Installation Manual
Table Of Contents
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG_FRONT
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG_TOC
- DFTAU1114_29009079R001_3G4000_V4.0_IM_NA_ULC_UL_ENG
- Features
- Technical Specifications
- Ratings
- Parts
- 1
- Plastic Casing
- 2
- Anchor Screw Holes (3mm)
- 3
- SIM Card Holder
- 4
- 3G Antenna
- 4A
- 3G External Antenna (Optional)*
- 5
- 3G (HSPA) Radio Module
- 6
- Antenna Connector
- 7
- Antenna Mounting Hardware
- 8
- Tamper Switch
- 9
- Status LEDs (see page 5)
- 10
- Terminal Blocks
- 11
- PC-Link Connector
- 12
- Battery Connector
- 13
- Cable Entry
- 14
- 7.2V - 2.2Ah Battery
- * Use only DSC provided antenna.
- Description
- 1. Remove the front panel.
- 2. Fit the 3G antenna [2]. Ensure the 3G antenna mounting hardware is fastened securely [3].
- 3. Attach the 3G radio module with the 3G antenna connector. Ensure that the connector is secure.
- 4. Turn on the 3G4000 and check the signal strength. 4.1 Connect the battery connector. 4.2 Connect the DC power source to +/- 12V terminals.
- 5. Allow the unit to power up.
- 6. Power down the 3G4000 by removing the DC power source and battery leads.
- 1. Using the cabinet, mark the four screw locations. Drill the anchor screw holes.
- 2. Using anchor screws (not provided), mount the cabinet to the wall.
- 3. Run the cables through the cable entry [13] or through the cabinet knockouts.
- 4. Complete the connections on the terminal blocks [11].
- 5. Reattach the front cover [1] securely to the cabinet.
- Simulated Landline Mode
- Panel Transmission Monitoring (PTM)
- Wireless Communications Sequence
- Inputs
- Outputs
- Activating the Outputs
- Swinger Shutdown
- Hardware Default
- Low Power Radio Shutdown
- Figure 2 - Wiring Diagram
- Figure 3 - Telephone Connection
- Figure 4 - Power Supply and Supervision Wiring Diagram
- Figure 5 - Fire Alarm Control Unit and 3G Transmitter
- Figure 6 - DSC Subscribers’ Unit Fire and 3G Transmitter Mounted in the Same Room
- Figure 7 - DSC Subscribers’ Unit Fire and 3G Wireless Transmitter Mounted Remotely
- Description
- Limited Warranty
3G4000 Wiring Diagrams
13
Figure 3 - Telephone Connection
RED (R)
GREEN (T)
GRAY (R)
BROWN (T)
RJ-31X
RING
TIP
CONTROL PANEL
Incoming
Phone lineHandset
RI
TI
TI
RI
TIP
RING
3G4000
TIP RING T1 R1 Z1 PGM1 Z2 PGM2 DC IN
+
-
1 2 3 4 5 6 7 98 10
Figure 4 - Power Supply and Supervision Wiring Diagram
Control
Panel
EOL
Resistor
See Note 3
CONTROL PANEL
DSC
Supervision
Relay
See Note 2
DSC
RM-2
RELAY
NC
C
NO
+12VDC
GND
Aux Power
+ -
3G4000
(BLK/WHT) +13.8VDC
(BLK ) GND
DSC ADP1310-NAU
Power Adaptor
TIP RING T1 R1 Z1 PGM1 Z2 PGM2 DC IN
+
-
1 2 3 4 5 6 7 9
ZONE
TERMINALS
(See Note 1)
- +
8 10
NOTES
1. Program the Zone/Point as “Supervisory” type
with keypad only annunciation when in Alarm.
Do NOT use a point that is normally used for
2-Wire Smoke detectors.
2. The power Supervision relay, RM-2 is only used
when the 3G4000 is not powered by the control
panel. When the Radio is powered by the control
panel the relay is not required since a loss of
input power will generate a signal to the CMC.
3. Output 4 on the 3G4000 must be set as “Active
High” (default).
4. When powering the 3G4000 Radio by an Auxiliary
Power supply that has its own backup battery,
insert JP3 jumper on the radio and remove the
1.2AH battery that came with the radio.
The following wiring diagrams (Figures 5 to 7) are examples of ULC Listed Fire Monitoring Installation
connections.