not require an external HSPA/3G/2G antenna.
l Ethernet LAN/WAN 10/100 BaseT (TL2553G(R)-E only).
l Full event reporting to central station.
l Fully redundant Ethernet/Internet and HSPA/3G/2G Dual-path Alarm Communication (TL2553G(R)-E only).
l Individual Ethernet and/or HSPA/3G periodic test transmission.
l 2-way audio (listen-in feature) provided over Cellular.
l Integrated call routing.
l Remote Firmware upgrade capability of the Communicator and Panel Firmware via Ethernet and/or HSPA/3G radio.
l Dual-Band Operation: 850 MHz, and 1900 MHz. (North America only)
l CID and SIA format reporting.
l Subscriber Identity Module (SIM) card included with Communicator. (North America only)
l Supervision heartbeats via HSPA/3G/2G and/or Ethernet/Internet.
UL/ULC Installation Requirements
l For ULC Residential fire and burglary applications the 3G2055(R)-E/TL2553G(R)-E can be used as primary com-
munication channel via either Cellular or Ethernet (as applicable) or as a back-up in conjunction with the Digital Alarm
Communicator Transmitter (DACT). Test transmission every 24hours shall be enabled on each channel.
l For UL Residential fire and burglary applications the 3G2055(R)-E/TL2553G(R)-E can be used as primary communication
channel via either Cellular or Ethernet, or as a back-up in conjunction with the DACT. (30 day test transmission is required
on each channel).
6