Installation Manual
Table Of Contents
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG_FRONT
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG_TOC
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG
- Features
- Technical Specifications
- Ratings
- Parts
- 1
- Plastic Casing
- 2
- Anchor Screw Holes (3mm)
- 3
- SIM Card Holder
- 4
- 3G Antenna
- 4A
- 3G External Antenna (Optional)*
- 5
- 3G (HSPA) Radio Module
- 6
- Antenna Connector
- 7
- Antenna Mounting Hardware
- 8
- Tamper Switch
- 9
- Status LEDs (see page 5)
- 10
- Terminal Blocks
- 11
- PC-Link Connector
- 12
- Battery Connector
- 13
- Cable Entry
- 14
- 7.2V - 2.2Ah Battery
- * Use only DSC provided antenna.
- Description
- 1. Remove the front panel.
- 2. Fit the 3G antenna [2]. Ensure the 3G antenna mounting hardware is fastened securely [3].
- 3. Attach the 3G radio module with the 3G antenna connector. Ensure that the connector is secure.
- 4. Turn on the 3G4000 and check the signal strength. 4.1 Connect the battery connector. 4.2 Connect the DC power source to +/- 12V terminals.
- 5. Allow the unit to power up.
- 6. Power down the 3G4000 by removing the DC power source and battery leads.
- 1. Using the cabinet, mark the four screw locations. Drill the anchor screw holes.
- 2. Using anchor screws (not provided), mount the cabinet to the wall.
- 3. Run the cables through the cable entry [13] or through the cabinet knockouts.
- 4. Complete the connections on the terminal blocks [11].
- 5. Reattach the front cover [1] securely to the cabinet.
- Simulated Landline Mode
- Panel Transmission Monitoring (PTM)
- Wireless Communications Sequence
- Inputs
- Outputs
- Activating the Outputs
- Swinger Shutdown
- Hardware Default
- Low Power Radio Shutdown
- Figure 2 - Wiring Diagram
- Figure 3 - Telephone Connection
- Figure 4 - Power Supply and Supervision Wiring Diagram
- Figure 5 - Fire Alarm Control Unit and 3G Transmitter
- Figure 6 - DSC Subscribers’ Unit Fire and 3G Transmitter Mounted in the Same Room
- Figure 7 - DSC Subscribers’ Unit Fire and 3G Wireless Transmitter Mounted Remotely
- Description
- Limited Warranty
Identification of Parts
2
Figure 1 - Parts
ARE
A
ROUT
A
R
EA
ROUT
AREA
ROUT
INHI
BI
T
SI
INHIBITINHIBIT
ANT1
-
+
OPEN OPEN
UA674
JK1
REV02
TH2
FIDB1
SW1
CON2
C94
C95
C97
FIDB4
FIDB2
TH3
CON1
C96
M
2
CON5
TH1
PCLINK
SERIAL NUMBER
1000X500
TIP RING T1 R1
Z1 PGM1 Z2 PGM2
DC IN
+
-
14
13
10
8
2
9
11
12
4A
2
53 64
7
1
All circuits are classified for UL installations as Power Limited/Class II Power Limited except for the battery
leads which are not power limited. Do not route any wiring over circuit boards. Maintain at least 1” (25.4mm)
separation. A minimum 1/4” (6.4mm) of separation must be maintained at all points between Power Limited
wiring and all other non-Power Limited wiring. Route wires as indicated above.
NOTE:
NOTE:
For UL/ULC installations,
For UL/ULC installations,
connections between the alarm
connections between the alarm
control panel outputs (telephone
control panel outputs (telephone
interface Tip/Ring, output relay
interface Tip/Ring, output relay
contacts) and 3G4000 inputs
contacts) and 3G4000 inputs
(Tip/Ring, Z1-Z4) shall be run in
(Tip/Ring, Z1-Z4) shall be run in
a mechanical protective conduit
a mechanical protective conduit
within 20ft (6m) of one another
within 20ft (6m) of one another
and in the same room
and in the same room
.
.
NOTE: For UL/ULC installations,
connections between the alarm
control panel outputs (telephone
interface Tip/Ring, output relay
contacts) and 3G4000 inputs
(TIP/RING/Z1/Z2) shall be run in
a mechanical protective conduit
within 20ft (6m) of one another
and in the same room.
Table1:Parts
Parts
1 Plastic Casing
2 Anchor Screw Holes (3mm)
3 SIM Card Holder
4 3G Antenna
4A 3G External Antenna (Optional)*
5 3G (HSPA) Radio Module
6 Antenna Connector
7 Antenna Mounting Hardware
8 Tamper Switch
9 Status LEDs (see page 5)
10 Terminal Blocks
11 PC-Link Connector
12 Battery Connector
13 Cable Entry
14 7.2V - 2.2Ah Battery
* Use only DSC provided antenna.